EN 2591-409-1999 en Elements of Electrical and Optical Connection - Test Methods - Part 409 Contact Retention in Insert《航空航天系列 光电连接元件的试验方法 第409部分 插入式接触固定》.pdf

1、BRITISH STANDARD AEROSPACE SERIES Elements of electrical and optical connection - Test methods - Part 409: Contact retention in insert The European Standard EN 2591-409:1999 has the status of a British standard ICs 49.060 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGH LAW BS EN 25

2、91-4091999 _- STD=BSI BS EN 2511-405-ENGL 1779 E lh24bb7 078Lb57 705 = been prepared under the direction of the Engineering Amd. No. Date Sector Committee, was published under the authority of the Standards Commi - present to the responsible inmnationaUEhropean committee any enquiries on the intepre

3、tation, or proposals for change, and keep the UK interests informed; - monitor related international and European developments and promulgate them in the UK. A list of organizatons represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards wh

4、ich implement internalional or European publications refed to in this document may be found in the BSI Standards Catalogue under the section entitled “Intemational Standards Correspondence Index”, or by using the Find” faciiity of the BSI Standards Electronic Catalogue. A British standard does not p

5、urport to include all the necessary provisions of a conira - load to be applied and its applcation point; - allowable displacements 1) under load. 2) after removal of load, . - final measurements and requirements (if applicable). Page 4 EN 2591 -49:1999 1 to5 6 to 60 61 to 130 2 131 4 Method 1 O0 50

6、 (with a minimum of 6 specimens) 25 (with a minimum of 31 specimens) 10 (with a minimum of 34 specimens) 4.1 See table 1. Number of contacts to be tested for each size Table 1 Number to be tested 740 Number of contacts At least one contact shall be close to the insert periphery and one near the cent

7、re. 4.2 Procedure Each contact shall be submitted to the specified axial preload. The load shall be increased at a rate not exceeding 5 N/s until the specified value is reached and maintained for 10 s. The maximum contact displacement shall be measured: - while the load is applied; - after the load

8、is removed. This test shall then be repeated in the opposite direction. 4.3 The measured values shall be within the specified limits. The specimens shall be submitted to a visual examination (EN 2591-101). No damage which would impair their operation shall be observed. Final measurements and require

9、ments (if applicable) BS EN 25911409:1999 BSI 389 Ck-wick High bad London w4 4AL BSI - British Standards Institution BSI is the independent nationai body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international leveL It is incorporated by R

10、oyal Charter. Revisions British standards are updated by amendment or revision. Usem of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone nding an i

11、naccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tek 020 8996 9OOO. Fax: O20 8996 7400. BSI offers members an individual updating service called PLUS which ensure

12、that subscriben automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards pubiidons should be addressed to Customer Services. Tek 020 8996 9001. Fax O20 8996 7001. In response to ordem for international standards, it is BSI polic

13、y to supply the BSI implementation of those that have been published as British Standards, unless otherwiserequ Information on standards BSI provides a wide range of information on national, European and interrdionai standards through its Libmy and its khnical Help to Exporters Service. Various BSI

14、electronic information services are also available which give details on a its products and services. Contact the Infom-tation Centre. Tek 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards deveiopmens and receive substantial discounts on the purchase pr

15、ice of standards. For details of these and other benefits contact Membership Adminismition. Tel: O20 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in ali BSI publications. J3SI also holds the copmt, in the K, of the publications of the internaiional standardhation bodies. Except as per

16、mitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a reievai system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written pennission from BSI. This does not preclude the he use, in the cours

17、e of implementing the standard, of necessary details such as symbols, and size, type or grade des&jnations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained if permission is granted, the terms may include royalty payments or a licensing agreement. Dem and advice can be obtained hm the Copyright Manager. bk 020 8996 7070.