EN 3386-2012 en Aerospace series - Rings retaining radial mounting steel phosphated《航空航天系列 钢制径向安装固定含磷酸盐扣环》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 3386:2012Aerospace series Rings r e t a i n i n g , r a d i a l m o u n t i n g , steel, phosphatedBS EN 3386:2012 BRITISH STANDARDNational forewordThis British Standard is

2、 the UK implementation of EN 3386:2012. The UK participation in its preparation was entrusted to TechnicalCommittee ACE/12, Aerospace fasteners and fastening systems. A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport t

3、o include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012ISBN 978 0 580 75985 7 ICS 49.030.50 Compliance with a British Standard cannot confer immunity from legal obligations.

4、This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 3386:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3386 March 2012 ICS 49.030.50 English Version Aer

5、ospace series - Rings retaining, radial mounting, steel, phosphated Srie arospatiale - Anneaux darrt, montage radial, en acier, phosphats Luft- und Raumfahrt - Sicherungsringe, radial montierbar, aus Stahl, phosphatiert This European Standard was approved by CEN on 24 September 2011. CEN members are

6、 bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to t

7、he CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Cen

8、tre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Nor

9、way, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in

10、any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3386:2012: EBS EN 3386:2012EN 3386:2012 (E) 2 Contents Page Foreword . 31 Scope and field of application . 42 Normative references . 43 Required characteristics 43.1 Configuration Dimensions Masses 43.2 Materials . 43

11、.3 Surface treatment 44 Designation 65 Marking. 76 Technical specification . 77 Mounting 7BS EN 3386:2012EN 3386:2012 (E) 3 Foreword This document (EN 3386:2012) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes ca

12、rried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either

13、 by publication of an identical text or by endorsement, at the latest by September 2012, and conflicting national standards shall be withdrawn at the latest by September 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN an

14、d/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Cze

15、ch Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 3386:2012EN 3386:2012 (E) 4 1

16、Scope and field of application This standard defines the characteristics of radial mounting retaining rings, in steel, phosphated, for aerospace applications. These retaining rings are used only when EN 3384 cannot be used for installation problems. The phosphating restricts the use at temperatures

17、not exceeding 200 C. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document

18、 (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products EN 3380, Aerospace series Rings retaining Technical specification EN 3384, Aerospace series Rings, retaining, external, axial mounting, steel, phosphated 1)EN 3427, Aerospace series Groove dimensions for axi

19、al mounting external type retaining rings 3 Required characteristics 3.1 Configuration Dimensions Masses See figure 1 and table. The values shown in the table are applicable after phosphating. 3.2 Materials Spring steel: 480530 HV 3.3 Surface treatment Phosphate to EN 2793, class A Before storing, t

20、he ring shall be protected by grease or oil. 1) Published as ASD-STAN pre-standard at the date of publication of the present standard. BS EN 3386:2012EN 3386:2012 (E) 5 NOTE Details of form not stated are left to the manufacturers option. Key: a Installed b Free c Apply prior to phosphating Figure 1

21、 BS EN 3386:2012EN 3386:2012 (E) 6 Table 1 Dimensions in millimetres D1bD2D3S R P Mass cCode nom. H10 max. nom. Tol. kg/1 000 008 0,8 0,58 2 0,2 +0,02 0,04 0,1 0,003 012 1,2 1,01 3 0,3 0,009 015 1,5 1,28 4 0,4 0,021 019 1,9 1,61 4,5 0,5 0,040 023 2,3 1,94 6 0,6 0,069 032 3,2 2,7 7 0,088 040 4 3,34 9

22、 0,7 0,06 0,158050 5 4,11 11 0,07 0,236 060 6 5,26 12 0,08 0,255 070 7 5,84 14 0,9 0,474 080 8 6,52 16 1 +0,03 0,1 0,660 090 9 7,63 18,5 1,1 1,090 100 10 8,32 20 1,2 1,250 120 12 10,45 23 1,3 1,630 150 15 12,61 29 1,5 3,370 190 19 15,92 37 1,75 0,12 6,420 240 24 21,88 44 2 0,15 8,550 300 30 25,8 52

23、2,5 0,15 13,500 aValues apply after phosphating. bCorresponds to the diameter of the groove in which the ring shall be mounted (see EN 3427). cApproximate values, calculated on the basis of 7,85 kg/dm3, given for information purpose only. 4 Designation EXAMPLE Description blockRETAINING RING, RADIAL

24、 MOUNTING Identity block EN 3386 100 Number of EN Standard Diameter code (See table) NOTE If necessary, the originator code I9005 shall be placed between the description block and the identity block. BS EN 3386:2012EN 3386:2012 (E) 7 5 Marking EN 2424, style G. 6 Technical specification EN 3380 7 Mo

25、unting EN 3427 This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the internationa

26、l level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and

27、PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or

28、ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing M

29、embers an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit

30、card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standar

31、d implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing M

32、embers are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to Brit

33、ish Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some pe

34、rson or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in

35、 a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: