1、BRITISH STANDARD AEROSPACE SERIES BSEN 2070-6:1991 Specification for Aluminium and aluminium alloy wrought products Technical specification Part 6: Rivet wire This European Standard EN2070-6:1989 has the status of a British Standard.BSEN2070-6:1991 This British Standard was published under the autho
2、rityofthe Board of BSIandcomes into effecton 31December1990 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference ACE/61 Draft for comment 88/72194 DC ISBN 0 580 19079 X Cooperating organizations The European Committee for Standardization, under whose supe
3、rvision this European Standard was prepared, comprises the national standards organizations of the following Western European countries. Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normalisation Denmark Dansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y. Fra
4、nce Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland Ireland National Standards Authority of Ireland Italy Ente Nazionale Italiano di Unificazione Luxemburg Inspection du Trava
5、il et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Asociacin Espaola de Normalizacin y Certificacin Sweden Standardiseringskommissionen i Sverige Switzerland Association suisse de normalisation United Kin
6、gdom British Standards Institution Amendments issued since publication Amd. No. Date of issue CommentsBSEN2070-6:1991 BSI 12-1999 i Contents Page Cooperating organizations Inside front cover National foreword ii Brief history 2 Text of EN 2070-6 3 National appendix A Inside back cover National appen
7、dix B Inside back coverBSEN2070-6:1991 ii BSI 12-1999 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN2070 “Aerospace series. Aluminium and aluminium alloy wrought products. Technical s
8、pecification.” Part 6: “Rivet wire”, published by the European Committee for Standardization (CEN). EN2070-6 was produced as a result of international discussion in which the UK took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of B
9、ritish Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 4, an inside back
10、cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2070-6 December 1989 UDC 669.71.018.26-427:620.1:629.7 Ke
11、y words: Aircraft industry, rolled products, semi-finished products, aluminium, aluminium alloys, wire, defects, mechanical tests, cold-working English version Aerospace series Aluminium and aluminium alloy wrought products Technical specification Part 6: Rivet wire Srie arospatiale Demi-produits co
12、rroys en aluminium et alliages daluminium Spcification technique Partie 6: Fils rivets Luft- und Raumfahrt Halbzeug aus Aluminium und Aluminium-Knetlegierungen Technische Lieferbedingungen Teil 6: Nietdrhte This European Standard was accepted by CEN on1988-07-20. CEN members are bound to comply with
13、 the requirements of CEN Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Centra
14、l Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to CEN Central Secretariat has the same status as th
15、e official versions. CEN members are the national standards organizations of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxemburg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit
16、 Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels CEN 1989 Copyright reserved to all CEN members Ref. No. EN 2070-6:1989 EEN2070-6:1989 BSI 12-1999 2 Brief history This European Standard has been prepared by the European Association of
17、Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this Standard has successively received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. Acc
18、ording to the Common CEN/CENELEC Rules, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxemburg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. Contents Page B
19、rief history 2 1 Scope and field of application 3 2 References 3 3 Batch size 3 4 Dimensions 3 5 External defects 3 6 Mechanical testing 3 7 Suitability for cold heading 3 8 Special tests 3 9 Marking 3 Table 1 Summary of requirements for rivet wire 4EN2070-6:1989 BSI 12-1999 3 1 Scope and field of a
20、pplication The present standard specifies the particular requirements for aluminium and aluminium alloy wire intended for rivet manufacture. This standard shall be used in conjunction with EN2070-1. 2 References ISO/R 2101:1971, Aluminium and aluminium alloys Shear test for rivet wire and rivets. EN
21、 2002-1, Aerospace series Test methods for metallic materials Part 1: Tensile test at ambient temperature 1) . EN 2070-1, Aerospace series Aluminium and aluminium alloy wrought products Technical specification Part 1: General requirements. 3 Batch size The maximum weight of the batch shall be500kg.
22、4 Dimensions Dimensions and tolerances shall conform to the relevant semi-finished product standard. The frequency of examination adopted by the manufacturer shall be sufficient to permit him to certify compliance with the requirements. 5 External defects Visual surface inspection shall be carried o
23、ut at a frequency sufficient to permit the manufacturer to certify compliance with the requirements of this clause. The wire shall be clean and smooth and free from defects such as drawing scores, die pick-up, indentations, cracks or corrosion considered harmful to its use. 6 Mechanical testing Wire
24、 shall be submitted to either the tensile test in accordance with EN2002-1 or the shear test, in accordance with ISO/R2101 at the option of the manufacturer in the condition of supply and/or use as required by the material standard. The frequency of testing is given inTable 1. The values obtained sh
25、all meet the requirements of the material standard. Regardless of the type of test carried out, the wire shall be capable of meeting the tensile test and shear test values required by the material standard. Re-testing procedure for shear testing shall be as EN2070-1 “Tensile re-tests”. 7 Suitability
26、 for cold heading The quality of the wire shall be such that cold headed rivet shapes can be produced without developing cracks, or general or localized excessive grain growth after heat treatment. Evaluation of forming capability shall be accomplished, for example, by some type of torsion test or a
27、 cold heading test or such other tests as may be agreed between the manufacturer and purchaser. The frequency of examination adopted by the manufacturer shall be sufficient to permit him to certify compliance with the requirements. 8 Special tests Special tests and inspections may be required by the
28、 purchaser. In such cases, after agreement between purchaser and manufacturer, nature of the tests, methods, number and acceptance standards shall be specified on the order or in the inspection schedule. 9 Marking A durable label attached to each coil or bundle shall bear the information required by
29、 EN2070-1 (Clause10.1) in addition to the following: wire diameter, weight of coil or bundle in kg. If special tests in accordance with clause8 are required the marking shall be defined and shall reflect these extra requirements. The frequency of examination adopted by the manufacturer shall be suff
30、icient to permit him to certify compliance with the requirements. 1) In preparationEN 2070-6:1989 4 BSI 12-1999 Table 1 Summary of requirements for rivet wire Requirements Clause Product Inspection/Testing Method Standard Frequency Dimensions 4 All products See clause 4 External defects 5 All produc
31、ts Visual See clause 5 Mechanical tests 6 Products in the condition: H. aor O a Tensile or shear EN 2002-1 or ISO/R 2101 2 test per batch (from different coils or bundles if more than one). T. a Tensile or shear EN 2002-1 or ISO/R 2101 Suitability for cold heading 7 All products See clause 7 Marking
32、 9 All products Visual See clause 9 a Aluminum Association designation.BS EN2070-6:1991 BSI 12-1999 National appendix A The United Kingdom participation in the preparation of this European Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/61 upon w
33、hich the following bodies were represented: Aluminium Federation British Forging Industry Association British Investment Casting Trade Association British Steel Industry Copper Development Association Department of Trade (National Physical Laboratory) Light Metal Founders Association Ministry of Def
34、ence Society of British Aerospace Companies Limited National appendix B The British Standards corresponding to the European Standards referred to in the text are identical in number and title with those given in clause2, with the exception of ISO/R2101 for which there is no corresponding British Sta
35、ndard.BS EN 2070-6:1991 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisio
36、ns BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambigui
37、ty while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automati
38、cally receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI impl
39、ementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic in
40、formation services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards
41、. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the
42、 Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementin
43、g the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1