EN 2349-306-2006 en Aerospace series - Requirements and test procedures for relays and contactors - Part 306 Overload d c and a c 《航空航天系列 继电器和电流接触器要求和试验程序 第306部分 交直流负荷》.pdf

1、BRITISH STANDARDBS EN 2349-306:2006Aerospace series Requirements and test procedures for relays and contactors Part 306: Overload d.c. and a.c.The European Standard EN 2349-306:2006 has the status of a British StandardICS 49.060g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g

2、53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 2349-306:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2007 BSI 2007ISBN 978 0 580 50022 0N

3、ational forewordThis British Standard was published by BSI. It is the UK implementation of EN 2349-306:2006.The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Panel ACE/6/-/4, Aerospace Switching devices.A l

4、ist of organizations represented on ACE/6/-/4 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal ob

5、ligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 2349-306October 2006ICS 49.060English VersionAerospace series - Requirements and test procedures for relaysand contactors - Part 306: Overload d.c. and a.c.Srie arospatiale - Exigence

6、s et mthodes dessais desrelais et contacteurs - Partie 306 : Surcharges courantcontinu et alternatifLuft- und Raumfahrt - Anforderungen und Prfverfahren frRelais und Schaltschtze - Teil 306: berlast bei Gleich-und WechselstromThis European Standard was approved by CEN on 10 May 2006.CEN members are

7、bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the

8、Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status a

9、s the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Sloven

10、ia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN nation

11、al Members.Ref. No. EN 2349-306:2006: E2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Mounting method.4 4 Test procedures.4 5 Test criteria.5 6 Verification test5 EN 2349-306:20063 Foreword This document (EN 2349-306:2006) has been prepared by the AeroSpace and Defense Industries Ass

12、ociation of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. Th

13、is European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2007, and conflicting national standards shall be withdrawn at the latest by April 2007. Attention is drawn to the possibility that some of the

14、elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement thi

15、s European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kin

16、gdom. EN 2349-306:20064 1 Scope This standard specifies a method for testing the overload d.c. and a.c. of relays and contactors. It shall be used together with EN 2349-100. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated re

17、ferences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2349-100, Aerospace series Requirements and test procedures for relays and contactors Part 100: General requirements 1)EN 2349-303, Aerospace series

18、Requirements and test procedures for relays and contactors Part 303: Dielectric strength 3 Mounting method The switching device shall be wired in accordance with EN 2349-100. The rated overload current and the open circuit voltage shall be applied in accordance with product standard. The test sample

19、 shall be mounted in still air. 4 Test procedures 4.1 Each operating and resting contact shall be able to connect, conduct and disconnect the overload in accordance with the product standard. The operating and normally closed contacts shall be tested separately. 4.2 The coil of the switching device

20、shall be energized with the rated voltage during the test. The contacts shall be monitored during connection, conduction and disconnection. A functional defect of the test sample shall constitute a failure. A voltage drop across closed contacts over 10 % of the supply voltage shall constitute a fail

21、ure. During the test, the housing of the relay or contactor shall be connected to the d.c. earth or neutral wire of the electrical installation by a fuse with a rating of 5 % of the rated resistive contact current, but not greater than 3 A. 4.3 Blowing of the fuse shall constitute a failure. 4.4 Tes

22、t cycle: connection time: (0,2 0,05) s for a.c.; (0,5 0,05) s for d.c. disconnection time: (20 1) s. Number of switching cycles: see product standard.1) In preparation at the date of publication of this standard. EN 2349-306:20065 4.5 The temperature increase shall be measured for: plug-in relays: o

23、n the housing; screw-type connections: on the connector bolt. 5 Test criteria There shall be: no electrical or mechanical failure; no sticking or seizing of contacts; no blowing of the fuse; no temperature increase greater than 75 C. 6 Verification test Test in accordance with EN 2349-303. EN 2349-3

24、06:2006BS EN 2349-306:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.Revisio

25、nsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambigui

26、ty while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that su

27、bscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the

28、 BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europea

29、n and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email

30、: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membership

31、bsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publi

32、cations of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written perm

33、ission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.