EN 3264-2018 en Aerospace series - Pipe coupling 8 - in titanium alloy - Thrust wire nuts.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Aerospace series - Pipe coupling 830 in titanium alloy - Thrust wire nutsBS EN 3264:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3264 June 2018 ICS 49.080 Supersedes EN 3264:2010English Version Aerospace ser

2、ies - Pipe coupling 830 in titanium alloy - Thrust wire nuts Srie arospatiale - Systme de raccordement 830 en alliage de titane - crous jonc Luft- und Raumfahrt - Rohrverschraubung 830 aus Titanlegierung - Muttern mit Schubdraht This European Standard was approved by CEN on 15 October 2017. CEN memb

3、ers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applicati

4、on to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Managem

5、ent Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

6、Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Rue de

7、la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3264:2018 ENational forewordThis British Standard is the UK implementation of EN 3264:2018. It supersedes BS EN 3264:2010, which is withdrawn.The U

8、K participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a c

9、ontract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 99056 4ICS 49.080Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the au

10、thority of the Standards Policy and Strategy Committee on 30 June 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 3264:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3264 June 2018 ICS 49.080 Supersedes EN 3264:2010English Version Aerospace series

11、 - Pipe coupling 830 in titanium alloy - Thrust wire nuts Srie arospatiale - Systme de raccordement 830 en alliage de titane - crous jonc Luft- und Raumfahrt - Rohrverschraubung 830 aus Titanlegierung - Muttern mit Schubdraht This European Standard was approved by CEN on 15 October 2017. CEN members

12、 are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application

13、to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

14、 Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lit

15、huania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Rue de la

16、Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3264:2018 EBS EN 3264:2018EN 3264:2018 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Required characteristics 4 4 Des

17、ignation 6 5 Marking . 6 6 Technical specification 7 7 Qualification 7 BS EN 3264:2018EN 3264:2018 (E) 3 European foreword This document (EN 3264:2018) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out

18、in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by public

19、ation of an identical text or by endorsement, at the latest by December 2018, and conflicting national standards shall be withdrawn at the latest by December 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be h

20、eld responsible for identifying any or all such patent rights. This document supersedes EN 3264:2010. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,

21、 Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey a

22、nd the United Kingdom. BS EN 3264:2018EN 3264:2018 (E) 4 1 Scope This document specifies the characteristics of thrust wire nuts for pipe couplings 830, in titanium alloy, for aerospace applications. Nominal pressure: up to 28 000 kPa. Temperature range: 55 C to 135 C. 2 Normative references The fol

23、lowing documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2

24、424, Aerospace series Marking of aerospace products EN 2491, Aerospace series Molybdenum disulphide dry lubricants Coating methods EN 3275, Aerospace series Pipe coupling 830 up to 28 000 kPa Dynamic beam seal Metric series Technical specification EN 3311, Aerospace series Titanium alloy TI-P64001 (

25、Ti-6Al-4V) Annealed Bar for machining D 110 mm EN 3314, Aerospace series Titanium alloy TI-P64001, solution treated and aged bar for machining D 75 mm EN 4032, Aerospace series Pipe coupling 830 in titanium alloy Thrust wires EN 9133, Aerospace series Quality Management Systems Qualification Procedu

26、re for Aerospace Standard Products EN ISO 286-2, Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts (ISO 286-2:2010) ISO 5855-3, Aerospace MJ threads Part 3: Limit dimensions f

27、or fittings for fluid systems ISO 8788, Aerospace Nuts, metric Tolerances of form and position 3 Required characteristics 3.1 Configuration Dimensions Mass According to Figure 1 and Table 1. The values apply before lubricating. 3.2 Surface roughness According to Figure 1. 3.3 Material According to E

28、N 3311 or EN 3314. BS EN 3264:2018EN 3264:2018 (E) 5 3.4 Surface treatment Lubrication: according to EN 2491, on the bottom of the groove only. Prior to application of the lubricant the surface shall be abrasive blasted using non-metallic grit. Film thickness: 0,005 mm to 0,013 mm. Dimensions in mil

29、limetres Key a Area for marking b Thread c 0,3 to 0,5 applicable to both faces Figure 1 BS EN 3264:2018EN 3264:2018 (E) 6 Table 1 Dimensions in millimetres CodeaThreadbd1d2d3d4ce l1l2l3dl4l5m r s TeMass g/piece 4H5H 0,1 00,2+0,10+0,10min. 0,4 0,1 max. 0,1 h11f+0,10h13fmax. 05 MJ10 1 9,1 11,0 2,2 15,

30、51 4,2 7,2 8,4 10,0 13,0 1,3 14 0,36 5,52 06 MJ12 1,25 10,8 12,6 17,77 5,2 8,0 9,2 11,0 14,0 16 0,43 7,36 08 MJ14 1,5 12,6 17,0 14,6 20,03 11,0 6,2 9,5 11,0 13,0 16,0 18 7,59 10 MJ16 1,5 14,6 19,0 16,6 23,36 10,5 7,2 10,5 12,0 14,0 16,5 21 9,00 12 MJ18 1,5 16,6 21,0 19,2 2,7 24,49 8,2 17,5 1,6 22 10

31、,64 14 MJ20 1,5 18,6 23,0 21,2 26,75 9,2 18,0 24 0,52 11,56 16 MJ22 1,5 20,6 26,0 23,2 30,14 10,0 10,2 14,5 19,0 27 17,50 18 MJ24 1,5 22,6 28,0 25,2 3,2 33,53 11,2 1,9 30 23,66 20 MJ27 1,5 25,6 31,0 28,2 35,72 12,5 32 23,23 22 MJ30 1,5 28,6 35,0 31,2 39,98 13,7 36 27,72 25 MJ33 1,5 31,6 38,0 34,2 45

32、,63 9,5 15,5 19,5 41 0,62 36,63 28 MJ36 1,5 34,6 41,0 37,2 51,28 17,2 46 42,00 32 MJ39 1,5 37,6 45,0 40,2 55,80 18,6 20,0 50 51,45 aCorresponds to the pipe nominal outside diameter. bAccording to ISO 5855-3. cCorresponding wire diameter according to EN 4032. dMinimum usable thread length. eAccording

33、 to ISO 8788. fh11 or h13 tolerance in accordance with ISO 286-2. 4 Designation EXAMPLE NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 5 Marking According to EN 2424, style A and Figure 1. BS EN 3264:2018EN 3264:2018 (E) 7 6 Technical specific

34、ation According to EN 3275, type II. 7 Qualification According to EN 9133. BS EN 3264:2018This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. Bri

35、tish Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The

36、knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge

37、 that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international

38、 standards, through our website at where hard copies can also be purchased.If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, inc

39、luding British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions bel

40、ow, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandard

41、s purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed a

42、t any one time. A single paper copy may be printed for personal or internal company use only. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional

43、 copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publicat

44、ions contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopte

45、d European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date.You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by be

46、coming a BSI Subscribing Member.PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced.To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visi

47、t a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur

48、British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: copyrigh