EN 2997-007-2016 en Aerospace series - Connectors electrical circular coupled by threaded ring fire-resistant or non fire-resistant operating temperatures - 65 to 175 continuous 20.pdf

1、BS EN 2997-007:2016Aerospace series Connectors, electrical, circular,coupled by threaded ring, fire-resistant or non fire-resistant,operating temperatures 65C to 175 C continuous, 200 Ccontinuous, 260 C peakPart 007: Hermetic receptacle with roundflange attached by welding or brazing Product standar

2、dBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 2997-007:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 2997-007:2016. It supersedes BS EN 2997-007:2006 which is withdrawn.The UK participation in its preparation was

3、entrusted to Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are respons

4、ible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 92604 4 ICS 49.060 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards

5、Policy and Strategy Committee on 30 September 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 2997-007:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2997-007 September 2016 ICS 49.060 Supersedes EN 2997-007:2006English Version Aerospace series - Connec

6、tors, electrical, circular, coupled by threaded ring, fire-resistant or non fire-resistant, operating temperatures - 65 C to 175 C continuous, 200 C continuous, 260 C peak - Part 007: Hermetic receptacle with round flange attached by welding or brazing - Product standard Srie arospatiale - Connecteu

7、rs lectriques circulaires accouplement par bague filete, rsistant au feu ou non, tempratures dutilisation - 65 C 175 C continu, 200 C continu, 260 C en pointe - Partie 007 : Embase hermtique collerette ronde fixe par soudure ou brasure - Norme de produit Luft- und Raumfahrt - Elektrische Rundsteckve

8、rbinder mit Schraubkupplung, feuerbestndig oder nicht feuerbestndig, Betriebstemperaturen -65 C bis 175 C konstant, 200 C konstant, 260 C Spitze - Teil 007: Hermetischer fester Steckverbinder mit rundem Schwei- oder Ltflansch - Produktnorm This European Standard was approved by CEN on 4 April 2016.

9、CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on a

10、pplication to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC

11、 Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

12、Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue

13、Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2997-007:2016 EBS EN 2997-007:2016EN 2997-007:2016 (E) 2 Contents Page European foreword . 3 1 Scope 3 2 Normative references 4 3 Terms and definitions

14、 . 4 4 Required characteristics 4 5 Designation 8 6 Marking . 8 7 Technical specification 8 BS EN 2997-007:2016EN 2997-007:2016 (E) 3 European foreword This document (EN 2997-007:2016) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After

15、 enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a na

16、tional standard, either by publication of an identical text or by endorsement, at the latest by March 2017, and conflicting national standards shall be withdrawn at the latest by March 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

17、 rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 2997-007:2006. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European

18、Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia

19、, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 2997-007:2016EN 2997-007:2016 (E) 4 1 Scope This European Standard specifies the characteristics of hermetic receptacles with round flange attached by welding or brazing in the family of circular electrical connectors coupled by thre

20、aded ring. It applies to the class defined in Table 3. For plugs and protective covers, see EN 2997-008 and EN 2997-009 respectively. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated

21、references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2997-001, Aerospace series Connectors, electrical, circular, coupled by threaded ring, fire-resistant or non fire-resistant, operating temperatures

22、 65 C to 175 C continuous, 200 C continuous, 260 C peak Part 001: Technical specification EN 2997-002, Aerospace series Connectors, electrical, circular, coupled by threaded ring, fire-resistant or non fire-resistant, operating temperatures 65 C to 175 C continuous, 200 C continuous, 260 C peak Part

23、 002: Specification of performance and contact arrangements EN 2997-008, Aerospace series Connectors, electrical, circular, coupled by threaded ring, fire-resistant or non fire-resistant, operating temperatures 65 C to 175 C continuous, 200 C continuous, 260 C peak Part 008: Plug Product standard EN

24、 2997-009, Aerospace series Connectors, electrical, circular, coupled by threaded ring, fire-resistant or non fire-resistant, operating temperatures 65 C to 175 C continuous, 200 C continuous, 260 C peak Part 009: Protective cover for receptacle Product standard 3 Terms and definitions For the purpo

25、ses of this standard, the terms and definitions given in EN 2997-001 apply. 4 Required characteristics 4.1 Dimensions and mass See Figure 1 and Table 1. Dimensions are in millimetres; they apply after surface treatment. BS EN 2997-007:2016EN 2997-007:2016 (E) 5 Key 1 Panel 2 Thread 3 See EN 2997-001

26、. 4 Blue colour band minimum width 0,64 Figure 1 BS EN 2997-007:2016EN 2997-007:2016 (E) 6 Table 1 Housing size E G H W Mass Size contact 20 Size contacts 16 and 12 min. g max. 08 12,70 12,55 18,36 17,86 4,93 3,40 5,69 4,17 10,16 15 10 14,27 14,12 21,59 21,08 10,44 21 12 19,05 18,90 26,80 26,29 14,7

27、6 31 14 20,62 20,47 27,94 27,43 16,51 35 16 23,80 23,65 30,99 30,48 19,74 46 18 26,97 26,82 34,39 33,78 21,95 51 20 30,15 30,00 37,34 36,83 26,26 59 22 33,32 33,17 40,64 40,13 28,78 73 24 36,50 36,35 43,68 43,17 32,61 86 28 42,82 42,67 50,21 49,70 38,81 125 BS EN 2997-007:2016EN 2997-007:2016 (E) 7

28、4.2 Panel cut-out See Figure 2 and Table 2. Dimensions are in millimetres. Connector one Connector two X min. value is calculated as follows: D/2 connector one + D/2 connector two. (See Table 2 for value D) Figure 2 Table 2 Housing size A min. D min. 08 12,96 31,70 10 14,53 34,90 12 19,30 39,60 14 2

29、0,88 41,25 16 24,05 44,45 18 27,23 47,35 20 30,40 51,90 22 33,58 54,10 24 36,75 57,25 28 43,08 65,25 4.3 Material, surface treatment See Table 3. 4.4 Main general characteristics See EN 2997-002. BS EN 2997-007:2016EN 2997-007:2016 (E) 8 4.5 Possible combinations of plugs and receptacles See EN 2997

30、-002. 5 Designation EXAMPLE Description block ELECTRICAL CONNECTOR, RECEPTACLE Identity block EN2997Y11203MN Number of the basic standard Class (see Table 3) Hermetic receptacle with round flange (see EN 2997-002) Housing size and contact arrangement (see EN 2997-002) Type of contact: M = Solder cup

31、 male X = Eyelet male Polarization (see EN 2997-002) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. Table 3 Class and model connector Class Model description Y Hermetic receptacle with housing (shell) in passivated stainless steel, 500 h resis

32、tance to salt mist, solder contacts, maximum operating temperature 200 C continuous YE Hermetic receptacle with housing (shell) in passivated stainless steel, 500 h resistance to salt mist, solder contacts, maximum operating temperature 260 C peak 6 Marking Unless there are other specific contractua

33、l requirements, the marking shall include: the identity block as defined in Clause 5; the date of manufacture (year, week); the manufacturers name or trade mark. 7 Technical specification See EN 2997-001. This page deliberately left blankBSI is the national body responsible for preparing British Sta

34、ndards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, con

35、sumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sect

36、ors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standards

37、You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies

38、can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodi

39、es) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or

40、 any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored

41、 on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format i

42、s for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a

43、 subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subsc

44、ription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and

45、receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre rev

46、ised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as

47、soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find a

48、n inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Group Headquarters389 Chiswick High Road London W4 4AL UKBSI Back Cover.indd 1 27/01/2016 14:20