EN 1969-2000 en Surfaces for Sports Areas - Determination of Thickness of Synthetic Sports Surfaces《运动场表面 合成运动场表面厚度的测定》.pdf

1、STD-BSI BS EN LSbS-ENGL 2000 E lb2Vbb9 0859313 879 BRITISH STANDARD Surfaces for sports areas - Determination of thickness of synthetic sports surfaces The European Standard EN 19692000 has the status of a British Standard ICs 97.150 97.220.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY

2、 COPYRIGHT LAW CS EN 969:2000 STD-BSI BS EN LSbS-ENGL 2000 m lb2LIbbS 085LI314 720 m BS EN 1969:ZOOO National foreword This British Standard is the official English hguage version of EN 19692000. EN 19692000 is one of a package of standards being produced by CEN/TC 217. On publication of the entire

3、package, BS 7044 will be superseded and withdrawn. The UK participation in its preparation was entrusted to Technical Committee PRV57, Surfaces for sports areas, which has the responsibility to: - aid enquirers to understand the text, - present to the responsible European committee any enquiries on

4、the - monitor related internationai and European developments and promulgate interpretation, or proposals for change, and keep the UK interests informed; them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British st

5、andards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Eleclronic Catalogue. A British Stand

6、ard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover,

7、an inside front cover, the EN title page, pages 2 to 4, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. This British Standard, having been prepared under the direction of the Sector Committee for Materials and Ch

8、emicals, was published under the authority of the Standards Committee and comes into effect on 16 June 2000 Amendments issued since publication O BSI W200 ISBN O 580 34056 2 STD-BSI BS EN LSbS-ENGL 2000 Lb2LibbS 085Li315 bb7 EIUROPEAN SlXNDm EN 1969 NORME EUROPENNE EuROP 97.220.10 English version Su

9、rfhces for sports aras - Determination of thickness of synthetic sports !%Irface Sols sportifs - Dkrmhation de lpaisseur des sols sport 2 Apparatus 2.1 Method A 2.1.1 Plaw refmeme plate 2.1.2 Thiclcness gauge, with a 0,Ol mm accuracy dial, a plunger with a flat measuring surface of 4 mm f 0,l mm dia

10、meter and a measurement force between 0,s N and 1,0 N. 2.2 Method B 2.2.1 Thiclmess measuring probe, comprising three Mended, steel probes, circular in section, approximately 2 mm in diameter, set in a triangular pattern between 15 mm and 20 mm apart, which can be driven into a surface under test in

11、 such a manner that the minimum depth of penemon from the upper surface of the material under test can be measured by means of a sliding, calibrated barrel, having a flat circular base of 25 mm to 30 mm in diameter (see Figure 1). Dimensions in millimetres Figure 1 - Example of an apparatus to measu

12、re thickness by method B o BSI 06-2000 STD-BSI BS EN LSbS-ENGL 2000 PIC1 Lb24bb9 085Li318 37b W Page 4 EN 1969:2000 3 Bst specimens for methodA 3.1 Preparation Remove a core of diasneter 20 mm to 25 mm from the surface. If necessary, gently abrade the upper and lower surfaces of the core with grade

13、60 abrasive paper until the surface area ground is approximately 50 % of the total surface area 3.2 Number of test specimens Prepare a minimum of five test specimens. 4 Procedure 4.1 Test conditions Unless stated otherwise in the manufacturers specifcation, carry out the tests at 23 OC f 2 OC and 50

14、 % f 5 % relative humidity. 4.2 MethodA 4.2.1 Total thickness Set the plunger of the thickness gauge directly on the plane reference plate. Record the reading on the dial (zero reading). Place the prepared core between plunger and plate. Record the reading on the dial (measurement reading 1). 4.2.2

15、Layer thickness Gently abrade the top layer with grade 60 abrasive paper until approximately 50 % of the bottom layer is visible. Replace the core between plunger and plate and record the reading on the dial (measurement reading 2). 4.3 Method B 4.3.1 Force the thickness measuring probe into the sur

16、face under test, using hand pressure, until one or more of the steel probes comes into contact with the Substrate. NOTE Care is required when testing surfaces instailed over macadam or asphalt, to ensure that the probes do not penetrate any soft areas or voids in the substrate. Without moving the pr

17、obes, adjust the sliding bmel until it is in contact with the upper surface of the surface under test, and read off the thickness from the calibrated barrel. 4.3.2 If necessary, make allowance for any surface texture which may be present by laying a reference sample with an identical surface texture

18、 over a steel plate, placed adjacent to the test area, and measure the thickness as given in 4.3.1. Remeasure the thickness of the reference sample as given in 4.2. 5 Calculation and expression of results 6.1 Method A Calculate the total thickness and layer thickness of each test specimen as follows

19、: Total thickness: Total thickness, in millimetres, is given by measurement reading 1 minus zero reading. Layer thickness: Layer thickness, in miliimetres, is given by total thickness minus measurement reading 2. Express the results to the nearest 0,i mm. 6.2 Method B Where necessary, apply the foll

20、owing correction factor to all individual measurements: Correction factor, in miliimetres, is given by thickness of the reference sample using method B, in millimetres, minus thickness of the reference sample using method A, in millimetres. Express results to the nearest 0,5 mm. 6 Test report The te

21、st report shall contain the following: a) the number and date of this European Standard, i.e. prEN 19691999; b) the nature and designation of the material includmg, for in-situ measurements, a plan of the testjng sites; c) the test conditions, including site weather conditions for in4tu measurement;

22、 d) the individual test results and their average; e) the date of the test and the reference number. o BSI 06-2000 BS EN 19692000 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents

23、 the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to

24、 improve the quality of our products and services. We would be grateful if anyone nding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel 020 8996 9OOO. Fax

25、: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for ail BSI, international and foreign standards publications should be adclressed to Customer Services. Tel 0

26、20 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implemenation of those that have been published as British Standads, unless otherwise requested. Information on standards BSI provides a wide range of information on national, Euro

27、pean and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic infomation services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax. 020 8996 7048. Subscribing mem

28、bers of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Admuustsati on. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. B

29、SI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no exh-act may be reproduced, stored in a retrieval system or tsansmtted in any form or by any means - electronic, photocopyi

30、ng, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. if permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel 020 8996 7070.