1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 1730:2012Furniture Tables Test methods for the determination of stability, strength and durabilityBS EN 1730:2012 BRITISH STANDARDNational forewordThis British Standard is
2、the UK implementation of EN 1730:2012. It supersedes BS EN 1730:2000, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e F W / 0 / 1 , C o m m o n T e s t M e t h o d s f o r F u r n i t u r e .A list of organizations represented on this c
3、ommittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012.ISBN 978 0 580 73047 4 ICS
4、97.140 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 1730:2012EUROPEAN STA
5、NDARD NORME EUROPENNE EUROPISCHE NORM EN 1730 October 2012 ICS 97.140 Supersedes EN 1730:2000English Version Furniture - Tables - Test methods for the determination of stability, strength and durability Ameublement - Tables - Mthodes dessai pour la dtermination de la stabilit, de la rsistance et de
6、la durabilit Mbel - Tische - Prfverfahren zur Bestimmung der Standsicherheit, Festigkeit und Dauerhaltbarkeit This European Standard was approved by CEN on 18 August 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Europea
7、n Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (
8、English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgi
9、um, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzer
10、land, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref
11、. No. EN 1730:2012: EBS EN 1730:2012EN 1730:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 General test conditions .54.1 Preliminary preparation 54.2 Application of forces .54.3 Tolerances 55 Test Equipment and Apparatus 56 Test Procedures - Strength
12、and durability 86.1 General 86.2 Horizontal static load test .86.3 Vertical static load tests . 146.3.1 Vertical static load on main surface . 146.3.2 Additional vertical static load test where the main surface has a length 1 600 mm 156.3.3 Vertical static load on ancillary surface . 166.4 Horizonta
13、l durability and stiffness test 176.4.1 General . 176.4.2 Horizontal durability test 176.4.3 Stiffness of the structure . 216.5 Vertical durability test 236.6 Vertical impact test . 236.6.1 General . 236.6.2 Vertical impact test for glass table tops . 236.6.3 Vertical impact test for all other table
14、 tops 236.7 Deflection of table tops 236.8 Durability of tables with castors . 246.9 Drop test 247 Test procedures Stability 257.1 General . 257.2 Stability under vertical load . 257.2.1 General . 257.2.2 Test for tables that are or can be set to a height of 950 mm or less . 257.2.3 Test for tables
15、that are or can be set to a height greater than 950 mm 277.3 Stability for tables with extension elements 277.4 Stability of tables designed to support a parasol . 278 Test procedures - Height adjustment mechanisms 288.1 General . 288.2 Durability of Height adjustment mechanisms . 28BS EN 1730:2012E
16、N 1730:2012 (E) 3 Foreword This document (EN 1730:2012) has been prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at
17、the latest by April 2013, and conflicting national standards shall be withdrawn at the latest by April 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or a
18、ll such patent rights. This document supersedes EN 1730:2000. The main changes with respect to the previous edition are listed below. All test methods for seating used in European Standards for furniture have been collated in one document. The document now contains methods that were previously liste
19、d in EN 581-3, Outdoor furniture, EN 527-3, Office Work Tables and Desks and EN 15372, Non-domestic tables. A durability test for tables with castors has been added. A durability test for height adjustment mechanisms has been added. Wherever possible test methods have been simplified and clarified f
20、or ease of use. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedo
21、nia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 1730:2012EN 1730:2012 (E) 4 1 Scope This European Standard specif
22、ies test methods for the determination of stability, strength and durability of the structure of all types of tables and desks without regard to use, materials, design/construction or manufacturing process. This European Standard does not apply to changing units which are covered by other European S
23、tandards. Test methods for the assessment of ageing, degradation, and electrical functions are not included. This European Standard does not apply to the strength and durability of any storage features that are covered by other European Standards. This European Standard does not include any requirem
24、ents. Requirements for different end uses can be found in other Standards. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated ref
25、erences, the latest edition of the referenced document (including any amendments) applies. EN 14072:2003, Glass in furniture Test methods ISO 7619-2, Rubber, vulcanized or thermoplastic Determination of indentation hardness Part 2: IRHD pocket meter method 3 Terms and definitions For the purposes of
26、 this document, the following terms and definitions apply. 3.1 structure load bearing parts of furniture such as the frame, top and legs 3.2 ancillary surface surface additional to the main surface intended for occasional use as part of the table top 3.3 duty cycle length of time the height adjustab
27、le tables drive system may be operated without impairing its useful life 3.4 levelling device device intended to keep the table top horizontal e.g. adjustable feet or similar BS EN 1730:2012EN 1730:2012 (E) 5 4 General test conditions 4.1 Preliminary preparation The furniture shall be tested as deli
28、vered. Knock-down furniture shall be assembled according to the instructions supplied with it. If the instructions allow the furniture to be assembled or combined in different ways, the most adverse combination shall be used for each test. Knock-down fittings shall be tightened before testing. Furth
29、er tightening shall not take place unless specifically required by the manufacturer. Unless otherwise specified by the manufacturer, the sample for test shall be stored in indoor ambient conditions for at least 24 h immediately prior to testing. The tests shall be carried out at indoor ambient condi
30、tions but if during a test the temperature is outside the range 15 C to 25 C the maximum and/or minimum temperature shall be recorded in the test report. The test for deflection of table tops (see 6.7), except those made from metal, glass and stone, shall be carried out at a relative humidity of (50
31、 5) % and a temperature of (23 2) C. 4.2 Application of forces The test forces in durability and static load tests shall be applied sufficiently slowly to ensure that negligible dynamic load is applied. The forces in durability tests shall be applied sufficiently slowly to ensure that kinetic heatin
32、g does not occur. Unless otherwise stated, static loads shall be maintained for (10 2) s. Unless otherwise stated, durability loads shall be maintained for (2 1) s. The forces may be replaced by masses. The relationship 10 N = 1 kg shall be used. 4.3 Tolerances Unless otherwise stated, the following
33、 tolerances are applicable to the test equipment: Forces: 5 % of the nominal force; Velocities: 5 % of the nominal velocity; Masses: 1 % of the nominal mass; Dimensions: 1 mm of the nominal dimension; Angles: 2oof the nominal angle. The accuracy for the positioning of loading pads and impact plates
34、shall be 5 mm. NOTE For the purposes of uncertainty measurement, test results are not considered to be adversely affected when the above tolerances are met. 5 Test Equipment and Apparatus Unless otherwise stated, the tests may be applied by any suitable device because the results are not dependent u
35、pon the apparatus, except in the case of impact tests where the apparatus described in 5.2 shall be used. The equipment shall not inhibit deformation nor cause unnatural deformation of the unit/component, i.e. it shall be able to move so that it can follow the deformation of the unit/component durin
36、g testing. BS EN 1730:2012EN 1730:2012 (E) 6 With the exception of the horizontal static, durability and stiffness tests, described in 6.2 and 6.4, all loading pads shall be capable of pivoting in relation to the direction of the applied force and the pivot point shall be as close as practically pos
37、sible to the load surface. Loading pads for the horizontal static, durability and stiffness tests, described in 6.2 and 6.4, shall not pivot. With the exception of the horizontal static, durability and stiffness tests described in 6.2 and 6.4, if a loading pad tends to slide, use a slip resistant ma
38、terial between the loading pad and the surface being tested. 5.1 Vertical impactor, as shown in Figure 1 and comprised of the following: 5.1.1 Circular body, 200 mm in diameter separated from the striking surface by helical compression springs and free to move relative to it on a line perpendicular
39、to the plane of the central area of the striking surface. The body and associated parts minus the springs shall have a mass of (17 0,1) kg and the whole apparatus, including mass, springs and striking surface, shall have a mass of (25 0,1) kg. 5.1.2 Springs, which shall be such that the nominal spri
40、ng rate of the combined spring system is (7 2) N/mm and the total friction resistance of the moving parts is less than 1 N. The spring system shall be compressed to an initial load of (1 040 5) N (measured statically) and the amount of spring compression movement available from the initial compressi
41、on point to the point where the springs become fully closed shall be not less than 60 mm. 5.1.3 Striking surface, which shall be a rigid circular object, 200 mm in diameter, the face of which has a convex spherical curvature of 300 mm radius with a 12 mm front edge radius. BS EN 1730:2012EN 1730:201
42、2 (E) 7 Key 1 joint of lifting device not inhibiting free fall Figure 1 Vertical Impactor 5.2 Floor, horizontal, flat and rigid with a smooth surface. For the drop test (6.9) the floor shall be faced with a 2 mm thick layer of rubber with a hardness of 85 10 IRHD according to ISO 7619-2. BS EN 1730:
43、2012EN 1730:2012 (E) 8 5.3 Stops, to prevent the article from sliding but not tilting, no higher than 12 mm except in cases where the design of the item necessitates the use of higher stops, in which case the lowest that will prevent the item from moving shall be used. 5.4 Loading pad, a rigid cylin
44、drical object, 100 mm in diameter, with a flat, smooth face and a 12 mm edge radius. 5.5 Foam, 25 mm thick layer of flexible foam with a bulk density of (120 25) kg/m3. 5.6 Steel test tube, (18 1,5) mm in diameter and (1,5 0,5) mm in wall thickness with a length such that a force can be applied at a
45、 distance of 2 200 mm above the floor. 5.7 Test surface for castor durability tests, horizontal, flat smooth and rigid steel surface. 5.8 Obstacles for castor durability tests, steel strips 50 mm wide and 2 mm high with the top edges having a radius of 2 mm, 500 mm apart and parallel on the floor su
46、rface and perpendicular to the test direction. 6 Test Procedures - Strength and durability 6.1 General Unless otherwise specified, the tests shall be carried out in the configuration most likely to cause failure. Where the table top can be extended, and the smallest dimension of the unextended table
47、 top is less than 300 mm, then the extended configuration shall be considered most likely to cause failure. In this case, the extended configuration is considered to be the main surface. Levelling devices shall be set as near as possible to 5 mm from the fully open position whilst ensuring the table
48、 top is parallel to the floor. If a test cannot be carried out as specified in this standard, e.g. because a loading pad cannot be used for the application of a force due to the design of a product, the test shall be carried out as far as possible as specified. Tables supplied with storage features
49、shall be tested with the specified load in the storage item. 6.2 Horizontal static load test Position the table on the test surface, in its normal position of use without extending, or inserting, ancillary surfaces. Unless otherwise specified, height adjustable tables shall be set to their highest position. Restrain the base of the table by stops placed in all directions at the opposite end to that at which the horizontal test force is
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1