EN 3059-2007 en Aerospace series - Bearings airframe rolling - Rigid single row ball bearings in steel with flanged alignment housing cadmium plated - Dimensions and loads《航空航天系列 飞.pdf

1、BRITISH STANDARDBS EN 3059:2007Aerospace series Bearings, airframe rolling Rigid single row ball bearings in steel with flanged alignment housing, cadmium plated Dimensions and loadsThe European Standard EN 3059:2007 has the status of a British StandardICS 49.035g49g50g3g38g50g51g60g44g49g42g3g58g44

2、g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 3059:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2007 BSI

3、 2007ISBN 978 0 580 56298 3National forewordThis British Standard is the UK implementation of EN 3059:2007.The UK participation in its preparation was entrusted to Technical Committee MCE/7, Rolling bearings.A list of organizations represented on this committee can be obtained on request to its secr

4、etary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARD

5、NORME EUROPENNEEUROPISCHE NORMEN 3059June 2007ICS 49.035English VersionAerospace series - Bearings, airframe rolling - Rigid single rowball bearings in steel with flanged alignment housing, cadmiumplated - Dimensions and loadsSrie arospatiale - Roulements pour structures daronefs- Roulements en acie

6、r, rigides, une range de billes, avecbague dalignement collerette cadmie - Dimensions etchargesLuft- und Raumfahrt - Flugwerklager - EinreihigeRillenkugellager aus Stahl mit selbsteinstellendem Flansch,verkadmet - Mae und BelastungenThis European Standard was approved by CEN on 16 March 2006.CEN mem

7、bers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on applicatio

8、n to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the

9、same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Ro

10、mania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedw

11、orldwide for CEN national Members.Ref. No. EN 3059:2007: E2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .5 4 Symbols and abbreviations 5 5 Required characteristics.5 6 Designation 10 7 Marking .10 8 Technical specification .10 EN 3059:20073 Foreword This docume

12、nt (EN 3059:2007) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Officia

13、l Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2007, and conflicting national standards shall be withdrawn at

14、 the latest by December 2007. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the n

15、ational standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norwa

16、y, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 3059:20074 1 Scope This standard specifies the characteristics of rigid single row ball bearings in steel, with cadmium-plated flanged alignment housing designed to withstand only slow rotations a

17、nd oscillations under load. They are intended for use in the hubs of torsion lever and in separated supports for airframe/aerospace applications. The airframe rolling bearings defined in this standard may be used in the temperature range from 54 C to 150 C. However, being lubricated with the followi

18、ng greases (see EN 3727): ester type very high pressure grease (code letter A), operating range from 73 C to 121 C or, synthetic hydrocarbons type very high pressure grease general purpose (code letter B) operating range from 54 C to 177 C. Their field of application when lubricated with code letter

19、 A grease is limited to 121 C. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) appl

20、ies. ISO 1132-1, Rolling bearings Tolerances Part 1: Terms and Definitions. EN 2031, Steel FE-PL31 Hardened and tempered Bars Aerospace series. 1)EN 2133, Aerospace series Cadmium plating of steels with specified tensile strength 1 450 MPa, copper, copper alloys and nickel alloys. EN 2221, Steel FE-

21、PL31 Hardened and tempered Hollow bars 3,5 mm a 55 mm Aerospace series. 1)EN 2222, Steel FE-PL31 Hardened and tempered Hand and die forgings Aerospace series. 1)EN 2249, Aerospace series Steel FE-PL52S Rm 690 MPa Bars De 250 mm. 2)EN 2424, Aerospace series Marking of aerospace products. EN 3727, Aer

22、ospace series Bearings, airframe rolling rigid with flanged alignment housing Technical specification. TR 4475, Aerospace series Bearings and mechanical transmissions for airframe applications Vocabulary. 3)1) Published as ASD Standard at the date of publication of this standard. 2) In preparation a

23、t the date of publication of this standard. 3) Published as ASDTechnical report at the date of publication of this standard. EN 3059:20075 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 1132-1 and TR 4475 apply. 4 Symbols and abbreviations dmp= sing

24、le plane mean bore diameter deviation ds= deviation of a single bore diameter Cs= permissible static radial load Famax.= permissible static axial load Ga= axial internal clearance Gr= radial internal clearance Sia= assembled bearing inner ring face runout with raceway Sea= assembled bearing outer ri

25、ng face runout with raceway Kia= radial runout of assembled bearing inner ring Kea= radial runout of assembled bearing outer ring 5 Required characteristics 5.1 Dimensions Clearances Masses Configuration and values: according to Figures 1 to 4 and Table 1; the bearings can be fitted with either seal

26、s or shields. The dimensions and tolerances are expressed in millimetres and apply after surface treatment. Key aIn both positions at 180 from the bearing Figure 1 EN 3059:20076 Key aTransition area at the manufacturers discretion Figure 2 Solid flanged alignment housing, code letter C Figure 3 Ligh

27、t weight flanged alignment housing, code letter D Type with shields code letter P Type with seals code letter E NOTE 1 Installation of seals and shields is at the manufacturers option. NOTE 2 The shields shall not extend beyond width C. Figure 4 EN 3059:20077 Table 1 d Tolerances m A B C D d1E E1r M

28、asses g/pieces Code number nom. dmpdsnom. 0,150 0,12 0,2 0,05 1 1 min.a 1 Code letter CCode letter D16 16 0 8 + 3 11 47 8 6 58 33 35 35 4 0 47 38 20 20 52 63 38 43 42 330 62 50 25 25 0 10 + 3 13 57 68 43 46 46 3 7 70 58 32 32 66 77 52 56 55 230 94 78 35 35 69 9 7 80 55 59 58 220 12 100 86 40 40 75 8

29、6 61 66 64 125 104 45 45 80 91 66 71 68 2 137 114 50 50 0 12 + 3 15 86 10 8 97 72 77 74 140 15 155 129 63 63 0 15 + 4 19 100 11 9 111 86 97 90 0,3 to 0,8 130 22 210 178 d Internal clearances bm Runout tolerances bmax. m Tilting torque N.m Starting torquebmax. mN.m Axial max. Radial Axial Radial Code

30、 number GaGrSiaSeaKiaKeaCode letter P Code letter E 16 3 to 11 8 12 20 9 14 25 0,8 to 3 12 21 32 21 30 35 1 to 4 27 35 40 33 44 45 1,3 to 4,5 39 53 50 1,5 to 5 48 68 63 120 5 to 13 40 40 25 40 2 to 6 83 113 aMaximum values for the user. bSee EN 3727. EN 3059:20078 5.2 Loads See Tables 2 and 3. Table

31、 2 Loads for bearings with code letter C alignment housing Permissible static loadsa kN Axial Radial Csfor a displacement of max.: for a displacement of max.: d Code number 0,1 mm 0,15 mm 0,2 mm 0,1 mm 0,15 mm 0,2 mm 16 15,2 20 18,7 25 20,6 32 24,5 35 1,32 1,78 2,16 1,8 2,5 3,2 25,5 40 1,3 1,75 2,13

32、 1,78 2,48 3,18 29,5 45 1,27 1,72 2,08 1,75 2,44 3,13 32,4 50 1,2 1,67 2 1,68 2,37 3,03 35,3 63 0,92 1,11 1,29 1,16 1,46 1,78 39,2 aAxial and radial loads may be applied simultaneously. For ultimate static loads, see EN 3727. EN 3059:20079 Table 3 Loads for bearings with code letter D alignment hous

33、ing Permissible static loadsa kN Axial Radial Csfor a displacement of max.: for a displacement of max.: d Code number 0,1 mm 0,15 mm 0,2 mm 0,1 mm 0,15 mm 0,2 mm 16 15,2 20 1,15 1,45 1,7 1,32 1,71 2,06 18,7 25 0,92 1,29 1,56 1,22 1,58 1,91 20,6 32 24,5 35 25,5 40 29,5 45 32,4 50 0,84 1,1 1,06 35,3 6

34、3 0,99 1,17 1,3 1,18 1,37 1,57 39,2 aAxial and radial loads may be applied simultaneously. For ultimate static loads, see EN 3727. 5.3 Surface roughness Raceways and rolling elements: Ra= 0,2 m Bore, side faces of the bearing and bearing/housing swivelling surface: Ra= 0,8 m Embedding diameter and s

35、upport face of the housing: Ra= 1,6 m General state: Ra= 3,2 m The values apply prior to cadmium plating. EN 3059:200710 5.4 Materials Flanged alignment housing: according to EN 2249, 900 MPa to 1 100 MPa Inner ring : according to EN 2031 or EN 2221 or EN 2222, 59 HRC to 64 HRC Outer ring : accordin

36、g to EN 2031 or EN 2221 or EN 2222, 59 HRC to 64 HRC Balls : according to EN 2031, 59 HRC to 64 HRC Shields : corrosion resisting material Seals : polytetrafluoroethylene (PTFE) or polytetrafluoroethylene (PTFE) reinforced with fibreglass. 5.5 Surface treatment of the bush According to EN 2133. Thic

37、kness 10 m to 20 m; internal spherical diameter is not cadmium plated. As soon as possible after plating, and within 16 h, de-embrittlement heat treatment shall be carried out at a temperature and for a time (compatible with the performance requirements of the bearing) which shall be subject to writ

38、ten approval of the qualifying authorities. 6 Designation EXAMPLE Description block BEARING Identity block EN3059A16PC Number of this standard Code letter for grease type (see Clause 1) Diameter code number of d (see Table 1) Type code letter (see Figure 4) Alignment housing code letter (see Figures

39、 2 and 3) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 7 Marking According to EN 2424, category A. Marking position and method are at the manufacturers option. 8 Technical specification According to EN 3727. EN 3059:2007blankBS EN 3059:2007B

40、SI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are upd

41、ated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British

42、 Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically rec

43、eive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.b

44、si-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standar

45、ds through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing memb

46、ers of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding

47、online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationa

48、l standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does n

49、ot preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright