EN 2829-1994 en Aerospace Series - Adhesion Test for Metallic Coatings by Shot Peening《航空航天系列 用喷丸加工法作金属涂层的粘附性试验》.pdf

1、CEN EN*2829 94 3404589 0089373 5T3 e BRITISH STANDARD AEROSPACE SERIES Adhesion test for metallic coatings by shot peening The European Standard EN 2829 : 1994 has the status of a British Standard BS EN 2829 : 1995 CEN ENx2829 94 = 3404589 0089374 43T = BS EN 2829 : 1995 Amd. No. Date This British S

2、tandard, having been prepared under the direction of the Engineering Sector Board (E/-), was published under the authority of the Standards Board and comes into effect on 15 March 1995 O BSI 1995 lxt affected The following BSI references relate to the work on this standard: Committee reference ACE44

3、 Draft for comment 9075752 DC ISBN O 580 23703 6 Cooperating organizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: Austria Belgium Denmark Finland France

4、Germany Greece Iceland Ireland Italy Luxembourg Netherlands Norway Portugal Spain Sweden Switzerland United Kingdom Oesterreichisches Nonnungsinstitut Institut belge de normalisation Dansk Standard Suomen Standardisoimisliito, r. y. Association franaise de normalisation Deutsches Institut fr Normung

5、 e.V. Hellenic Organization for Standardization Technological Institute of Iceland National Standards Authority of Ireland Ente Nazionale Italiano di Unificazione Inspection du Travail et des Mines Nederlands Normalisatie-instituut Norges Standardiseringsforbund Instituto Portugus da Qualidade Asoci

6、acin Espaola de Normalizacin y Certificacin Standardiseringskommissionen i Sverige Association suisse de normalisation British Standards Institution CEN EN*2827 94 = 3404589 0089375 37b BS EN 2829 : 1995 Contents pape Cooperating organizations Inside front cover National foreword i Foreword 2 Text o

7、f EN 2829 3 National annex NA (informative) Committees responsible Inside back cover National annex NB (informative) Cross-references Inside back cover National foreword This British Standard has been prepared under the direction of the Engineering Sector Board and is the English language version of

8、 EN 2829 : 1994 Amspace series - Adhesion test for metallic coatings by shot peening, published by the European Committee for Standardization (CEN). EN 2829 was produced as a result of international discussion in which the United Kingdom took an active part. Compliance with a British Standard does n

9、ot of itself confer immunity from legal obligations. i CEN ENx2829 94 3404589 0087176 202 EUROPEAN STANDARD EN 2829 NORME EUROPENNE EUROPISCHE NORM December 1994 ICs 49.040.40 Descriptors: Aircraft industry, metal coatings, coating processes, adhesion tests English version Aerospace series - Adhesio

10、n test for metallic coatings by shot peening Srie arospatiale - Essai dadhrence des revtements mtalliques par martelage Luft- und Raumfahrt - Prfung der Haftfestigkeit von metallischen Beschichtungen durch Kugelstrahlen This European Standard was approved by CEN on 1994-12-05. CEN members are bound

11、to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Centr

12、al Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as t

13、he official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Euro

14、pen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B- 1050 Brussels O 1994 Copyright reserved to CEN members Ref. No. EN 2829 : 1994 E CEN EN*2829 94 3404589 0089377 149 m Page 2 EN 2829 : 1994 Foreword This European Standard has been prepared by the Europea

15、n Association of Aerospace Manufacturers (AECMA) . After inquiries and votes carried out in accordance with the rules of this Association, this standard has successively received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presen

16、tation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 1995, and conflicting national standards shall be withdrawn at the latest by June 1995. In accordance with the CENKENELEC intern

17、al Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom. CEN ENx2829 94 = 3404589 0087178 085 Pag

18、e 3 EN 2829 : 1994 1 Scope This standard specifies a test method to determine the adhesion of coatings by shot peening. It applies to ductile metal coatings, such as cadmium, silver or copper, with a hardness : - - 250 HV for a coating thickness between 10 pm and 60 pm It shall be applicable wheneve

19、r referenced 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications These nonnative references are cited at the appropriate places in the lext and the publications are listed hereafter For dated references, subsequent amendments to

20、 or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision For undated references lhe latest edition of the publicalion referred to applies EN 2409 Aerospace series - Shot peening for inducement of compressive surface stresses for

21、 metallic parts l) 3 Peening equipment - steel balls of approximately 0.3 mm. 0.5 mm or 0.6 mm diameter ; - any device fitted with a nozzle compatible with these balls - plales according lo EN 2409 type A 4 Procedure 4.1 Setting of the device The intensity and duration of peening shall be such that

22、a test plate (see 3) restrained flat between supports placed 32 mm apart. so that only one side is facing the shot stream, shows, when the restraint has been released, a deflection of . - (0.15 f 0.05) mm for a coating thickness 2 100 pm , - (0.25 f 0.05) mm for a coating thickness r 100 pm 4.2 Test

23、ing The coating applied to the test specimen or part is submitted lo peening according to 4.1 5 Fault sanction Neither Peeling nor blistering are permissible aHer visual inspection, with the naked eye or a magnification of max. six times In preparation at the date of publication of this standard CEN

24、 EN*S829 94 3404589 OOBL79 TLL Page 4 EN 2829 : 1994 6 Test mpott It shall include the following : reference to this standard ; reference to the part or test specimen nature of the coating ; thickness of the coating ; diameter of the balls used ; t deflection measured when setting the device ; lest

25、result. National annex NA (informative) Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted by the Engineering Sector Board to Technical Committee ACE/44 upon which the following bodies were represented: Aluminium Finishing Association B

26、ritish Coatings Federation Ltd. Metal Finishing Association Ministry of Defence National Centre of Tribology Oil and Colour Chemists Association Society of British Aerospace Companies Limited National annex NB (informative) Cross-reference Publication referred to EN 2409) Corresponding British Stand

27、ard BS EN 2409 Shot peening for inducement of compressive surface stresses for metallic parts )In preparation. CEN EN+2829 94 3404589 0089I18L 67T BS EN 2829 : 1995 BSI 389 Chiswick High Road London W4 4AL 9503 - 4 - 0.5k - FP BSI - British Standards Institution BSI is the independent national body

28、responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Contract requirements A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards

29、 are responsible for their correct application. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. Any person who finds an inaccuracy or ambiguity while using this British Standard should

30、bring it to the attention of the Quality Manager, BSI without delay so that the matter may be investigated swiftly. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI

31、, international and foreign standards publications should be addressed to Customer Services, Sales Department at Chiswick: RI: 0181 996 7000; k: 0181 996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as Br

32、itish Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library, the Standardline Database, the BSI Information Technology Service (Bm) and its lkchnical Help to Exporters Service. Co

33、ntact the Information Department at Chiswick: El: 0181 996 7111; k: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Customer Services, Membe

34、rship at Chiswick: Tel: 0181 996 7002; hx: 0181 996 7001. COPyright Copyright subsists in all BSI publications and no part may be reproduced in any form without the prior permission in writing of BSI. This does not preclude the free use, in the course of implementing the standard of necessary detail

35、s such as symbols and size, type or grade designations including use by incorporation into computer programs, but where these details are reproduced including without limitation in printed form, in computer programs or in any other form whatsoever, the permission in writing of MI must be obtained and if granted wii be on terms including royalty, before the product is sold, licensed or otherwise exploited for commercial gain. Enquiries about copyright should be made to the Copyright Manager at Chiswick. ISBN O Bso 2373 6 ACE144