1、BRITISH STANDARD Flexible sheets for iW EN 19282000 waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of watertightness The European Standard EN 192232000 has the status of a British Standard ICs 76.140; 83.140.10; 91.100.50 NO COPYING WITHOUT BSI PERMISSION E
2、XCEPT AS PERMI“ED BY COPYRIGHT LAW STD-BSI BS EN 1728-ENGL 2000 H 1b2Ybb7 O8b88bb IT0 = BS EN 1928:2000 direction of the Sector Committee for Building and Cid Engineering, was published under the authority of the Standards Committee and comes into effect on 16 September 2000 Amd. No. O BSI 09-2000 N
3、ational foreword Date Comments This British Standard is the official English language version of EN 19282000. The UK participation in its preparation was entrusted by Technical Committee W54.6, Flexible sheets for waterproofing, to Subcommittee B/546/1, Bituminous roofing felts,which has the respons
4、ibility to: - aid enquirers to understand the text; - present to the responsible European committee any enquiries on the - monitor related intemational and European developments and promulgate interpretation, or proposals for change, and keep the UK interests informed; them in the UK. A list of orga
5、nizations represented on this subcommittee can be obtained on request to its secrem. Cross-references The British Standards which implement intedonai or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled ?Intedonal Standards Corr
6、espondence Index?, or by using the ?Find? facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does n
7、ot of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 8, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued
8、ISBN O 580 36351 1 STD=BSI BS EN L728-ENGL 2000 Lb2Libb7 OBb8Bb7 O37 EUROPEAN STANDARD NORME EUROPEENNE EUROPISCHE NORM EN 1928 March 2000 ICs 91.100.50 English version Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of watertightness Feu
9、illes souples dtanchi - Feuilles dtanchi de toiture biumineuses, plastiques et lastomres - Dtermination de ltanchit leau Abdichtungsbahnen - Blumen-, Kunststoff- und Elastomerbahnen fcir Dachabdichtungen - Bestimmung der Wasserdichtheit This European Standard was approved by CEN on 17 February 2000.
10、 CEN members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Uptodate lists and bibliographical references concerning sich national standards may be obtained on ap
11、plication to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by tmslation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has
12、the same status as he official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMilTEF
13、, FOR STANDARDIZATION EUROPAISCHES KOMITEE FUR NORMUNG COMIT EUROPBEN DE NORMALISATION Central Secretariat: rue de Stassart, 36 B-1050 Brussels Q 2000 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1928:2000 E STD-BSI BS EN L728-E
14、NGL 2000 Lb24bb7 OAbAb T73 W Page 2 EN 1928:2000 Contents Page Foreword 3 Introduction - 3 1 Scope - . 3 2 Normative references . - 3 3 Definitions . 3 4 Principle . 4 5 Apparatus . 4 6 Sampling 7 7 Test specimens . - . 7 8 Procedure . 7 9 Expression of results and precision . 8 10 Test report 8 Bib
15、liography 8 . Q BSI 09-2000 STD-BSI BS EN 1928-ENGL 2000 m lb2Libb OBbAAb9 9OT Page 3 EN 1928:2000 Foreword This European Standard has been prepared by Technical Committee CENTTC 254, Flexible sheets for waterproofing, the Secretariat of which is held by BSI. This European Standard shall be given th
16、e status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2000, and conflicting national standards shall be withdrawn at the latest by September 2000. According to the CENEENELEC Internal Regulations, the national standards organization
17、s of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Introduction This standard h
18、as been prepared by the Technical Committee CENTTC 254 to determine the watertightness of sheets for waterproofing. This standard has been prepared for applications in roofing but it may also be used in other areas where it is relevant. This standard is intended for characterization of flexible shee
19、ts for waterproofing as manufactured or supplied before use. This standard relates exclusively to products and not to waterproofing membrane systems composed of such products and installed in the works. 1 Scope This European Standard applies to bitumen, plastic and rubber sheets for roof waterproofi
20、ng and specifies procedures for determining the watertightness, .e. the resistance to ponding water or to hydraulc pressure absorbed by a limited part of the surface, of factory made products. This standard may also be used in other waterproofing areas. 2 Normative references This European Standard
21、incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of these publications apply to this draft
22、European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. prEN 13416:1999 Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Rules for sampling. 3 Definitions
23、 For the purpose of this standard, the following definitions apply. 3.1 upper side: the upperside of the sheets, as laid, usually the inside of the roll 3.2 watertightness: condition of flexible sheet for waterproofing if: a) b) in case of method A: no discoloration is observed of the filter paper a
24、bove the surface of a test specimen at the applied water pressure during the total test period in case of method B: the applied maximum pressure does not drop by more than 5 % of the initial value Q BSI 09-2000 Page 4 EN 1928:2000 4 Principle Due to the nature of the bitumen, plastic or rubber sheet
25、s concerned, the test procedure given in this standard consists of two methods. 4.1 Method A Test procedure for sheets intended for use in low pressure application, e.g. roofing, underlay, vapour control layer. The specimen is subjected to a pressure up to 60 kPa for 24 h. 4.2 Method B Test procedur
26、e for sheets intended for use in high pressure application, e.g. special roofs, tunnelling and tanking. Submission of a test specimen to a specified water pressure for 24 h against a disk containing four slots of specified form and dimensions. The test specimen is observed to establish whether it re
27、mains watertight. 5 Apparatus 5.1 MethodA A cylindrical metal flanged box, with a 150 mm diameter aperture, is connected to an open ended pipe or vessel which rises to a height of not less than 1 m, generally as shown in Figure 1. Q BSI 09-2000 Page 5 EN 1928:2000 Key 1 2 3 4 5 6 7 8 9 10 11 12 13 D
28、imensions in millimetres Lower rubber sealing gasket Test specimen inserted such that the surface normally exposed to the weatherhater will be in contact with the water under test Laboratory filter paper Moisture indicating mixture uniformly spread over surface of test specimen. A moisture passing t
29、hrough the test specimen is readily detected using an indicator consisting of a mixture of fine white (icing) sugar (993 %) and methylene blue dye (03 %) sieved over a 0,074 mm mesh and dried over calcium chloride in a desiccator Laboratory filter paper Circular ordinary window glass sheet - 5 mrn t
30、hick for pressure of water ; 1 O kPa - 8 mm thick for pressure of water 60 kPa Upper rubber sealing gasket Steel clamping ring Wing nuts Air exhaust valve Water inlet valve Water supply and draining valve Means to apply and control pressure up to 60 kPa Figure 1 - Apparatus for watertightness test a
31、t low pressures O BSI 09-2000 Page 6 EN 1928:2000 5.2 Method B The apparatus consists of a device (see Figures 2 and 3) by which a pressure can be applied to one side of a test specimen. 2 3 Key 1 Slots 2 Cover 3 Test specimen 4 Hydrostatic pressure 5 Observation gap 6 Slotted plate Figure 3 - Devic
32、e for the slot pressure test: Sketch of the cover Figure 2 - Slot pressure testing device for watertightness at high pressures The test specimen is covered by a circular disk containing four slots. The form and dimensions of the slots are specified by the requirements indicated in Figure 4. i Dimens
33、ions in millimetres Key 1 2 All edges of the slotted plate are rounded to a radius of 0,5 mm approximately Longitudinal direction of the membrane Figure 4 - Slotted plate Q BSI 09-2000 Page 7 EN 1928:2000 6 Sampling Test samples shall be taken in accordance with prEN 13416:1999. 7 Test specimens 7.1
34、 Preparation The specimens shall be taken evenly distributed across the width of the sheet, the outer ones 100 mm of the edges. The longitudinal direction on the test specimens shall be marked parallel to direction of production. The number of test specimens shall be as specified in the relevant pro
35、duct standard, but shall be a minimum of three. 7.2 Dimensions of the test specimens 7.2.1 MethodA Circular test specimens with a diameter of (200 f 2) mm. 7.2.2 Method B Circular test specimens wih a diameter equal to the external diameter of the slotted plate (approximately 130 mm). 7.3 Conditioni
36、ng of test specimens The test specimens shall be stored for at least 6 h at (23 f 5) “C prior to testing. 8 Procedure 8.1 Test conditions The test shall be camed out at (23 f 5) “C. In case of dispute it shall be camed out at (23 f 2) “C and (50 f 5) % relative humidity (RH). The test pressure shall
37、 be specified in the product specification. It shall be ensured that the margins are watertight. 8.2 Procedure method A Insert the test specimen into the apparatus (5.1). Tighten the wing nuts (9) firmly onto the clamping ring. Open the valve (1 1) to let water in while valve (IO) is left open to al
38、low air to escape. Close valve (IO) once water passes through indicating that the apparatus is filled. Apply the required pressure to the upper side of the test specimen. Maintain the pressure for a period of (24 f 1) h. . Inspect the test specimen to see if there has been discoloration of the upper
39、 filter paper. 8.3 Procedure method B Fill the apparatus in accordance with Figure 2 with water until overflowing. Purge the water line thoroughly. Place the test specimen with its upper side downwards in the apparatus and cover with the specified slotted plate, one of the slots (see Figure 4) being
40、 parallel to the longitudinal direction of the sheet. Place the cover and progressively tighten until the specimen is tightly in place. Dry the non-exposed side of the specimen with a cloth or with compressed air. Pressurize progressively to the specified test pressure. Once the test pressure is rea
41、ched, maintain the pressure for a period of (24 f I) h. Observe the watertightness of the test specimen after the testing time (sudden pressure drop or presence of water on the non-exposed face of the test specimen). Q BSI 09-2000 Page 8 EN 1928:2000 9 Expression of results and precision 9.1 Express
42、ion of results 9.1.1 Method A Any specimen with evidence of water penetration through to the upper filter paper is deemed to have failed the test. The sheet is deemed to be watertight when all specimens pass the test. 9.1.2 Method B The watertightness test is considered passed if all test specimens
43、remain watertight after the specified testing time. 9.2 Precision Precision is not specified by this standard. NOTE No report on inter-laboratory tests of repeatability and reproducibility is available. 10 Test report The test report shall include at least the following information: a) all details n
44、ecessary to identify the product tested: b) a reference to this European Standard (EN 1928) and any deviation from it; c) information on sampling in accordance with clause 6; d) details of preparation of test specimens in accordance with clause 7; e) test procedure indicating method A or B used, inc
45、luding the test pressure and any deviation: 9 the test results in accordance with clause 9: g) the dates of the tests. Bibliography I UEAtc M.0.A.T No. 27:1983 “General Directive for the Assessment of Roof Waterproofing Systems“ 2 DIN 16726:1986-12 Kunststoff-Dachbahnen, Kunststoff-Dichtungsbahnen,
46、Prfung (Plastic roofing sheets - plastic sheets for waterproofing - testing) 8 BSI 09-2000 BS EN 19282000 BSI 389 Chiswick High Road London w4 4AL STDOBSI BS EN L928-ENGL 2000 M Lb2ilbb9 0868875 103 M BSI - British Standards Institution BSI is the independent national body responsible for preparing
47、British Stanhds. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It i
48、s the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inacuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front
49、cover. Tel: O20 8996 9ooo. Fax 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for ali BSI, intemational and foreign standards publications should be addressed to Customer Services. Tel: O20 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of thcse that have been published as British Standards, unless otherwise requested. Information on st
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1