EN 2078-2001 en Aerospace Series - Metallic Materials - Manufacturing Schedule Inspection Schedule Inspection and Test Report - Definition General Principles Preparation and Approv.pdf

1、BRITISH STANDARD AEROSPACE SERIES Metallic materials Manufacturing schedule, inspection schedule, inspection and test report Definition, general 0 0 i 0 principles, preparation and approval The European Standard EN 2078:2001 has the status of a British Standard ICs 49.025 BS EN 2078:2002 Wk present

2、to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this committee can be obtained on re

3、quest to its secretary. Cr oss-r e fer enc e s The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled ?International Standards Correspondence Index?, or by using the ?Find? facil

4、ity of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligat

5、ions. This British Standard. having - been prepared under the direction of the Engineering Summary Of pages Sector Policv and Stratew This document comprises a front cover, an inside front cover, the EN title page, -_ Committee, was published pages 2 to 5. and a back cover. under the authority of th

6、e Standards policy and Strategy Committee on 09 January 2002 The BSI copyright date displayed in this document indicates when the document was last issued. O BSI 09 January 2002 ISBN O 580 38807 7 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2078 December 2001 ICs 49.025.05; 49.025.15 Supers

7、edes EN 2078:1993 English version Aerospace series - Metallic materials - Manufacturing schedule, inspection schedule, inspection and test report - Definition, general principles, preparation and approval Srie arospatiale - Matriaux mtalliques - Fiche de fabrication, fiche dessais, rapport de contrl

8、e et dessais - Dfinition, principes gnraux, prparation et approbation Luft- und Raumfahrt - Metallische Werkstoffe - Fertigungsplan, Prfanweisung, Abnahmeprfzeugnis - Definition, allgemeine Grundstze, Aufstellung und Genehmigung This European Standard was approved by CEN on 2 May 2001. CEN members a

9、re bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to

10、the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status

11、 as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDI

12、ZATION EUROPISCHES KOMITEE FR NORMUNG COMIT EUROPEN DE NORMALISATION Management Centre: rue de Stassart, 36 B-1050 Brussels O 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2078:2001 E EN 2078:2001 (E) Foreword This European

13、Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA) . This European Standard supersedes EN 2078:1993. After inquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and

14、 the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2002, and conflicting national standards shall be wi

15、thdrawn at the latest by June 2002. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, L

16、uxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 2 EN 2078:2001 (E) O Introduction This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. 1 Scope Th

17、is standard defines the manufacturing schedule, inspection schedule and inspection and test report for EN aerospace metallic semi-finished products. It also specifies the general principles, preparation and approval of these documents. It shall be used with the relevant semi-finished product definit

18、ion documents (level 3) defined in EN 4258. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated ref

19、erences, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies. EN 2000 Aerospace series - Quality assurance - EN aero

20、space products - Approval of the quality system of manufacturers EN 3042 Aerospace series - Quality assurance - EN aerospace products - Qualification procedures EN 4258 Aerospace series - Metallic materials - General organization of standardization - Links between types of EN standards and their use

21、 EN 4259 Aerospace series - Metallic materials - Definition of general terms 1) EN 10204 Metallic products - Types of inspection documents 3 Definitions For the purposes of this standard, the following definitions apply: 3.1 Design Authority See EN 4259. 1) Published as AECMA Prestandard at the date

22、 of publication of this standard 3 EN 2078:2001 (E) 3.2 Manufacturing schedule Document specifying the actual procedures to be followed in the manufacture of an EN aerospace metallic semi-finished product. NOTE The manufacturing schedule is the response of the manufacturer to orders placed by any pu

23、rchaser. 3.3 Inspection schedule Document specifying additional inspection and/or testing requirements to those of the applicable EN aerospace standard for that semi-finished product. 3.4 Inspection and test report Document giving the results of all inspection and testing carried out on the semi-fin

24、ished product in accordance with the applicable EN aerospace semi-finished product standard and any additional requirements specified on the drawing, order or inspection schedule. 4 Manufacturing schedule 4.1 General principles The preparation of a manufacturing schedule is a mandatory requirement f

25、or semi-finished products qualification in accordance with EN 3042. The preparation of the manufacturing schedule is under the responsibility of the manufacturer. This document is his property. On written request, the purchaser is entitled to collaborate in the drafting. The manufacturing schedule i

26、s used as the reference document for semi-finished product qualification, under the confidentiality conditions defined in EN 2000. 4.2 Preparation The manufacturing schedule shall describe the manufacturing stages (including inspection and testing procedures) for the semi-finished product to be manu

27、factured, from the acquisition of raw materials through to the storage/delivery of the manufactured semi-finished product. 4.3 Approval 4.3.1 In it ia1 approval The manufacturing schedule shall be approved by the manufacturer in accordance with the internal procedures defined in his quality assuranc

28、e system, as required by EN 2000. Where the manufacturing schedule has been defined in collaboration with the purchaser on written request and/or has been verified by means of pre-production parts, it shall, additionally, be approved by the Design Authority of the purchaser. NOTE In special cases, t

29、he manufacturing schedule can be sealed on purchasers written instructions. 4 EN 2078:2001 (E) 4.3.2 Monitoring of subsequent changes Changes which may significantly affect the quality of the semi-finished product shall be submitted for the written approval of the purchaser. After this approval, the

30、 manufacturer shall inform the Qualification Authority of the agreed changes. The Qualification Authority may record these changes (as an addition to the semi- finished product qualification file) or call for supplementary tests or for a new qualification. Where the manufacturing schedule is sealed,

31、 any change shall be submitted for the purchasers written approval prior to implementation. 5 Inspection schedule 5.1 General principles The inspection schedule is used in the case of semi-finished products the characteristics of which cannot be completely specified by EN aerospace standards, typica

32、lly forgings and castings. The preparation of the inspection schedule is under the responsibility of the purchaser. The inspection schedule is implemented by the manufacturer but remains the purchasers property. 5.2 Preparation The inspection schedule shall specify additional requirements for inspec

33、tion and testing not defined in the standards appearing on the order. It shall be linked to the reference of the semi-finished product drawings. 5.3 Approval The inspection schedule shall be approved in accordance with the internal procedures defined in the purchasers quality assurance system, as re

34、quired by EN 2000. 6 Inspection and test report 6.1 General principles An inspection and test report shall be provided with each semi-finished product delivery. The preparation of the inspection and test report is under the responsibility of the manufacturer. This report supports the inspection docu

35、ment (see EN 10204) required on the order. 6.2 Preparation The inspection and test report shall give the results of the release inspection and/or testing in accordance with the relevant standards and, where relevant, purchasers additional instructions as stated in the order, drawing and inspection s

36、chedule. 6.3 Approval The inspection and test report shall be approved in accordance with internal procedures defined in the manufacturers quality assurance system as required by EN 2000. 5 BS EN 2078:2002 BSI 389 Chiswick High Road Lon don w4 4AL BSI is the independent national body responsible for

37、 preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Re vi si ons British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments o

38、r editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on

39、the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards pu

40、blications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: orders&-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those

41、 that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services

42、 are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 71 11. Fax: +44 (0)20 8996 7048. Email: infomi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase p

43、rice of standards. For details ofthese and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 700 1. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further inform

44、ation about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, ofthe publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no e

45、xtract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise -without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, ofnecessary details such a

46、s symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then the prior written permission ofBSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyright&-.