EN 2349-310-2006 en Aerospace series - Requirements and test procedures for relays and contactors - Part 310 Rupture《航空航天系列 继电器和电流接触器要求和试验程序 第310部分 断裂》.pdf

1、BRITISH STANDARDBS EN 2349-310:2006Aerospace series Requirements and test procedures for relays and contactors Part 310: RuptureThe European Standard EN 2349-310:2006 has the status of a British StandardICS 49.060g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g

2、44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 2349-310:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2007 BSI 2007ISBN 978 0 580 50026 8National forewor

3、dThis British Standard was published by BSI. It is the UK implementation of EN 2349-310:2006.The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Panel ACE/6/-/4, Aerospace Switching devices.A list of organiza

4、tions represented on ACE/6/-/4 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amend

5、ments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 2349-310October 2006ICS 49.060English VersionAerospace series - Requirements and test procedures for relaysand contactors - Part 310: RuptureSrie arospatiale - Exigences et mthodes dessais desrelais

6、 et contacteurs - Partie 310 : RuptureLuft- und Raumfahrt - Anforderungen und Prfvefahren frRelais und Schaltschtze - Teil 310: SchaltvermgenThis European Standard was approved by CEN on 19 May 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditi

7、ons for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three offic

8、ial versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belg

9、ium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZAT

10、IONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2349-310:2006: E2 Contents Page Foreword3 1 Scope 4 2 Normativ

11、e references 4 3 Mounting method.4 4 Test procedures.4 5 Test criteria.5 EN 2349-310:20063 Foreword This document (EN 2349-310:2006) has been prepared by the AeroSpace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with

12、the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identic

13、al text or by endorsement, at the latest by April 2007, and conflicting national standards shall be withdrawn at the latest by April 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard:

14、 Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 2349-310:20

15、064 1 Scope This standard specifies a method for testing the rupture characteristics of relays and contactors. It shall be used together with EN 2349-100. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the

16、edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2349-100, Aerospace series Requirements and test procedures for relays and contactors Part 100: General requirements 1)3 Mounting method The relay or contactor shall be

17、 wired in accordance with EN 2349-100 and the rated contact load. The test sample shall be mounted in still air. 4 Test procedures 4.1 Each operating and resting contact shall be able to connect, conduct and disconnect the loads specified in the product standards. 4.2 During the test, the housing of

18、 the relay or contactor shall be connected to the d.c. earth or the neutral lead of the electrical installation by a fuse with a rating of 5 % of the rated resistive contact current, but not greater than 3 A. 4.3 One sample shall be tested for each load. Operating and normally closed contacts shall

19、be tested separately. For tests with multi-phase a.c. current, the load shall be applied to adjacent contacts. 4.4 The coil of the relay or contactor shall be energized at the rated voltage during the test. 4.5 The contacts shall be monitored during connection, conduction and disconnection. 4.6 A fu

20、nctional defect shall constitute a failure. A voltage drop over 10 % of the open contact voltage shall constitute a failure. Blowing of the fuse shall constitute a failure. 4.7 Test cycle: connection time: (0,2 0,05) s; disconnection time: (30 1) s. Number of test cycles: see product standard. 1) In

21、 preparation at the date of publication of this standard. EN 2349-310:20065 4.8 The temperature increase shall be measured for: plug-in relays, on the case; screw-type connections: on the connector bolt. 5 Test criteria No electrical or mechanical failure; no sticking or seizing of contacts; no blow

22、n fuse; no temperature increase above 75 C. EN 2349-310:2006BS EN 2349-310:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the internation

23、al level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would b

24、e grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individu

25、al updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Ema

26、il: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI prov

27、ides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:

28、 +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8

29、996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications.

30、BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopyi

31、ng, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.