EN 2162-1-1996 en Technical Product Documentation - Springs - Part 1 Simplified Representation《技术产品文献 弹簧 第1部分 简化表示法(ISO 2162-1-1993)》.pdf

1、BRITISH STANDARD BS EN ISO 2162-1:1996 BS 308-1.17: 1996 Technical product documentation Springs Part 1: Simplified representation The European Standard EN ISO 2162-1:1996 has the status of a British Standard ICS 01.100.20; 21.160BS EN ISO 2162-1:1996 This British Standard, having been prepared unde

2、r the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes intoeffect on 15 November 1996 BSI 10-1998 The following BSI references relate to the work on this standard: Committee reference TDE/4 Draft announced in BSI News ISBN 0 580 26331 2 Co

3、mmittees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee TDE/4, Engineering drawing practice, upon which the following bodies were represented: Atomic Weapons Establishment British Gas plc British Standards Society Drawing Office Ma

4、terial Manufacturers and Dealers Association Electricity Association Gauge and Tools Makers Association HEVAC Association Institution of Chemical Engineers Institution of Engineering Designers Power Generation Contractors Association Society of British Aerospace Companies Ltd. University of Warwick

5、Amendments issued since publication Amd. No. Date CommentsBSENISO2162-1:1996 BSI 10-1998 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 1 Scope 3 2 Normative references 3 3 General 3 4 Helical compression springs 3 5 Helical extension springs 5 6 Torsion sp

6、rings 5 7 Disc springs (Belleville) 6 8 Spiral springs 6 9 Leaf springs 7 Annex ZA (normative) Normative references to international publicationswiththeir relevant European publications Inside back coverBS EN ISO 2162-1:1996 ii BSI 10-1998 National foreword This British Standard has been prepared by

7、 Technical Committee TDE/4 and is the English language version of EN ISO 2162-1:1996 Technical product documentation Springs Part 1: Simplified representation, published by the European Committee for Standardization (CEN). It is identical with ISO 2162-1:1993 published by the International Organizat

8、ion for Standardization (ISO). This British Standard partially supersedes BS 308-1. It is envisaged that when the full range of European Standards on technical drawing is implemented BS 308 will be withdrawn. A British Standard does not purport to include all the necessary provisions of a contract.

9、Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-reference Publication referred to Corresponding British Standard BS EN ISO 2162 Technical product documentation Springs EN ISO

10、 2162-2:1996 BS EN ISO 2162-2:1996 Presentation of data for cylindrical helical compression springs (ISO 2162-2:1993) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 8, an inside back cover and a back cover. This standard ha

11、s been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2162-1 July 1996 ICS 01.100.20; 20.160 Descriptors: Drawings, technical drawings, graphic methods,

12、 springs English version Technical product documentation Springs Part 1: Simplified representation (ISO 2162-1:1993) Documentation technique de produits Ressorts Partie 1: Reprsentation simplifie (ISO 2162-1:1993) Technische Produktdokumentation Federn Teil 1: Vereinfachte Darstellung (ISO 2162-1:19

13、93) This European Standard was approved by CEN on 1996-03-02. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical refe

14、rences concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member i

15、nto its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,

16、Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CEN members Ref. No. EN ISO 2162-1:1996 EEN ISO 2162-1:1996 2 BSI 10-1998 Forew

17、ord The text of the International Standard from Technical Committee ISO/TC 10, Technical drawings, product definition and related documentation, of the International Organization for Standardization (ISO) has been taken over as a European Standard by the Technical Board of CEN. This European Standar

18、d shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 1997, and conflicting national standards shall be withdrawn at the latest by January 1997. According to the CEN/CENELEC Internal Regulations, the national standa

19、rds organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. NOTENormative references to

20、International Standards are listed in annex ZA (normative).ENISO2162-1:1996 BSI 10-1998 3 1 Scope This part of ISO 2162 gives rules for the simplified representation of compression, extension, torsion, disc, spiral and leaf springs on technical drawings. 2 Normative references The following standard

21、s contain provisions which, through reference in this text, constitute provisions of this part of ISO 2162. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO 2162 are encouraged to investigate the

22、 possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 2162-2:1993, Technical product documentation Springs Part 2: Presentation of data for cylindrical helical compression springs.

23、 ISO 5261:1981, Technical drawings for structural metal work. 3 General In simplified representations, springs are represented as follows. Coiled wire springs: by a line following the axis of the spring wire. Other types of springs: by lines showing the characteristics of the respective type of spri

24、ngs and their elements. The representations shown are examples only. 4 Helical compression springs The following requirements shall be applied for the indication of the geometrical characteristics of wiremade springs on a simplified representation. a) Cross-section of the material Cylindrical: the a

25、ppropriate graphical symbol in accordance with ISO 5261 () need not be indicated. Other than cylindrical: the appropriate graphical symbol in accordance with ISO 5261 shall be indicated (e.g. , ). b) Direction of helix Right-hand: assumed as normal and the designation RH need not be indicated. Left-

26、hand: exceptional and the designation LH 1)shall be indicated. c) Shape of ends Ground: no indication is necessary. Other than ground: the type shall be specified on the drawing, with dimensions if necessary (see ISO 2162-2). 1) In accordance with the rules given for the indication of left-hand scre

27、w threads (see ISO 5864:1978, ISO inch screw threads Allowances and tolerances, clause 11).EN ISO 2162-1:1996 4 BSI 10-1998 No. Type of spring Representation View Section Simplified 4.1 Cylindrical helical compression spring 4.2 Conical helical compression spring Combinations of cylindrical (4.1) an

28、d conical (4.2) helical compression springs. 4.3 Double-conical helical compression spring Barrel spring 4.4 Double-conical helical compression spring Waisted spring 4.5 Spring nest of, for example, two cylindrical helical compression springs 4.6 Cylindrical helical compression spring of material ha

29、ving square cross-sectionENISO2162-1:1996 BSI 10-1998 5 5 Helical extension springs The requirements for the indication of the cross-section of the material and direction of helix are identical to those given in clause 4. The shape of the ends shall be specified on the drawing, with dimensions if ne

30、cessary. The spring and its ends usually have the same diameter. 6 Torsion springs The requirements for the indication of the direction of helix and the cross-section of the material for 6.1 are identical to those given in clause 4. For 6.2 and 6.3, the cross-section of the material shall be indicat

31、ed. The shape of the ends shall be specified on the drawing, with dimensions if necessary. No. Type of spring Representation View Section Simplified 4.7 Conical helical compression spring of strip having rectangular cross-section Volute spring No. Type of spring Representation View Section Simplifie

32、d 5.1 Cylindrical helical extension spring No. Type of spring Representation View Section Simplified 6.1 Cylindrical helical torsion springEN ISO 2162-1:1996 6 BSI 10-1998 7 Disc springs (Belleville) 8 Spiral springs The cross-section of the material shall be indicated (see example in 8.1). In cases

33、 8.1 and 8.2 the shape of the ends needs to be indicated. No. Type of spring Representation View Simplified 6.2 Torsion bar spring having circular cross-section 6.3 Stacked laminated torsion bar spring of strips having rectangular cross-section No. Type of spring Representation View Section Simplifi

34、ed 7.1 Disc spring, single 7.2 Multi-disc spring (disc laminated in parallel) 7.3 Multi-disc spring (disc laminated in series) Disc spring column No. Type of spring Representation View Simplified 8.1 Spiral spring of strip having rectangular cross-sectionENISO2162-1:1996 BSI 10-1998 7 9 Leaf springs

35、 No. Type of spring Representation View Simplified 8.2 Constant force extension spring 8.3 Constant force spring A-Motor 8.4 Constant force spring B-Motor No. Type of spring Representation View Simplified 9.1 Laminated leaf spring without eyes 9.2 Laminated leaf spring with eyes 9.3 Laminated leaf s

36、pring with eyes and helper spring 9.4 Laminated leaf spring with eyes and auxiliary springEN ISO 2162-1:1996 8 BSI 10-1998 No. Type of spring Representation View Simplified 9.5 Parabolic single-leaf spring with eyes 9.6 Parabolic multi-leaf spring without eyes 9.7 Parabolic multi-leaf spring with ey

37、es 9.8 Parabolic multi-leaf spring with eyes and helper spring 9.9 Parabolic multi-leaf spring with eyes and auxiliary springENISO2162-1:1996 BSI 10-1998 9 Annex ZA (normative) Normative references to international publications with their relevant European publications This European Standard incorpo

38、rates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this Europe

39、an Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. Publication Year Title EN Year ISO 2162-2 1993 Technical product documentation Springs Part 2: Presentation of data for cylindrical helical compression

40、 springs EN ISO 2162-2 1996BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

41、| | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by ame

42、ndment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard

43、would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editi

44、ons of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that

45、 have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are

46、also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of

47、these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright,

48、 Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the stand

49、ard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.