1、BRITISH STANDARDBS EN 2349-414:2007Aerospace series Requirements and test procedures for relays and contactors Part 414: Mechanical shockICS 49.060g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g
2、3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 2349-414:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 August 2008 BSI 2008ISBN 978 0 580 56759 9National forewordThis British Standard is the UK implementation of EN 2349-414:2007
3、. The UK participation in its preparation was entrusted to Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessa
4、ry provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 2349-414April 2007ICS 49.060Eng
5、lish VersionAerospace series - Requirements and test procedures for relaysand contactors - Part 414: Mechanical shockSrie arospatiale - Exigences et mthodes dessais desrelais et contacteurs - Partie 414 : Chocs mechaniqueLuft- und Raumfahrt - Anforderungen und Prfverfahren frRelais und Schaltschtze
6、- Teil 414: MechanischesSchockenThis European Standard was approved by CEN on 19 May 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lis
7、ts and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the respon
8、sibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Icelan
9、d, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassa
10、rt, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2349-414:2007: E2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Method 4 4 Requirements.5 BS EN 2349-414:20073 Foreword This document (EN 2349
11、-414:2007) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services o
12、f the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2007, and conflicting national standards shall be withdrawn at the latest
13、 by October 2007. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national stan
14、dards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, P
15、ortugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 2349-414:20074 1 Scope This standard specifies a method for checking the capability of relays and contactors to withstand shock. It shall be used together with EN 2349-100. 2 Normative references The follo
16、wing referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2349-100, Aerospace series Requirements and test proced
17、ures for relays and contactors Part 100: General requirements 1)EN 2349-301, Aerospace series Requirements and test procedures for relays and contactors Part 301: Pick-up and drop-out voltage EN 2349-303, Aerospace series Requirements and test procedures for relays and contactors Part 303: Dielectri
18、c strength EN 2349-304, Aerospace series Requirements and test procedures for relays and contactors Part 304: Operate and release time EN 2349-305, Aerospace series Requirements and test procedures for relays and contactors Part 305: Bounce time EN 2349-307, Aerospace series Requirements and test pr
19、ocedures for relays and contactors Part 307: Contact voltage drop EN 2349-309, Aerospace series Requirements and test procedures for relays and contactors Part 309: Exported spikes EN 2349-412, Aerospace series Requirements and test procedures for relays and contactors Part 412: Seal ISO 7137:1995,
20、Aircraft Environmental conditions and test procedures for airborne equipment 2)3 Method 3.1 Mounting Mounting of the relay or contactor on the drop slide shall be rigid, so that the shock produced can be transmitted directly to the test sample without absorption or resonance. The electrical connecti
21、ons shall be wired in accordance with the product standard. The wires shall be secured to the drop slide as close as possible to the point of electrical connection. 1) In preparation at the date of publication of this standard. 2) Endorsement of publications EUROCAE/ED-14 and RTCA/DO-160. BS EN 2349
22、-414:20075 3.2 Procedure The relay or contactor shall be subjected to a shock test in accordance with ISO 7137. For test conditions see product standard. 4 Requirements The torque for the connections and attachments shall not be less than 80 % of the rated value. No opening of closed contacts for lo
23、nger than 10 s. No closing of open contacts for longer than 1 s. Test in accordance with EN 2349-301, EN 2349-303, EN 2349-304, EN 2349-305, EN 2349-307, EN 2349-309, and EN 2349-412. BS EN 2349-414:2007BS EN 2349-414:2007BSI Group Headquarters389 Chiswick High Road,London W4 4AL, UKTel +44 (0)20 89
24、96 9001Fax +44 (0)20 8996 Standards Institution (BSI)BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendme
25、nt or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would
26、 inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest e
27、ditions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ res
28、ponse to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through
29、 its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept u
30、p to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via
31、 British Standards Online can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under th
32、e Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementi
33、ng the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070 Email:
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1