EN 3033-2008 en Aerospace series - Nuts self-locking hexagonal with captive washer in heat resisting steel FE-PA2601 (A286) uncoated - Classification 1 100 MPa 425 《航空航天系列 未涂覆FE-P.pdf

1、BRITISH STANDARDBS EN 3033:2008Aerospace series Nuts, self-locking, hexagonal with captive washer, in heat resisting steel FE-PA2601 (A286), uncoated Classification: 1 100 MPa/425 CICS 49.030.30g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38

2、g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 3033:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 May 2008 BSI 2008ISBN 978 0 580 60516 1National forewordThis British Standard is t

3、he UK implementation of EN 3033:2008. The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to

4、include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3033

5、April 2008 ICS 49.030.30 English Version Aerospace series - Nuts, self-locking, hexagonal with captive washer, in heat resisting steel FE-PA2601 (A286), uncoated - Classification : 1 100 MPa/425 C Srie arospatiale - Ecrous hexagonaux avec rondelle captive, auto-freinant, en acier rsistant chaud FE-P

6、A92HT (A286), non revtu - Classification: 1 100 MPa/425 C Luft- und Raumfahrt - Echskantmuttern, selbstsichernd mit Brdelscheibe, aus hochwarmfestem Stahl FE-PA2601 (A286), blank - Klasse: 1 100 MPa/425 C This European Standard was approved by CEN on 12 December 2007. CEN members are bound to comply

7、 with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Managemen

8、t Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the o

9、fficial versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia,

10、 Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reserved worldwide fo

11、r CEN national Members. Ref. No. EN 3033:2008: E2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Required characteristics.4 4 Designation 6 5 Marking .6 6 Technical specification and product qualification.6 BS EN 3033:20083 Foreword This document (EN 3033:2008) has been prepared by the

12、 Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD,

13、 prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at the latest by October 2008. Attention is d

14、rawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the follo

15、wing countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slov

16、enia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 3033:20084 1 Scope The standard specifies the dimensions of self-locking, uncoated hexagonal nuts with captive washer and MJ-thread in heat resisting steel FE-PA2601 (A286) for aerospace applications. Maximum test temperature of the part

17、s is 425 C. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 5855-1, Ae

18、rospace MJ threads Part 1: General requirements. ISO 5855-2, Aerospace MJ threads Part 2: Limit dimensions for bolts and nuts. EN 2399, Heat resisting steel FE-PA92-HT Rm 900 MPa Bars for forged bolts D 25 mm Aerospace series. 1)EN 2424, Aerospace series Marking of aerospace products. EN 2516, Aeros

19、pace series Passivation of corrosion resisting steels and decontamination of nickel base alloys. EN 3152, Aerospace series Nuts, self-locking, MJ threads, in heat resisting steel FE-PA2601 (A286), silver plated or uncoated Classification: 1 100 MPa (at ambient temperature) / 425 C Technical specific

20、ation. EN 3638, Aerospace series Heat resisting alloy FE-PA2601 (X6NiCrTiMoV26-15) Consumable electrode remelted Solution and precipitation treated Sheet, strip and plate 0,5 mm a 10 mm. EN 3639, Aerospace series Heat resisting alloy FE-PA2601 Softened and cold worked Wire for forged fasteners D 15

21、mm 900 MPa Rm 1 100 MPa.2)EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard parts. 3 Required characteristics 3.1 Configuration Dimensions Tolerances Configuration shall be in accordance with the Figure 1; dimensions, tolerances and masses shall conf

22、orm to Figure 1 and Table 1. Details of form not stated are at the manufacturers option. 1) Published as ASD Standard at the date of publication of this standard. 2) Published as ASD Prestandard at the date of publication of this standard. BS EN 3033:20085 3.2 Material Nut: Heat resisting steel FE-P

23、A2601 according to EN 2399, EN 3638 or EN 3639. Washer: Heat resisting steel FE-PA2601 according to EN 3638 or steel FE-PA3601. 3.3 Surface treatment Nut: None. Washer: Passivated to EN 2516. Threads surface will be achieved by normal methods of manufacture Break sharp edges 0,1 mm to 0,4 mm. Key 1

24、Bearing surface may be flat to concave, but shall not be convex 2 Washer shall be free to rotate on the nut 3 Form out-of-round in this area to achieve the self-locking torque requirements tool marks acceptable 4 Pitch diameter 5 Thread 6 Chamfer, radius or broken edge 7 Marking in those areas permi

25、ssible Figure 1 Configuration 6,3 1,6 BS EN 3033:20086 Table 1 Dimensions and masses Dimensions in millimetres E F b G H K L M N c y z d Diameter code Thread a min. nom. Tol. max. max. min. max. min. min. Mass kg/1 000Part 030 MJ30,5-4H6H 4,2 4 7,2 3,4 5,2 3,8 1,2 0,35 040 MJ40,7-4H6H 5,3 5 8,6 4,4

26、6,4 4,8 1,5 0,2 0,6 050 MJ50,8-4H6H 6,5 6 10,9 5,6 7,6 5,8 2 0,91 060 MJ61-4H5H 7,6 7 12,4 6,0 9 6,8 2,3 1,18 070 MJ71-4H5H 8,7 8 h12 13,9 6,9 11 8 2,7 0,1 1,77 080 MJ81-4H5H 10,9 10 15,4 7,8 12 9 3,2 3,43 100 MJ101,25-4H5H 13,2 12 18,6 9,6 14,7 11 3,8 5,2 120 MJ121,25-4H5H 15,5 14 h13 21,7 11,4 18,

27、5 13 0,4 4,5 0,15 0,4 10,7 aThread in conformity with ISO 5855-1 and ISO 5855-2. In the self-locking zone, the tolerances apply before forming out-of-round. bAcross flats dimensions apply before forming out-of-round, but finished nuts shall fit a standard socket wrench. cWrench pad engagement. dThes

28、e values apply before forming out-of-round. 4 Designation EXAMPLE Description block NUT Identity block EN3033-050 Number of this standard Diameter code (see Table 1) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 5 Marking Each hexagonal nut s

29、hall be marked in accordance to EN 2424, class F. 6 Technical specification and product qualification The hexagonal nuts shall be qualified in accordance with EN 9133, conforming to the requirements of EN 3152. BS EN 3033:2008blankBS EN 3033:2008BSI389 Chiswick High RoadLondonW4 4ALBSI British Stand

30、ards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Stand

31、ards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical

32、 committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standard

33、sOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards

34、, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Expo

35、rters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards develop

36、ments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standa

37、rds Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under t

38、he Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementi

39、ng the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.