ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:191.90KB ,
资源ID:710367      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-710367.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(EN 2831-1993 en Aerospace Series - Hydrogen Embrittlement of Steels - Test by Slow Bending《航空航天 钢的氢脆性 慢速弯曲试验》.pdf)为本站会员(terrorscript155)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

EN 2831-1993 en Aerospace Series - Hydrogen Embrittlement of Steels - Test by Slow Bending《航空航天 钢的氢脆性 慢速弯曲试验》.pdf

1、CEN ENa283L 93 m 3404589 0042656 T95 m EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2831:1993 February 1993 UOC 669.14:621.793/794:620.177:629.7 Descriptors: Airdt indwt, steels, hydrogen embriement, band tests English version Aerospace series - Hydrogen embrittiernent of steels - Test by sl

2、ow bending Srie arospatiale - Fragilisation des aclers par lhydrogne - Essa par flexion lente Luft- und Raumfahrt - Wasserstoffversprdung von Sthlen - Langsamer Biegeversuch This European standard was apptoved by CEN on 1993-02-19. CEN members are bound to comply with the =N/CENELEC Internal Regulat

3、ions which stipulate the conditions for giving this European Standard the status of a national standard withart any alteration. Up-to-date lists and bibliographic81 references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The Europ

4、ean Standards exist in three official versions (English. French. German). A version in any other language made by translation under the responsibillty of a CEN member into Its own language and notified to the Central Secretariat has the same status as the official versions. - CEN members are the nat

5、ional standards bodies of Austria, Belgium, Denmark, Finland, France. Germany, Greece, Iceland. Ireland, Italy, Luxembourg, Netherlands. Noway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Gmnittee for Standardization hit Europen de NonMlisation Europisches Komitee fur Normu

6、ng CenLral Su-etariat: rue de stascart.36 B-1050 the fixed chuck shall be fitted with an interchangeable bending block the diameter of which may be between 2 mm and 6 mm (see figure 1) ; the movable chuck shall have a deflection rate which can be adjusted between 4 O /min and 18 Olmin, - be fitted w

7、ith a device allowing to measure the angles ao, a fl and a f2 (see figures 2 to 41 with a precision of f 0,5O, - be fitted with a magnifier of 1 O times in order to reveal the occurence of the first crack. 3 lest specimens They shall : - be cut from a bar or sheet along the grain direction, - have t

8、he following dimensions : . length : 180 mm to 200 mm . width : 15 mm to 20 mm . thickness : 1,8 mm to 4 mm . straightness deflection over the length : 0.25 mm, - be machined along the grain direction to a surface roughness Ra s1,6 pm, then submitted to a stress relief of at least 2 h at 150 OC with

9、out decarburization. 4 Procedure Each bending angle (ao, a fl, if specified, and a f2) is determined successively on the same test specimen (see figures 2 to 4). At least three test specimens shall be used. The test specimens shall be in the same condition as the parts they represent. Page 4 EN 2831

10、:1993 CEN ENr2831 93 3404589 0042b59 7T4 = NOTE 1 : Test specimens, possibly of a different steel grade, with a higher strength than the pieces may be used: NOTE 2 : The fracture angle of the test specimens per bending shall not exceed the defiection angle of the movable chuck. The diameter of the b

11、ending block and the deflection rate of the movable chuck shall be determined according to the material and thickness of the test specimen. - Place the test specimen in the test machine (see figure 11. Bend the test specimen under the specified deflection rate of the movable chuck until the first cr

12、ack occurs in the centre part of the test specimen and measure the bending angles ao, a fl , if sgecified, and a f2. Angle a fl shall be measured within max. 1 h after surface treatment. 6 Expression of results - ductility after surface treatment : - final ductility : afl /ao x 100. in % af2 /ao x 1

13、00, in % 6 Fault sanction The value of final ductility shall be specified in the process standard. 7 Test report It shall include the following : - reference to this standard; - reference numbers of the test specimens; - nature of the coating; - thickness of the coating; - diameter of the bending bl

14、ock and deflection rate of the movable chuck; - values of bending angles measured; - test result. . I CEN EN12831 93 3404583 0042bb0 4Lb = Block 1 Ten specimen l i -3- EN 2831:1993 Block I - . Fixed *u& Movable chuck R of the bending block Figure 1 - Placing of the test specimen before testing * /- Detail W I- 1 Fiure 2 - Bending angle prior to chemical or electrolytic treatment (TJ Detail W - Mirror-view r, Detail W I - L I 7 Figure 3 - Bending angle after surface treatment

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1