EN 2349-415-2007 en Aerospace series - Requirements and test procedures for relays and contactors - Part 415 Acceleration《航空航天系列 继电器和连接器的要求及测试程序 第415部分 加速度》.pdf

1、BRITISH STANDARDBS EN 2349-415:2007Aerospace series Requirements and test procedures for relays and contactors Part 415: AccelerationICS 49.060g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37

2、g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 2349-415:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 August 2008 BSI 2008ISBN 978 0 580 56760 5National forewordThis British Standard is the UK implementation of EN 2349-415:2007. Th

3、e UK participation in its preparation was entrusted to Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary p

4、rovisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 2349-415April 2007ICS 49.060English

5、 VersionAerospace series - Requirements and test procedures for relaysand contactors - Part 415: AccelerationSrie arospatiale - Exigences et mthodes dessais desrelais et contacteurs - Partie 415 : AcclrationLuft- und Raumfahrt - Anforderungen und Prfverfahren frRelais und Schaltschtze - Teil 415: Be

6、schleunigungThis European Standard was approved by CEN on 19 May 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographic

7、al references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN me

8、mber into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, L

9、atvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brusse

10、ls 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2349-415:2007: E2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Method 4 4 Requirements.5 BS EN 2349-415:20073 Foreword This document (EN 2349-415:2007) has been

11、prepared by the AeroSpace and Defense Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member co

12、untries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2007, and conflicting national standards shall be withdrawn at the latest by October 2007.

13、 According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

14、 Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 2349-415:20074 1 Scope This standard specifies a method for checking the capability of relays and contactors to withstand acceleration.

15、It shall be used together with EN 2349-100. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any ame

16、ndments) applies. EN 2349-100, Aerospace series Requirements and test procedures for relays and contactors Part 100: General requirements 1)EN 2349-301, Aerospace series Requirements and test procedures for relays and contactors Part 301: Pick-up and drop-out voltage EN 2349-303, Aerospace series Re

17、quirements and test procedures for relays and contactors Part 303: Dielectric strength EN 2349-304, Aerospace series Requirements and test procedures for relays and contactors Part 304: Operate and release time EN 2349-305, Aerospace series Requirements and test procedures for relays and contactors

18、Part 305: Bounce time EN 2349-307, Aerospace series Requirements and test procedures for relays and contactors Part 307: Contact voltage drop EN 2349-309, Aerospace series Requirements and test procedures for relays and contactors Part 309: Exported spikes ISO 2669, Environmental tests for aircraft

19、equipment Steady-state acceleration 3 Method 3.1 Mounting Mounting of the relay or contactor on the holder shall be rigid, so that the acceleration produced can be transmitted directly to the test sample without absorption or resonance. The electrical connections shall be wired in accordance with th

20、e product standard. The wires shall be secured to the accelerator as close as possible to the point of electrical connection. 3.2 Procedure The relay or contactor shall be subjected to an acceleration test according to 3.2 ”Steady state acceleration” of ISO 2669. For test conditions see product stan

21、dard. 1) In preparation at the date of publication of this standard. BS EN 2349-415:20075 4 Requirements No opening of closed contacts for longer than 10 s. No closing of open contacts for longer than 1 s. Test in accordance with EN 2349-301, EN 2349-303, EN 2349-304, EN 2349-305, EN 2349-307 and EN

22、 2349-309. BS EN 2349-415:2007BS EN 2349-415:2007BSI Group Headquarters389 Chiswick High Road,London W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards Institution (BSI)BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards

23、in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our p

24、roducts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400

25、BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001

26、Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise reque

27、sted.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services.

28、 Contact the Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Admini

29、stration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI als

30、o holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, rec

31、ording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070 Email: