1、BRITISH STANDARD BS EN 1654:1998 Incorporating Corrigenda Nos. 1, 2 and 3 Copper and copper alloys Strip for springs and connectors The European Standard EN 1654:1998 has the status of a British Standard ICS 77.150.30 BS EN 1654:1998 This British Standard, having been prepared under the direction of
2、 the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 April 1998 BSI 27 March 2003 ISBN 0 580 29463 3 National foreword This British Standard is the English language version of EN 1654:1998, including Corrigendum July 2002. Together with
3、BS EN 1652:1998 and BS EN 1653:1998 it supersedes BS 2870:1980 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee NFE/34, Copper and copper alloys, to Subcommittee NFE/34/1, Wrought and unwrought copper and copper alloys, which has the responsibility to:
4、 A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “Internationa
5、l Standards Correspondence Index”, or by using the “Search” facility of the BSI Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard doe
6、s not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and pr
7、omulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 33 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Sidelining in this document indicates the most r
8、ecent changes by amendment. Amendments issued since publication Amd. No. Date Comments 10196 Corr. No. 1 September 1998 14083 Corr. No. 2 17 January 2003 14412 Corr. No. 3 27 March 2003 Indicated by a sidelineEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1654 December 1997 ICS 77.150.30 Incor
9、porating corrigendum July 2002 Descriptors: Copper, copper alloys, rolled products, steel strips, springs, connectors, designation, chemical composition, mechanical properties, dimensions, dimensional tolerances, sampling, tests English version Copper and copper alloys Strip for springs and connecto
10、rs Cuivre et alliages de cuivre Bandes pour ressorts et connecteurs Kupfer und Kupferlegierungen Bnder fr Federn und Steckverbinder This European Standard was approved by CEN on 6 November 1997. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions
11、for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three offici
12、al versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Be
13、lgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secret
14、ariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1654:1997 EEN 1654:1998 BSI 27 March 2003 2 Foreword This European Standard has been prepared by Technical Committee CEN/TC 133, Copper
15、 and copper alloys, of which the Secretariat is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 1998, and conflicting national standards shall be withdrawn at the latest by June
16、1998. Within its programme of work, Technical Committee CEN/TC 133 requested CEN/TC 133/WG 2, Rolled flat products, to prepare the following standard: EN 1654 Copper and copper alloys Strip for springs and connectors. This is one of a series of European Standards for copper and copper alloy rolled f
17、lat products. Other products are, or will be, specified as follows: EN 1172, Copper and copper alloys Sheet and strip for building purposes. EN 1652, Copper and copper alloys Plate, sheet, strip and circles for general purposes. EN 1653, Copper and copper alloys Plate, sheet and circles for boilers,
18、 pressure vessels and hot water storage units. EN 1758, Copper and copper alloys Strip for lead frames. Copper and copper alloys Copper plate, sheet and strip for electrical purposes. (WI: 00133022) This standard gives information, which might be useful to the user, on physical properties of the pro
19、duct contained in Annex A. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembour
20、g, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword 2 1S c o p e 3 2 Normative references 3 3 Definition 3 4 Designations 3 4.1 Material 3 4.2 Material condition 4 Page 4.3 Product 4 5 Ordering information 5 6 Requirements 6 6.1 Composition 6 6
21、.2 Mechanical properties 6 6.3 Dimensions and tolerances 6 6.4 Form tolerances 6 6.5 Surface properties 7 7S a m p l i n g 7 7.1 General 7 7.2 Analysis 7 7.3 Mechanical and other tests 8 8 Test methods 8 8.1 Analysis 8 8.2 Hardness test 8 8.3 Bend test 8 8.4 Tensile test 8 8.5 Spring bending test 8
22、8.6 Coil set 8 8.7 Transverse cross bow q 9 8.8 Retests 9 8.9 Rounding of results 9 9 Declaration of conformity and inspection documentation 9 9.1 Declaration of conformity 9 9.2 Inspection documentation 9 10 Marking, packaging, labelling 9 Annex A (informative) Properties for guidance 32 Annex B (i
23、nformative) Bibliography 33 Table 1 Composition of copper alloys 12 Table 2 Mechanical properties 14 Table 3 Tolerances on thickness 29 Table 4 Tolerances on width 29 Table 5 Materials to which special width a n d d e f l e c t i o n t o l e r a n c e s a r e n o t a p p l i c a b l e (see Tables 4
24、and 9) 30 Table 6 Edgewise curvature c for strip condition “as rolled” (N) 30 Table 7 Transverse cross bow q for strip condition “as rolled” (N) 31 Table 8 Edgewise curvature c for strip condition “as flattened” (G) 31 Table 9 Coil set for strip condition “as flattened” (G) 31 Table 10 Waviness v fo
25、r strip condition “as flattened” (G) 31 Table 11 Transverse cross bow q for strip condition “as flattened” (G) 31 Table A.1 Properties for guidance 32EN 1654:1998 BSI 27 March 2003 3 1 Scope This European Standard specifies the composition, property requirements and tolerances on dimensions and form
26、 for copper alloy strip intended for the fabrication of springs and connectors, with thicknesses from 0,1 mm up to and including 1,0 mm and with widths up to and including 350 mm. The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and th
27、e delivery conditions are also specified. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated ref
28、erences, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies. EN 1655, Copper and copper alloys Declarations of conf
29、ormity. EN 10002-1, Metallic materials Tensile testing Part 1: Method of test (at ambient temperature). EN 10204, Metallic products Types of inspection documents. prEN 12384, Copper and copper alloys Determination of spring bending limit on strip. ISO 1811-2, Copper and copper alloys Selection and p
30、reparation of samples for chemical analysis Part 2: Sampling of wrought products and castings. ISO 6507-2, Metallic materials Hardness test Vickers test Part 2: HV 0,2 to less than HV 5. ISO 6507-3, Metallic materials Hardness test Vickers test Part 3: Less than HV 0,2. ISO 7438, Metallic materials
31、Bend test. NOTE Informative references to documents used in the preparation of this standard, and cited at the appropriate places in the text, are listed in a bibliography (see Annex B). 3 Definition For the purposes of this standard, the following definition, based on ISO 197-3, applies. 3.1 strip
32、flat rolled product of rectangular cross-section with uniform thickness from at least 0,10 mm, supplied level wound as coils, or on cores or spools, or traverse wound on cores or spools, usually with slit edges; the thickness does not exceed one tenth of the width 4 Designations 4.1 Material 4.1.1 G
33、eneral The material is designated either by symbol or number (see Table 1). 4.1.2 Symbol The material symbol designation is based on the designation system given in ISO 1190-1. NOTE Although material symbol designations used in this standard might be the same as those in other standards using the de
34、signation system given in ISO 1190-1, the detailed composition requirements are not necessarily the same. 4.1.3 Number The material number designation is in accordance with the system given in EN 1412.EN 1654:1998 4 BSI 27 March 2003 4.2 Material condition For the purposes of this standard, the foll
35、owing designations, which are in accordance with the system given in EN 1173, apply for the material condition: R. material condition designated by the minimum value of tensile strength requirement for the product with mandatory tensile strength and elongation requirements; H. material condition des
36、ignated by the minimum value of hardness requirement for the product with mandatory hardness and bending radius requirements; Y. material condition designated by the minimum value of 0,2 % proof strength requirement for the product with mandatory 0,2 % proof strength and elongation requirements; B.
37、material condition designated by the minimum value of spring bending limit for the product with mandatory spring bending limit requirements and in some cases also with bending radius requirements. Exact conversion between material conditions designated R., H., Y., B. is not possible. Material condit
38、ion is designated by only one of the above designations. 4.3 Product The product designation provides a standardized pattern of designation from which a rapid and unequivocal description of a product is conveyed in communication. It provides mutual comprehension at the international level with regar
39、d to products which meet the requirements of the relevant European Standard. The product designation is no substitute for the full content of the standard. The product designation for products to this standard shall consist of: denomination (strip); number of this European Standard (EN 1654); materi
40、al designation, either symbol or number (see Table 1); material condition designation (see Table 2); nominal dimensions (thickness width) and tolerance classes for thickness and width (A or B); strip condition “as rolled” (N) or “as flattened” (G). The derivation of a product designation is shown in
41、 the following example. EXAMPLE Strip conforming to this standard, in material designated either CuSn6 or CW452K, in material condition H180, nominal thickness 0,500 mm, tolerance class A for thickness, nominal width 199,6 mm, tolerance class A for width, in strip condition “as flattened”, shall be
42、designated as follows: EN 1654:1998 BSI 27 March 2003 5 5 Ordering information In order to facilitate the enquiry, order and confirmation of order procedures between the purchaser and the supplier, the purchaser shall state on his enquiry and order the following information: a) quantity of product r
43、equired (mass); b) denomination (strip); c) number of this European Standard (EN 1654); d) material designation (see Table 1); e) material condition designation (see 4.2 and Table 2); f) nominal thickness; g) tolerance class for thickness (see Table 3); h) nominal width; i) tolerance class for width
44、 (see Table 4); j) strip condition (N or G); k) coil size requirements: nominal inside diameter in millimetres and maximum outside diameter in millimetres, and either maximum mass in kilograms or approximate specific coil weight (mass per width) in kilograms per millimetre; l) spool size: type or di
45、mensions. NOTE It is recommended that the product designation, as described in 4.3, is used for items b) to j). In addition, the purchaser shall state on the enquiry and order any of the following, if required: m) whether edgewise curvature for strip condition “as rolled” shall be measured over a le
46、ngth of 2 000 mm (see 6.4.2.1); n) whether strip is required to meet roughness requirements R a , R zor R max.(see 6.5.2). If so, the test method and the acceptance criteria required; o) which measuring device is to be used for the determination of transverse cross bow (see 8.7); p) whether a declar
47、ation of conformity is required (see 9.1); q) whether an inspection document is required, and if so, which type (see 9.2); r) whether there are any special requirements for marking, packaging or labelling (see clause 10). EXAMPLE Ordering details for 1 500 kg strip conforming to EN 1654, in material
48、 designated either CuSn6 or CW452K, in material condition H180, nominal thickness 0,500 mm, tolerance class A for thickness, nominal width 199,6 mm, tolerance class A for width, in strip condition “as flattened”, nominal inside diameter of coil 400 mm, maximum outside diameter 900 mm, approximate sp
49、ecific coil weight (mass per width) 4 kg/mm: 1 500 kg strip EN 1654 CuSn6 p H180p 0,500A 199,6A p G nominal inside diameter of coil 400 mm maximum outside diameter of coil 900 mm approximate specific coil weight 4 kg/mm or 1 500 kg strip EN 1654 CW452Kp H180p 0,500A 199,6Ap G nominal inside diameter of coil 400 mm maximum outside diameter of coil 900 mm approximate specif
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1