EN 225-2-2007 en Atomizing oil burners - Oil burner pumps and oil burner motors - Connecting dimensions - Part 2 Oil burner motors《雾化油燃烧器 油燃烧器泵和油燃烧器发动机 连接尺寸 第2部分 油燃烧器发动机》.pdf

1、BRITISH STANDARDBS EN 225-2:2007Atomizing oil burners Oil burner pumps and oil burner motors Connecting dimensions Part 2: Oil burner motorsThe European Standard EN 225-2:2007 has the status of a British StandardICS 27.060.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g

2、48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 225-2:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2007 BSI 2007ISBN 978 0 580 55783 5Nationa

3、l forewordThis British Standard is the UK implementation of EN 225-2:2007. Together with BS EN 225-1:2007 it supersedes BS 799-7:1988 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee GSE/27, Automatic gas and oil burners.A list of organizations represen

4、ted on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments iss

5、ued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 225-2October 2007ICS 27.060.10English VersionAtomizing oil burners - Oil burner pumps and oil burner motors -Connecting dimensions - Part 2: Oil burner motorsBrleurs fioul pulvrisation - Pompes et moteurs po

6、urbrleurs fioul - Dimensions de liaison - Partie 2 : Moteurspour brleurs fioullzerstubungsbrenner - Anschlussmae fr lbrenner-Pumpen und lbrenner-Motore - Teil 2: lbrenner-MotoreThis European Standard was approved by CEN on 26 August 2007.CEN members are bound to comply with the CEN/CENELEC Internal

7、Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.Thi

8、s European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the

9、 national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland a

10、nd United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 225-2:200

11、7: EEN 225-2:2007 (E) 2 Contents Foreword3 1 Scope 4 2 Dimensions.4 EN 225-2:2007 (E) 3 Foreword This document (EN 225-2:2007) has been prepared by Technical Committee CEN/TC 47 “Atomizing oil burners and their components-Function-Safety-Testing”, the secretariat of which is held by DIN. This Europe

12、an Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2008, and conflicting national standards shall be withdrawn at the latest by April 2008. Attention is drawn to the possibility that some of the elements

13、of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this Europea

14、n Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Ki

15、ngdom. EN 225-2:2007 (E) 4 1 Scope This European Standard specifies the dimensions of motors for atomizing oil burners. 2 Dimensions The dimensions shall be those given in Figure 1 through Figure 3. The size 32-08 has two versions: Version A : Depth 22 mm Version B : Depth 28 mm Dimensions in millim

16、etres Key a For the possible draining away of leakage oil, four grooves, offset by 90 , shall be provided in the hub bore and on the pump seating face. Figure 1 Top view for the flange for motor connection EN 225-2:2007 (E) 5 Dimensions in millimetres Key a For the possible draining away of leakage

17、oil, four grooves, offset by 90 , shall be provided in the hub bore and on the pump seating face. Figure 2 Sectional view for the flange for motor connection Size 32-08 (version A) Table 1 Size of oil burner pumps Size of oil burner pump d1mm N7 32-08 (Version A) 32 EN 225-2:2007 (E) 6 Dimensions in

18、 millimetres Key a For the possible draining away of leakage oil, four grooves, offset by 90 , shall be provided in the hub bore and on the pump seating face. Figure 3 Sectional view for the flange for motor connection Size 32-08 (Version B) and size 54-08 Table 2 Size of oil burner pumps Size of oi

19、l burner pump d1mm N7 32-08 (version B) 32 54-08 54 blankBS EN 225-2:2007BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international lev

20、el. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grat

21、eful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual upd

22、ating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: or

23、dersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a

24、 wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (

25、0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 70

26、02. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI al

27、so holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, re

28、cording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.