EN 1869-1997 en Fire Blankets《防火毯》.pdf

1、* * rn - STD.BS1 BS EN LbS-ENGL 1797 m 1b2Libb Ob3q05Li T5T BRITISH STANDARD Fire blankets The European Standard EN 1869 : 1997 has the status of a British standard ICs 13.220.10 BS EN 1869 : 1997 ini n-mm U- NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGH LAW u u COPYRIGHT Europea

2、n Committee for StandardizationLicensed by Information Handling Services - STD-BSI BS EN LBb7-ENGL 1777 lb24bb9 Ob34055 99b Amd. No. BS EN 1869 : 1997 Date Text affected Committees responsible for this British Standard The preparation of this British Standaxd was entrusted by Technical Committee FSH

3、/2, Fire extingushen, to Subcommittee FSW13, Fire blankets, upon which the foliowing bodies were represented: British Fire Consortium British Leather Confederation Chief and Assistant Chief Fire officers Association Consumer Policy Committee of BSI Department of the Environment (Building Research Es

4、tablishment) Fire Extinguishing Wes Association Home office International Wool Secretariat London Fire and Civil Defence Authority Loss Prevention Council Marine Safety Agency Minishy of Defence Society of Motor Manufacturers and n-aders Ltd. This British Standard, having been prepared under the dir

5、ection of the Consumer Products and Services Sector Board, was published under the authority of the Standards Board and comes into effect on 15 May 1997 O BSI 1997 The foiiowing BSI references relate to the work on this standard Committee reference FSW2/13 Draft for comment 951540740 DC ISBN O 680 2

6、7403 9 I I COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesBS EN 1869 : 1997 Contents page Committees responsible inside front cover National foreword 11 Foreword 2 Text of EN 1869 3 O BSI 1997 i COPYRIGHT European Committee for StandardizationLicensed by Inf

7、ormation Handling ServicesSTD-BSI BS EN L8bS-ENGL I777 = Ib24bbS Ob34057 7b7 BS EN 1869 : 1997 National foreword This British Standard has been prepared by Subcommittee FSW13 and is the English ianguage version of EN 1869 : 1997 Ere blankets published by the European Commitke for Standardization (CE

8、N). EN 1869 was produced as a result of intemational discussion in which the United Kingdom took an active part. EN 1869 : 1997 supemedes the requirements of BS 6575 : 1985 covering lightduty fire biankets. The scope of BS 6575 : 1985 is currently being revised to cover heavyduty re blankets only. O

9、n publidon of the revised standard, BS 6575 : 1985 wiii be withdrawn. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6, an insid

10、e back cover and a back cover. ii O BSI 1997 COPYRIGHT European Committee for StandardizationLicensed by Information Handling Services STD - BSI EUROPEAN - BS EN L8bS-ENGL 1777 D Lb24bbS Ob3Li058 bT5 NORIME EuR0PEE”E EUROP- NORM EN 1869 January 1997 ICs 13.220.10 Descriptors: Fire fighting equipment

11、, fire blankets, disposable equipment, specifications, classifications, composition: properties, marking, fre tests, electrical resistance English vemion couvertnires anti-feu -decken This European standard was approved by CEN on 199612-19. CEN members are bound to comply with the CENKENELEC Intemal

12、 Regulations which stipulate the conditions for giving this European Standard the status of a national sandard Uptodate lists and bibliographical references concerning such national standards may be obtained on application to the Centsal Secretariat or to any CEN member. This European Standard exist

13、s in three official versions (English, French, German). A version in any other ianguage made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officiai versions. CEN members are the national standarcis bod

14、ies of Austria, Belgium, Denmark, FWand, France, Gem, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. without any alteration. CEN European Committee for Standardization Comit Europen de Normaiisation Europisches Komitee fir N

15、ormung Centrai Secretariat: rue de Stassart 36, B-1060 Brussels O 1997 Copyright reserved to CEN members. Ref. No. EN 1869 : 1997 E COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesPage 2 EN 1869 : 1997 Foreword This European Standard has been prepared by Tech

16、nical Committee CENAC 70, Manual means of fire fighting equipment, the secretariat of which is held by IBN. This European Standard shaii be given the status of a nationai standard, either by publication of an identical text or by endorsement, at the latest by July 1997, and confiidhg nationai standa

17、rds shaii be withdrawn at the latest by July 1997. Accordmg to the CENKENELEC Internal Regulations, the nationa standards organizations of the following countries are bound to implement this European Stan* Austria, Belgium, Denmark, Finland, Fiance, Germany, Greece, Iceland, ireland, Italy, Luxembou

18、rg, Netherlands, Norwax Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Introduction 1 Scope 2 Definitions 3 Construction 4 Freperformance 6 Marking Annexes A (nonnative) Test requirements B (nonnative) Electrid resistance test C (normative) Fire performance test D (informative

19、) Bibliography page 3 3 3 3 3 3 O BSI 1997 COPYRIGHT European Committee for StandardizationLicensed by Information Handling Services STD-BSI BS EN LbS-ENGL 1997 ltb24bbS Ob3LiOb0 253 W it VI n Introduction Some materials used for fire blankets may be degraded or even burn on prolonged contact with f

20、lame but the commitke consider that this should not restrict the use, for the purposes described here, of materials which meet the performance requirements of this siandard A test for electrid resistance of the complete fire blanket is given to ensure that in the event of use where live electrical e

21、quipment is concerned, the potential for an electrical shock is minimized. in addition to the performance requirements specified in this standard it is recommended that re blankets be suitably treated where necessary to give adequate resistance to attack by micro-organisms and insects throughout the

22、 design Me. 1 scope This standard specifies requirements for re blankets which are not re-useable and that are intended for use by one person. It is applicable to fire blankets primarily intended for extinguishmg cooking oil fres. NUE. It is anticipated that they can also be used on fires involving

23、personal clotung. 2 Definitions For the purposes of this European standard the foiiowing definiton applies. Fire blanket A flexible sheet of material intended to be used to extinguish smal fires by smothering. 3 Construction 3.1 A fire blanket shall be formed of one sheet of maeriai, or two or more

24、sheets of material each of a size equal to the overall size of the fire blanket, which are stitched together. The two sides shall be similar in performance. There shall be no seams in the fire blanket except as follows if required a) where the hand-holding devices are xd, and b) at any edge. 3.2 Han

25、d holding devices shall not comprise loops, they shall not be flammable, and shall not become detached from the fire blanket during any of the testing specified in this standard. 3.3 Fire blankets shal be rectangular or square and no edge shal be less than 0,9 m or more than 1,8 m. 3.4 The total mas

26、s of any fire blanket shail not exceed 4,5 kg. Page 3 EN 1869 : 1997 36 Fire blankets shali be capable of bei rolled completely around a (50 + 2) mm diameter bar, and along any axes parallel to eacent sides, without permanent deformation. 3.6 When stowed or packed in accordance with the manufacturer

27、s instnictions, it shall be possible for a fire blanket to be taken from the stowed position, unfolded, and held ready for use in not more than 4 s. The force required to remove the ire blanket sha not exceed 80 N. 3.7 When tested in accordance with annex B, the electrical resistance of the blanket

28、material shall be not less than 1 Mil at any point. 3.8 The edges of the fire blankets shall not fray or tear during any of the tests specified in annexes A to C. 4 Fire performance 4.1 When tested in accordance with annex C, the fire blanket shall be capable of extinguishuig the cookjng oilfreasdes

29、cribedinannexCusingthe (345f5)mm diameter tray, see figure C.l for details. 4.2 The fire blanket shall remain whole and not ignite during the test. 6 Marking 6.1 Each blanket shal be indelibly marked with the mufacturers or suppliers name and address, the number EN 1869 and year of this standard and

30、 the model or type number. 6.2 The container shal be marked with the following in white lettering on a red background. These markings shall be visible when the container is xed in position. a) The words FIRE BLANKET in letters not less b) Model or type number. c) The instruction DISCARD AF”IER USE.

31、d) instructions for use incorporating pictograms and including an instruction to cover burning material completely, switch off heat and leave covered und Cool. 6.3 Either the reverse of the container or a leaflet shall be mked with the following. than20mmhlgh. a) The number of this European Standard

32、. b) Instsuctions prescribing an annual service. c) Blanket size in metres by metres. d) Folding instructions. COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesPage 4 EN 1869 : 1997 Annex A (normative) Wst requirements Al Except where otherwise specified, test

33、s shall be carried out at a temperatwe of (20 f 10) “C. A2 Ail tests shall be carried out using a single thickness of the re blanket. Each re blanket shall be testedseparately. A3 A minimum of three fire blankets shall be tested Identify and mark the blankets as 1 to 3 and the two sides as a or b. T

34、wo of the blankets shail be tested on side a, and one on side b. A.4 The fire blanket shali be conditioned in air at (20 f 10) OC, at a relative humidity of (60 f 10) % for 48 h before testing. After this period of time, the re blanket shail not be exposed to a dinerent atmosphere for more than 5 mi

35、n. A6 The fie blankets shall be stored for testing in their containem or stowage position for a minimum of 24 h immediately prior to testing. Annex B (normative) Electrical resistance test B.l Principle The electrid resistance of the blanket fabric is measured between a negative eleclmde formed by a

36、 metai table top and positive electrode formed by a fiat rectangular conducting plate. B.2 Apparatus B.2.1 Tdk, with metai top to be negative electrode. B.2.2 Megohmeer 500 V d.c. B.2.3 fit conducting rectangular plute, 450 mm X 150 mm incorporating an insdated handle and having a total mas of (5,O

37、f 0,26) kg. B.3 Procedure Arrange the apparatus as shown in fgure B.l. Lay the blanket flat on the table and measure its electrical resistance using the megohmeter in accordance with the manufacturers hsbuctions. Move the electrode and blanket as necessary to test the whole of the blanket. NOTE. A s

38、talliless steel plate wiii be aequate. Annex C (normative) Fire performance test NOTE. Atention is drawn to the necessity for taking precautions to safeguard the health of personnel conducting the test against the risk of re, spillage of the hot oil and the inhalation of smoke or toxic products of c

39、ombustion. C.l Materials and apparatus C.l.l M. The fuel shall be an edible cooking oil, free from additives, with an auto-ignition temperature in the range of 350 OC to 370 OC. 3 1 of fresh fuel shall be used for each test. NOTE. Edible Soya bean oil which conforms to CODEX STAN 20-1981 or a Rapese

40、ed oil which conforms to CODEX STAN 241981.) C.1.2 Fue+? trug of internal diameter (345f5) mm and depth (100 f 5) mm, and free from residue from previous tests. C.1.3 Tdk, 0,8 m high, and wer than the fire blanket size. C.1.4 Tray support stand, see figure C.1. C.2 Procedure C.2.1 Place the test tra

41、y cenWy on the tray support stand, which shal itself be placed on the table equidistant from two opposite sides, and so that the distance from one of the other sides to the far edge of the tray is (650 f 5) mm. See figure C.1. C.2.2 The fire performance test shall be conducted in a room free from dr

42、aughts, and with sufficient ventilation to allow the fire to develop freely and to remove products of combustion. The ambient temperature shall be between O “C and 30 OC. C.2.3 Place the fuel in the tray and, using a gas burner centdly positioned under the m, heat the oil so that its temperature, me

43、asured centsally, increases at about 10 “CM and self-ignites wihh 25 min to 35 min Turn off the gas supply. Allow the h-e to burn freely for 2 min after ignition, and then position the re blanket fully opened over the tray, so that the centre point of the fire blanket is close to the centre of the t

44、ray. Subsequently aust the position of the blanket as seems necessary from any side of the table. Remove the blanket 17 min after ignition and observe whether the fire is extinguished. The fire is considered to be extinguished if there are: - no visible flames after removai of the blanket; and - no

45、reignition within 3 min of removal of the blanket. Some fuel shail remain at the end of the test, Le. the fire shall be extjnguished and not merely starved of fuel. Annex D (informative) Bibliography CODEX STAN: 20-1981 CODEX STAN: 24-1981 Codex standard for edible Soya Bean oil Codex standard for R

46、apeseed oil 1 Published by the Joint Food and Agricuitud Organization of the United Nationdworld Health Organization, Codex Aiimentarius Commission, Via Del Terme Di Caracalla 1-001 Roma, Italy. O BSI 1997 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesPage

47、6 EN 1869 : 1997 O BSI 1997 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTD-BSI BS EN LBbS-ENGL 1797 Lb24bbS Ob340b3 Tb2 Page 6 EN 1869 : 1997 I I CI 008 J O BSI 1997 COPYRIGHT European Committee for StandardizationLicensed by Information Handling Service

48、sBS EN 1869 : 1997 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on sandards in Europe and at the international level. It is incorporated by Royal Charter. Contrac

49、t requirements A British Standard does not purport to include ail the necessary provisions of a contract. Users of British standards are responsible for their correct application. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quaiity of our products and services. We would be grateful if anyone nding an inaccuracy or ambiguity while using this British Standar