1、BSI Standards PublicationBS EN 1559-4:2015Founding Technicalconditions of deliveryPart 4: Additional requirements foraluminium alloy castingsBS EN 1559-4:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 1559-4:2015. It supersedes BS EN 1559-4:1999 which is w
2、ithdrawn.The UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a
3、 contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 83651 0 ICS 77.150.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under
4、the authority of the Standards Policy and Strategy Committee on 28 February 2015.Amendments/corrigenda issued since publication#Date T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1559-4 February 2015 ICS 77.150.10 Supersedes EN 1559-4:1999English Version Founding - Tech
5、nical conditions of delivery - Part 4: Additional requirements for aluminium alloy castings Fonderie - Conditions techniques de fourniture - Partie 4: Spcifications complmentaires pour les pices moules en alliages daluminium Gieereiwesen - Technische Lieferbedingungen - Teil 4: Zustzliche Anforderun
6、gen an Gussstcke aus Aluminiumlegierungen This European Standard was approved by CEN on 26 December 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteratio
7、n. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by
8、translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, F
9、inland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZ
10、ATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1559-4:2015 EBS EN 1559-4:2015Contents Page F
11、oreword 3 Introduction . 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 5 4 Information to be supplied by the purchaser 6 4.1 Mandatory information 6 4.2 Optional information 6 4.3 Drawing, patterns and tools 6 4.4 Information on the mass . 6 4.5 Preliminary sample 6 4.6 Initial samp
12、le 6 5 Designations . 6 6 Manufacture 6 6.1 Manufacturing process 6 6.2 Welding operations 6 7 Requirements . 7 7.1 General 7 7.2 Material 7 7.3 Casting 7 8 Inspection . 9 8.1 General 9 8.2 Type of inspection documents and type of inspection 9 8.3 Test unit 9 8.4 Samples. 9 8.5 Test procedures . 9 8
13、.6 Invalidation of test results. 9 8.7 Retests 9 8.8 Sorting and reprocessing 9 9 Marking . 9 10 Packaging and surface protection . 9 11 Complaints 9 Annex A (informative) Procedure for the classification of excavation for finishing welding 10 Annex B (informative) Significant technical changes betw
14、een this European Standard and the previous edition . 12 Bibliography 13 EN 1559-4:2015 (E)BS EN 1559-4:2015Foreword This document (EN 1559-4:2015) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard
15、shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2015 and conflicting national standards shall be withdrawn at the latest by August 2015. Attention is drawn to the possibility that some of the elements of this doc
16、ument may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1559-4:1999. Within its programme of work, Technical Committee CEN/TC 132 requested CEN/TC 132/WG 22 “Revision of EN 1559-4:1999“ to
17、revise the following standard: EN 1559-4, Founding Technical conditions of delivery Part 4: Additional requirements for aluminium alloy castings. Annex B provides details of significant technical changes between this European Standard and the previous edition. This European Standard is part of a ser
18、ies of standards which specify technical delivery conditions for castings. The other standards in this series are: EN 1559-1, Founding Technical conditions of delivery Part 1: General; EN 1559-2, Founding Technical conditions of delivery Part 2: Additional requirements for steel castings; EN 1559-3,
19、 Founding Technical conditions of delivery Part 3: Additional requirements for iron castings; EN 1559-5, Founding Technical conditions of delivery Part 5: Additional requirements for magnesium alloy castings; EN 1559-6, Founding Technical conditions of delivery Part 6: Additional requirements for zi
20、nc alloy castings. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Mac
21、edonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. EN 1559-4:2015 (E)BS EN 1559-4:2015Introduction In order to assist m
22、anufacturers and purchasers to prepare proper contractual arrangements and prevent misunderstandings, CEN/TC 190 “Foundry Technology“ approved the preparation of a series of standards covering technical delivery conditions. These have been prepared as separate parts. This European Standard covers th
23、e additional technical delivery conditions for aluminium alloy casting materials and has the same structure as EN 1559-1 “Founding - Technical conditions of delivery Part 1: General“. This European Standard cannot be used alone for compiling a specification for ordering and supplying aluminium alloy
24、 castings, but as a complement to EN 1559-1. The structure of this standard is as follows: clauses and sub clauses preceded by indicate no additional conditions to EN 1559-1; clauses and sub clauses marked with a single dot indicate that conditions shall be agreed at the time of enquiry and order; c
25、lauses and sub clauses marked with two dots indicate that conditions can be agreed at the time of enquiry and order (optional); clauses and sub clauses without a symbol are mandatory; clauses and sub clauses preceded by are supplementary to those in EN 1559-1; clauses and sub clauses preceded by com
26、pletely replace those in EN 1559-1. EN 1559-4:2015 (E)BS EN 1559-4:20151 Scope This European Standard specifies the additional technical delivery conditions for aluminium alloy castings unless other conditions have been agreed at the time of enquiry and order. This European Standard retains the same
27、 structure and numbering system as used in EN 1559-1 and repeats the numbering of clauses and sub-clauses even if nothing extra or different has been added. It also indicates items specific to aluminium alloy castings under existing or new headings. 2 Normative references The following documents, in
28、 whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1371-1, Founding Liquid penetra
29、nt testing Part 1: Sand, gravity die and low pressure die castings EN 1559-1, Founding Technical conditions of delivery Part 1: General EN 1706, Aluminium and aluminium alloys Castings Chemical composition and mechanical properties EN 12681, Founding Radiographic examination 3 Terms and definitions
30、For the purposes of this document, the terms and definitions given in EN 1559-1, in the applicable material standard and the following apply. 3.1 excavation cavity produced by the removal of cast material prior to subsequent welding (or other finishing methods) EN 1559-4:2015 (E)BS EN 1559-4:20154 I
31、nformation to be supplied by the purchaser 4.1 Mandatory information 4.2 Optional information 4.3 Drawing, patterns and tools 4.4 Information on the mass 4.5 Preliminary sample 4.6 Initial sample If required, a minimum of two initial samples shall be supplied to the purchaser for approval. If these
32、initial samples are accepted, one shall be retained by the purchaser and one returned to the manufacturer marked as “approved“. Supplementary initial samples (one for metallurgical and the other for dimensional purposes) should be retained either by the manufacturer or by the purchaser. NOTE Testing
33、 of initial samples by the manufacturer can be agreed. 5 Designations 6 Manufacture 6.1 Manufacturing process 6.2 Welding operations 6.2.1 General 6.2.2 Production welding Production welding is permitted, unless otherwise agreed at the enquiry and order stage. For railway applications, production we
34、lding has to be agreed separately (see EN 15085-2). Actions to finish castings or eliminate casting imperfections may include the use of a filler metal deposited by a suitable welding process or the insertion of a machined piece secured by welding. The manufacturers and purchasers attention is drawn
35、 to the need for approved procedures and suitably qualified welders (see EN ISO 15614-4, for finishing welding). After preparing the casting for finishing welding, the excavation can be classified in accordance with the procedure given in Annex A. 6.2.2.1 6.2.2.2 EN 1559-4:2015 (E)BS EN 1559-4:20156
36、.2.2.3 6.2.2.4 6.2.2.5 6.2.2.6 7 Requirements 7.1 General 7.2 Material 7.2.1 Chemical composition NOTE Metal is usually taken for optical emission spectrometry analysis at the time the castings are made, in the form of a chill cast disc (see EN 14361). 7.2.2 Mechanical properties 7.2.3 Other propert
37、ies 7.2.4 Additional requirements The manufacturer shall examine the results of any treatment of the melt carried out during the melting process by using appropriate methods. 7.3 Casting 7.3.1 Chemical composition For chemical composition of aluminium alloy castings, refer to the appropriate table i
38、n EN 1706. 7.3.2 Mechanical properties 7.3.3 Outer and inner conditions (non-destructive testing) Liquid penetrant examination shall be carried out in accordance with EN 1371-1. Radiographic inspection shall be carried out in accordance with EN 12681. Where applicable, unacceptable external and inte
39、rnal discontinuities shall be eliminated by production welding (see 6.2.2) or other agreed methods. 7.3.3.1 7.3.3.2 7.3.3.3 7.3.3.4 EN 1559-4:2015 (E)BS EN 1559-4:20157.3.4 Conditions of the casting 7.3.4.1 Shape and size 7.3.4.2 Fettling and finishing 7.3.4.3 In order to eliminate leaks in castings
40、, it is possible with the approval of the purchaser, to use impregnation. The impregnation medium and method, maximum permitted size of discontinuities and retest procedures shall be agreed between purchaser and manufacturer. 7.3.4.4 In the case of as cast castings, it is recommended that the purcha
41、ser agrees with the manufacturer on the choice of any non-destructive testing and criteria to determine the acceptability of a subsequently machined surface. Unless specifically agreed, discontinuities revealed on the machined surface should not be regarded as a cause for rejection. If the porosity
42、on machined surfaces is to be assessed, manufacturer and purchaser should agree on the method to be used. 7.3.5 Mass of the casting 7.3.6 Additional requirements regarding the conditions of the casting 7.3.6.1 Macrostructure Where appropriate, a macroscopic examination of a suitably prepared and etc
43、hed section shall be used to assess the grain size and/or structural discontinuities of a casting to agreed criteria. Assessment is usually carried out with or without low magnification. 7.3.6.2 Microstructure Where appropriate, a microscopic examination of a suitably polished and etched section sha
44、ll be used to determine the metallurgical structure of a casting to agreed criteria. Assessment is usually carried out at a high magnification and includes the nature, shape and distribution of the structural constituents. NOTE A cooling curve/thermal analysis carried out on a sample of liquid alloy
45、 before casting, can predict, to a limited extent, the metallurgical structure to be expected in the casting. 7.3.6.3 Density evaluation can be used to estimate the soundness of castings by weighting in air and water to agreed criteria. EN 1559-4:2015 (E)BS EN 1559-4:20158 Inspection 8.1 General 8.2
46、 Type of inspection documents and type of inspection 8.3 Test unit 8.3.1 Formation of test units 8.3.2 Size of test units 8.3.3 Inspection frequency When tests are requested, unless any agreement to the contrary has been made, one test per test unit shall be carried out. For hardness testing, the in
47、spection frequency shall be agreed between the manufacturer and the purchaser by the time of acceptance of the order. 8.4 Samples 8.5 Test procedures 8.6 Invalidation of test results 8.7 Retests 8.7.1 General 8.7.2 Non-sequential tests (individual values) 8.7.2.1 Retest of chemical composition If di
48、sagreement occurs between the manufacturer and the purchaser on the chemical composition of a test unit the manufacturer shall re-check the composition wherever possible on the original test piece. If disagreement persists, a referee analysis shall be carried out by a mutually acceptable laboratory.
49、 8.7.3 Sequential tests 8.8 Sorting and reprocessing 9 Marking 10 Packaging and surface protection 11 Complaints EN 1559-4:2015 (E)BS EN 1559-4:2015Annex A (informative) Procedure for the classification of excavation for finishing welding The procedure for the classification of excavations for finishing welding is as follows: - measure
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1