EN 2589-2017 en Aerospace series - Steel - Sheet and strip cold rolled - Thickness 0 1 mm less than or equal to a less than or equal to 3 mm - Dimensions《航空航天系列-钢片和带冷轧厚度0 1mm小于或等于a.pdf

1、BS EN 2589:2017 Aerospace series Steel Sheet and strip, cold rolled Thickness 0,1 mm a 3 mm Dimensions BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 2589:2017 BRITISH STANDARD National foreword This British Standard is the UK implementation of EN 2589:2017.

2、The UK participation in its preparation was entrusted to Technical Committee ACE/61, Metallic materials for aerospace purposes. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions

3、 of a contract. Users are responsible for its correct application. The British Standards Institution 2017. Published by BSI Standards Limited 2017 ISBN 978 0 580 95329 3 ICS 49.025.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was publishe

4、d under the authority of the Standards Policy and Strategy Committee on 28 February 2017. Amendments/corrigenda issued since publication Date T e x t a f f e c t e dBS EN 2589:2017 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2589 February 2017 ICS 49.025.10 English Version Aerospace series

5、- Steel - Sheet and strip, cold rolled - Thickness 0,1 mm a 3 mm - Dimensions Srie arospatiale - Acier - Tles et bandes lamines froid - paisseurs 0,1 mm a 3 mm - Dimensions Luft- und Raumfahrt - Stahl - Bleche und Bnder, kaltgewalzt - Dicken 0,1 mm a 3 mm - Mae This European Standard was approved by

6、 CEN on 14 November 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stan

7、dards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and n

8、otified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary,

9、 Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-

10、CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2589:2017 EBS EN 2589:2017 EN 2589:2017 (E) 2 Contents Page European foreword . 3 1 Scope. 4 2 Normative references.

11、4 3 Required characteristics. 4 3.1 Form 4 3.2 Dimensions 5 3.2.1 Thickness and mass 5 3.2.2 Width 6 3.2.3 Length. 6 3.3 Dimensional tolerances. 6 3.3.1 Thickness 6 3.3.2 Width 7 3.3.3 Length (only for sheet) 8 3.4 Geometric tolerances (only for sheet) . 8 3.4.1 Squareness. 8 3.4.2 Lateral curvature

12、 9 3.4.3 Flatness 9 3.5 Materials . 9 4 Designation 9 BS EN 2589:2017 EN 2589:2017 (E) 3 European foreword This document (EN 2589:2017) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance wi

13、th the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an iden

14、tical text or by endorsement, at the latest by August 2017, and conflicting national standards shall be withdrawn at the latest by August 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held r

15、esponsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, F

16、inland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 2589:2017 EN 25

17、89:2017 (E) 4 1 Scope This European Standard specifies the dimensions and tolerances of sheets and strips, cold rolled, in steel, thickness 0,1 mm a 3 mm, for aerospace applications. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and

18、are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2600, Aerospace series Designation of metallic semi-finished products Rules 1)EN 3848, Aerospace s

19、eries Semi-finished metallic products Methods of measuring form deviations TR 2410, Metallic materials Relationship between dimensional standards and metallic material standards 2)3 Required characteristics 3.1 Form See Figure 1. Figure 1 1) Published as ASD-STAN Prestandard at the date of publicati

20、on of this European Standard. 2) Published as ASD-STAN Technical Report at the date of publication of this European Standard. BS EN 2589:2017 EN 2589:2017 (E) 5 3.2 Dimensions 3.2.1 Thickness and mass 3.2.1.1 Sheet See Table 1. Table 1 a Mass per unit area aNominal mm kg/m 20,5 3,9 0,6 4,7 0,8 6,3 1

21、,0 7,9 1,2 9,4 1,4 11,0 1,6 12,6 1,8 14,1 2,0 15,7 2,5 19,6 3,0 23,6 aFor information, calculated with a density: 7,85 kg/dm 3 . 3.2.1.2 Strip See Table 2. Table 2 a Mass per unit area aNominal mm kg/m 20,1 0,8 0,2 1,6 0,3 2,4 0,4 3,1 0,5 3,9 0,6 4,7 0,8 6,3 1,0 7,9 1,2 9,4 1,4 11,0 1,6 12,6 1,8 14,

22、1 2,0 15,7 2,5 19,6 aFor information, calculated with a density: 7,85 kg/dm 3 . BS EN 2589:2017 EN 2589:2017 (E) 6 3.2.2 Width Width is not specified. 3.2.3 Length Length is not specified. 3.3 Dimensional tolerances 3.3.1 Thickness Measurements shall be taken at least 20 mm from the edge. For strip

23、b 40 mm, the thickness is measured on the reference line. 3.3.1.1 Sheet See Table 3. Table 3 Dimensions in millimetres Thickness Tolerances () for a width: b 1 200 1 200 b 1 500 1 500 b 2 000 a 0,6 0,05 0,6 a 0,8 0,06 0,8 a 1,0 0,07 1,0 a 1,2 0,08 0,09 1,2 a 1,6 0,08 0,09 0,13 1,6 a 2,0 0,09 0,10 0,

24、14 2,0 a 2,5 0,10 0,11 0,15 2,5 a 3,0 0,11 0,12 0,16 BS EN 2589:2017 EN 2589:2017 (E) 7 3.3.1.2 Strip See Table 4 Table 4 Dimensions in millimetres Thickness Tolerances () for a width: b 125 125 b 250 250 b 600 a 0,1 0,01 0,1 a 0,3 0,02 0,3 a 0,4 0,03 0,03 0,03 0,4 a 0,5 0,03 0,03 0,04 0,5 a 0,6 0,0

25、3 0,04 0,04 0,6 a 0,8 0,04 0,05 0,05 0,8 a 1,0 0,04 0,05 0,05 1,0 a 1,4 0,06 0,07 1,4 a 2,0 0,07 0,08 2,0 a 2,5 0,08 0,09 3.3.2 Width 3.3.2.1 Sheet See Table 5. Table 5 Dimensions in millimetres Width Tolerances b 2 000 +2 0BS EN 2589:2017 EN 2589:2017 (E) 8 3.3.2.2 Strip See Table 6. Table 6 Dimens

26、ions in millimetres Width Tolerances for a thickness a 0,3 0,3 2 500 0,4 % l BS EN 2589:2017 EN 2589:2017 (E) 9 3.4.2 Lateral curvature 3.4.2.1 Method of measurement See EN 3848. 3.4.2.2 Tolerances See Table 9. Table 9 Dimensions in millimetres Thickness Lateral curvature F on length width 0,5 a 3 0

27、,2 % l 0,2 % b 3.4.3 Flatness 3.4.3.1 Method of measurement See EN 3848. 3.4.3.2 Tolerances See Table 10. Table 10 Dimensions in millimetres Thickness for a chord of: W a 1 200 1 200 1,4 8 10 15 0,8 % W aW = l or b If necessary, other values can be defined after agreement between the manufacturer an

28、d the purchaser. 3.5 Materials See TR 2410. 4 Designation See EN 2600. This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Roy

29、al Charter. British Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) About us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -ba

30、sed solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide y

31、ou with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted Eur

32、opean and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Copyright in BSI publications All the conten

33、t in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.

34、Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent. Storing

35、 and using standards Standards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and t

36、hat only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any f

37、ormat to create an additional copy. This includes scanning of the document. If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions). Reproducing extracts For permission to rep

38、roduce content from BSI publications contact the BSI Copyright & Licensing team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have instant a

39、ccess to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in si

40、ngle copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member a

41、nd the benefits of membership, please visit With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current

42、. For further information, email . Revisions Our British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publ

43、ication please inform the Knowledge Centre. Useful Contacts Customer Services Tel: +44 345 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 345 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK BSI Back Cover.indd 1 27/01/2016 14:20