EN 2044-2001 en Aerospace Series - Round Bars Drawn in Aluminium and Aluminium Alloys - Tolerance Class h 11 - Diameter 4 mm Less Than or Equal to D Less Than or Equal to 63 mm - D.pdf

1、BRITISH STANDARD AEROSPACE SERIES Round bars, drawn, in aluminium and aluminium alloys Tolerance class h 11 Diameter 4mm SD S 63rnrn Dimensions The European Standard EN 2044:2001 has the status ofa British Standard ICs 49.025.20; 49.035 BS EN 2044:2001 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PER

2、MITTED BY COPYRIGHT LAW BS EN 2044:2001 Amd. No. National foreword Date Comments This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 24 December 20

3、01 This British Standard is the official English language version of EN 2044:200 1. The UKparticipation in its preparation was entrusted to Technical Committee ACE/61, Inspection and testing requirements for aerospace metallic materials, which has the responsibility to: - - aid enquirers to understa

4、nd the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this committee

5、can be obtained on request to its secretary. Cr oss-r e fer enc e s The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by u

6、sing the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immuni

7、ty from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 5, and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. O BSI 24 December 2001 ISBN O 580 37994 9 EUROPE

8、AN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2044 December 2001 ICs 49.025.20 English version Aerospace series - Round bars, drawn, in aluminium and aluminium alloys - Tolerance class h 11 - Diameter 4 mm I D I 63 mm - Dimensions Srie arospatiale - Barres rondes, tires, en aluminium et alliages da

9、luminium - Classe de tolrance h 11 - Diamtres 4 mm s D s 63 mm - Dimensions Luft- und Raumfahrt - Rundstangen, gezogen, aus Aluminium und Aluminiumlegierungen - Toleranzklasse h 11 - Durchmesser 4 mm s D s 63 mm - Mae This European Standard was approved by CEN on 2 May 2001 CEN members are bound to

10、comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Manageme

11、nt Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the offi

12、cial versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROP

13、ISCHES KOMITEE FR NORMUNG COMIT EUROPEN DE NORMALISATION Management Centre: rue de Stassart, 36 B-1050 Brussels O 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2044:2001 E EN 2044:2001 Foreword This European Standard has bee

14、n prepared by the European Association of Aerospace Manufacturers (AECMA) . After inquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior t

15、o its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2002, and conflicting national standards shall be withdrawn at the latest by June 2002. According to the CENKENELEC

16、Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzer

17、land and the United Kingdom. 2 EN 2044:2001 O Introduction This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. 1 Scope This standard specifies the dimensions and tolerances of: Round bars,

18、drawn in aluminium and aluminium alloys Tolerance class h 11 Diameter 4 mm 6 O00 5.1.2 Length See table 3, only applicable to bars supplied in fixed lengths. Table 3 Dimensions Tolerances +6 0 + 10 0 in millimetres Nominal D 4D 6 Roundness deviation 0,038 5.2.1.2 Tolerances See table 4. 50 D 63 Tabl

19、e 4 Dimensions in millimetres 0,095 Nominal D Straightness deviation: V, per metre I Y, on any length X2 a 4D10 I To be agreed between manufacturer and purchaser 10 D 63 2 0,6 5.2.2 Roundness 5.2.2.1 Method of measurement See EN 3848. 5.2.2.2 Tolerances See table 5. 5 BS EN 2044:2001 BSI 389 Chiswic

20、k High Road Lon don w4 4AL BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Re vi si ons British Standards are updated by amendment or revision. Users

21、of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary

22、 of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standar

23、ds. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: orders&-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for inte

24、rnational standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its T

25、echnical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 71 11. Fax: +44 (0)20 8996 7048. Email: infomi-. Subscribing members of BSI are kept up to date

26、with standards developments and receive substantial discounts on the purchase price of standards. For details ofthese and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 700 1. Email: membershipbsi-. Information regarding online access to British Stand

27、ards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, ofthe publications of the international standardization bod

28、ies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise -without prior written permission from BSI. This does not preclude the f

29、ree use, in the course of implementing the standard, ofnecessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then the prior written permission ofBSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyright&-.