1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 3264:2010Aerospace series Pipecoupling 830 in titanium alloy Thrust wire nutsProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,
2、-,-BS EN 3264:2010 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 3264:2010.It supersedes BS EN 3264:2001, which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/12, Aerospace fasteners and fastening systems. A list o
3、f organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2010 ISBN 978 0 580 65876 1 ICS 49.080 Compliance with a British Stan
4、dard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2010 Amendments issued since publicationDate T e x t a f f e c t e d Provided by IHSNot for ResaleNo reproduction or networking permitted
5、 without license from IHS-,-,-BS EN 3264:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3264 July 2010 ICS 49.080 Supersedes EN 3264:2001English Version Aerospace series - Pipe coupling 830 in titanium alloy - Thrust wire nuts Srie arospatiale - Systme de raccordement 830 en alliage de tit
6、ane - crous jonc Luft- und Raumfahrt - Rohrverschraubung 830 aus Titanlegierung - Muttern mit Schubdraht This European Standard was approved by CEN on 26 May 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standa
7、rd the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French,
8、 German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, C
9、yprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION
10、 COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3264:2010: EProvided by IHSNot for ResaleNo reproduction or ne
11、tworking permitted without license from IHS-,-,-BS EN 3264:2010EN 3264:2010 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Required characteristics .44 Designation 65 Marking .76 Technical specification .77 Qualification .7Provided by IHSNot for ResaleNo reproduction or networking
12、permitted without license from IHS-,-,-BS EN 3264:2010EN 3264:2010 (E) 3 Foreword This document (EN 3264:2010) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Asso
13、ciation, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsem
14、ent, at the latest by January 2010, and conflicting national standards shall be withdrawn at the latest by January 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identify
15、ing any or all such patent rights. This document supersedes EN 3264:2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Den
16、mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Provided by IHSNot for ResaleNo reproduction or networking p
17、ermitted without license from IHS-,-,-BS EN 3264:2010EN 3264:2010 (E) 4 1 Scope This European Standard specifies the characteristics of thrust wire nuts for pipe couplings 830, in titanium alloy, for aerospace applications. Nominal pressure: up to 28 000 kPa Temperature range: 55 C to 135 C 2 Normat
18、ive references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking
19、of aerospace products EN 2491, Aerospace series Molybdenum disulphide dry lubricants Coating methods EN 3275, Aerospace series Pipe coupling 830 up to 28 000 kPa Dynamic beam seal Metric series Technical specification EN 3311, Aerospace series Titanium alloy TI-P64001 (Ti-6Al-4V) Annealed Bar for ma
20、chining D 110 mm EN 3314, Aerospace series Titanium alloy TI-P64001 Solution treated and aged Bar for machining D 75 mm 1)EN 4032, Aerospace series Pipe coupling 830 in titanium alloy Thrust wire EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard part
21、s ISO 5855-3, Aerospace MJ threads Part 3: Limit dimensions for fittings for fluid systems ISO 8788, Aerospace Nuts, metric Tolerances of form and position 3 Required characteristics 3.1 Configuration Dimensions Mass According to Figure 1 and Table 1. The values apply before lubricating. 3.2 Surface
22、 roughness According to Figure 1. 1) Published as ASD-STAN Prestandard at the date of publication of this standard by Aerospace and Defence Industries Association of Europe-Standardization (ASD-STAN), (www.asd-stan.org). Provided by IHSNot for ResaleNo reproduction or networking permitted without li
23、cense from IHS-,-,-BS EN 3264:2010EN 3264:2010 (E) 5 3.3 Material According to EN 3311 or EN 3314 3.4 Surface treatment Lubrication: according to EN 2491, on the bottom of the groove only. Prior to application of the lubricant the surface shall be abrasive blasted using non-metallic grit. Film thick
24、ness: 0,005 mm to 0,013 mm Dimensions in millimetres aArea for marking bThread c0,3 to 0,5 applicable to both faces Figure 1 l1Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 3264:2010EN 3264:2010 (E) 6 Table 1 Dimensions in millimetres Codea T
25、hreadb d1 d2 d3 d4c e l1 l2 l3d l4l5m r s Te Mass g/piece 4H5H 0,1 0 0,2+ 0,1 0 + 0,1 0 min. 0,4 0,1 max. 0,1 h11 + 0,1 0 h13 max. 05 MJ10 1 9,1 11,0 2,2 15,51 4,2 7,2 8,4 10,0 13,01,3 14 0,36 5,52 06 MJ12 1,25 10,8 12,6 17,77 5,2 8,0 9,2 11,0 14,0 16 0,43 7,36 08 MJ14 1,5 12,6 17,0 14,6 20,03 11,0
26、6,2 9,5 11,0 13,0 16,0 18 7,59 10 MJ16 1,5 14,6 19,0 16,6 23,3610,57,210,5 12,014,016,5 21 9,00 12 MJ18 1,5 16,6 21,0 19,2 2,7 24,49 8,2 17,51,6 22 10,64 14 MJ20 1,5 18,6 23,0 21,2 26,75 9,2 18,0 24 0,52 11,56 16 MJ22 1,5 20,6 26,0 23,2 30,1410,010,214,519,027 17,50 18 MJ24 1,5 22,6 28,0 25,2 3,2 33
27、,53 11,21,9 30 23,66 20 MJ27 1,5 25,6 31,0 28,2 35,72 12,5 32 23,23 22 MJ30 1,5 28,6 35,0 31,2 39,98 13,7 36 27,72 25 MJ33 1,5 31,6 38,0 34,2 45,639,515,519,541 0,62 36,63 28 MJ36 1,5 34,6 41,0 37,2 51,28 17,2 46 42,00 32 MJ39 1,5 37,6 45,0 40,2 55,80 18,6 20,0 50 51,45 aCorresponds to the pipe nomi
28、nal outside diameter. bAccording to ISO 5855-3. cCorresponding wire diameter according to EN 4032. dMinimum usable thread length. eAccording to ISO 8788. 4 Designation EXAMPLE Description block THRUST WIRE NUT Identity block EN3264-05 Number of this standard Code (see Table 1) NOTE If necessary, the
29、 code I9005 shall be placed between the description block and the identity block. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 3264:2010EN 3264:2010 (E) 7 5 Marking According to EN 2424, style A and Figure 1. 6 Technical specification Accord
30、ing to EN 3275, type II. 7 Qualification According to EN 9133. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page deliberately left blankProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This pag
31、e deliberately left blankProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on st
32、andards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision.
33、Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Sec
34、retary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standa
35、rds.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer
36、Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of
37、information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20
38、 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Informati
39、on regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex
40、-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, i
41、n the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1