EN 233-1999 0537 Wallcoverings in Roll Form - Specification for Finished Wallpapers Wall Vinyls and Plastics Wallcoverings《卷式壁衬 成品壁纸 聚乙烯壁纸和塑料壁纸的规范》.pdf

1、STD-BSI BS EN 233-ENGL 1199 m lb24bb9 OULb70 T2T BslJ BRITISH STANDARD Wallcoverings in roll form - Specification for finished wallpapers, wall vinyls and plastics wallcoverings The European Standard EN 233:1999 has the status of a British Standard ICs 91.180 NO COPYING WITHOUT BSI PERMISSION EXCEPT

2、 AS PERMITTED BY COPYRIGHT LAW BS EN 233:1999 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- STDOBSI BS EN 233-ENGL 1999 Lb24bb 0801b71 bb I direction of the Consumer Products

3、and Services Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 October 1999 Arnd. No. O BSI 10-1999 BS EN 233:1999 Date Comments National foreword This British Standard is the English language version of EN 233 1999. It supersedes BS EN 233 19

4、97 which is withdram. The UK participation in its prepasation was enbusted to Technical Committee CW/35, Wallcoverings, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible European committee any enquiries on the - monitor related international and Eu

5、ropean developments and promulgate interpretation, or proposals for change, and keep the UK interests informed them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standasds which implement international or Eu

6、ropean publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the nec

7、essary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN titie page, p

8、ages 2 to 6, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. ISBN O 580 32654 3 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking p

9、ermitted without license from IHS-,-,-STD=BSI BS EN 233-ENGL 3999 W Lb24bb9 0801b72 AT2 I EUROPW S“DARD NORME EUROPENNE EXJROPma NORM EN 233 June 1999 ICs 91.180 Supersedes EN 2331989 English version Wdcovekgs in roll form - Speeifidon for finished wallpapen, wall vinyls and piastics wallcoverings R

10、evtements muraux en rouleaux - Spcification des papiers peints nis, des revtements muraux vinyles et des revtements muraux en plastique Wandbekleidungen in Rollen - Festlegungen fur fertige Papier-, Viyl- und KunstsofwandbeMeidungen This European Standard was approved by CEN on 24 April 1999. CEN me

11、mbers are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the stat of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applicatio

12、n to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the sa

13、me status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norwax Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee f

14、or Standardization Comit Europen de Normalisation Europisches Komitee fur Normung Central Secretariat: rue de Stassart 36, B-1060 Brussels O 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 233:199!3 E Copyright European Commit

15、tee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD-BSI BS EN 233-ENGL 1999 Lb29bbS 080Lb73 739 Page 2 EN 233:1999 Foreword This European Standard has been prepared by Technical Committee CEN/TC 99 Wallc

16、overings, the Secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 1999, and conflicting national standards shall be withdrawn at the latest by November 19

17、99. According to the CENKENELEC Internai Regulations, the national standards organizations of the following countries are bound to implement #i European Standard: Austria, Belgium, Czech Republic, Denmark, Fnland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Por

18、tugal, Spain, Sweden, Switzerland and the United Kingdom. This European Standard replaces EN 2331989 and EN 233: 1989/A1: 1996. It specifies the requirements for finished wallpapers, wall vinyls and plastics wallcoverings. The relevant test methods: dimensions, straightness, spongeabiity and washabi

19、lity are described in EN 12956. EN 233 includes an annex A, Sampling (normative) and an informative annex B, Adeviation which are integrai parts of the sandard. Contents Foreword Introduction 1 Scope 2 Normative references 3 Definitions 4 Categories 5 Specifications 6 Matching, application of adhesi

20、ve, 7 Marking, labelling, packaging 8 Classification and designation Annex A (normative) Sampling for testing Annex B (informative) Adeviations Bibliography removal and miscellaneous symbols Page 2 3 3 3 3 3 3 O BSI 10-1999 Copyright European Committee for Standardization Provided by IHS under licen

21、se with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD.6S.I BS EN 233-ENGL 1997 Is 162Llbb7 nAfllb7Y 675 II Introduction A finished wallcovering is one that is not intended to be decorated after hanging. There are many types of wallcovering and varied proce

22、sses used in their manufacture. To ensure satisfactory performance, it is important that the decorators follow the manufacturers recommended hanging instructions for each particular product. Various grades of washability and colour fastness to light of frnished wallcoverings are permitted. These gra

23、des will facilitate the selection by the user of an appropriate wallcovering and guide the decorator. other European Standards on the vocabulary used in the wailcovering indusm, wallcoverings for subsequent decoration, textile wallcoverhgs and heavy duty wailcoverings are also published EN 235, Wall

24、coverings in roU .form - Voca.bula,ry and symbols. EN 234, Wallcoverings in roll form - Specifkatim for wall;.overings for subsequent decoration. EN 259, Wa coverings in roU form - SpecZfication far kavy duty wall coverings. EN 266, Wa covmhgs in roU .form - Specication for textile wall covmhgs. EN

25、12 149, WauCovm:ngs in roU form - Detemzinatihz of migration of heavy metals and certain other elements, of vinyl chloride monorner and of formakhyde release. EN 12956, Wallcoverings in roll forrn- Detemzinatwn of dimensions, straightness, spongeability and washability. 1 Scope This European Standar

26、d - specifies requirements for fihed wallpapers, wall vinyls and plastics wallcoverings; - specifies requirements for marking; - gives the designation system. The marking requirements of this standard are primarily for the consumers infodon to enable optimum selection of the product. This standard a

27、pplies to finished wallpapers, wall vinyls and plastics wallcoverings not intended for subsequent decoration supplied in roils for hanging on walls and ceilings by means of an adhesive covering the whole of the interface between the wallcovering and the support (wall or ceiling). Excluded from this

28、standard are rigid materials, materials not attached or not wholly attached by adhesive, wallcoverings for subsequent decoration, textile wallcoverings and non-decomtive wallcoverings such as wall ligs or those with special properties, e.g. thermal or acoustic insulation. Page 3 EN 233A999 2 Normati

29、ve references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of an

30、y of these publications apply to this standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 235, Wailcoverings in roll fom - Vocabulan/ and spbols. EN 12149, Wa,llcoverings in roU form - Determinutian of m

31、igra,ti,on of heavy meas and certain other elements, of vinyl chloride monomer and of formaki?ehyde release. EN 12956, Wadcoverings in roU form - Determination of dimensions, straightness, spongeability and washabili 1 y. EN 20105B02, Textiles - Tests for colour fastness - Part B02: Colour fastness

32、to artifkid light (Xenon arc fading lamp test). (IS0 105B02:1988) EN IS0 186, Paper ar Category 2 designates the wallcoverings covered by this standard and characterized by a minimum nominal width threshold and Category 3 designates friezes. 5 Specifications 5.1 General The dimensions specified for

33、the three categories of covering shall be measured in accordance with the requirements of EN 12956. See annex A. O BSI 10-1999 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD

34、BSI BS EN 233-ENGL 1777 W lb24hb7 0801b75 501 I Heavy metal Symbol or element Page 4 EN ml999 Maximum migration in mgkg of wallcovering 5.2 Dimensions 5.2.1 Categoty 1 The area of the roll shall be 5 326 m2 The nominal width and length of a roll shall be marked. The actual width and length shall no

35、t deviate from the nominal values by more than 1,5 %. The nominal width shall be not less than 50 cm and not greater than 53 cm. 5.2.2 Categoru 2 The nominal width and length of a roll shall be marked The tolerance on the actual width and length shall be - parallelity the 3 width measurements taken

36、in accordance with the requirements of EN 12956 shall not differ by more than 1 mm. 3 % 5.4 Spongeability For a wallcovering conforming to this standard, it shall be possible to wipe off the hanging adhesive while it is still damp from the front face of the wallcovering with a damp cloth or sponge w

37、ithout causing visible damage- Accordingly, a wallcovering subjected to the spongeability test described in EN 12956 shall exhibit no damage or change likely to alter its appearance as a wallcovering. This symbol indicating this “spongeable“ level shall be as given in EN 235. 6.5 Washability 5.5.1 i

38、f a wallcovering is claimed to be washable during its life after hanging, it shall be qualified as “washable“, “extra-washable or “scrubbable“ according to its grade of washabiliw. 5.5.2 When tested under the test conditions specified for each level of washability by EN 12956, a wailcovering shall e

39、xhibit no damage or change likely to alter its appearance as a wallcovering compared with the reference sample. 5.5.3 The symbols indicatjng the washability levels shall be as given in EN 235. Cadmium Chromium Cd 25 Cr 60 1 Arsenic* IAS 18 I 1 Barium I Ba I 1 O00 I 1 Lead I Pb I 90 I I Selenium I Se

40、 I 165 I * The limit for Sb is not applicable to wallcoverings that have fire reaction properties that appear in an evaluation test report. * The limit for As is not applicable to wallcoverings that claini to have undergone anti-fungal or anti-bacterial treatment. O BSI 10-1999 Copyright European Co

41、mmittee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD-BSI BS EN 233-ENGL 1999 sl Lb24bb 08Lb76 448 Table 2 - Analytical correction factor correction factor 5.8 Maximum vinyl chloride monomer (VCM) cont

42、ent 5.8.1 Test method The test method shall be method B of EN 12149. 5.8.2 Requirements The maximum vinyl chloride monomer (VCM) content, measured as mg/kg of wallcovering, shall not exceed 0,2. 5.9 Maximum formaldehyde release 5.9.1 Test method The test method shall be method C of EN 12149. 5.9.2 R

43、equirements The maximum formaldehyde release, measured as mgkg of wallcovering, shall not exceed 120. 6 Matching, application of adhesive, removal and miscellaneous symbols 6.1 The symbols indicating patteni matching shall be as given in EN 235. 6.2 The symbols indicating means of application of the

44、 adhesive shall be as given in EN 235. 6.3 The symbols indicating the method of removal shall be as given in EN 235. 6.4 A symbol indicating overlapping joins and double cutting and a symbol indicating a duplex embossed wallcovering shail be as given in EN 235. 7 Marking, labelling, packaging 7.1 Vi

45、sible marking When compliance with this standard is claimed, the rol, its packaging or a label inside the packaging of the roll shall state the specific chasacteristics of the wallcovering in such a way that the information below cam be read by the purchaser without removing the roll designates wash

46、ability box: insert the letter from EN 235 corresponding to the grade of washability; designates colour fastness to light box: insert the corresponding figure; designates application of adhesive box: inserL the corresponding letter from EN 235; designates removal box: insert the corresponding figure

47、 from EN 235. EXAMPLE A finished wallcovering, of width 0,53 m and length 10,05 m, “scrubbable”, with “good colour fastness to ight, prepasted and peelable is designated as follows: Wallcovering EN 233 - 053 X 1005 D 5 K 2 O BSI 10-1999 Copyright European Committee for Standardization Provided by IH

48、S under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD=BSI BS EN 233-ENGL 1997 W 1b2Ybb7 IIBIILb77 3Bq E Page 6 EN 2331999 Annex A (normative) Sampling for testing A-deviations Samples for testing shall be taken from wallcoverings not more than

49、 14 days after manufacture, in accordance with EN IS0 186, except that: Annex B (informative) A-deviation: National deviation due to regulations, the alteration of which is for the time being outside the competence of the CENXENELEC member. a) for the purposes of this standard, a making is regarded as equivalent to a lot, and a ro is a unit. Each lot makin