EN 3475-406-2002 en Aerospace Series - Cables Electrical Aircraft Use - Test Methods - Part 406 Cold Bend Test《航空航天系列 飞机用电缆 测试方法 第406部分 冷弯试验》.pdf

1、BRITISH STANDARD AEROSPACE SERIES Cables, electrical, aircraft use Test methods Part 406: Cold bend test The European Standard EN 3475-406:2002 has the status of a British Standard ICs 49.060 BS EN 3475406:2002 Wk present to the responsible European committee any enquiries on the interpretation, or

2、proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cr oss-r e fer enc e s The British Standards which

3、implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not

4、purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside fro

5、nt cover, the EN title page, pages 2 and 3 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. O BSI 05 February 2002 ISBN O 580 38363 6 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3475-406 January 2002 ICs 49.060 English version

6、Aerospace series - Cables, electrical, aircraft use - Test methods - Part 406: Cold bend test Srie arospatiale - Cbles lectriques usage aronautique - Mthodes dessai - Partie 406: Enroulement froid Luft- und Raumfahrt - Elektrische Leitungen fr Luftfahrt, Verwendung - Prfverfahren -Teil 406: Wickeln

7、bei Klte This European Standard was approved by CEN on 6 August 2001 CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographica

8、l references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN memb

9、er into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway,

10、Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FR NORMUNG COMIT EUROPEN DE NORMALISATION Management Centre: rue de Stassart, 36 B-1050 Brussels O 2002 CEN All rights of exploitation in any form and by any means reserved worldwide f

11、or CEN national Members. Ref. No. EN 3475-406:2002 E EN 3475-406:2002 (E) Foreword This document (EN 3475-406:2002) has been prepared by the European Association of Aerospace Manufacturers (AECMA). After enquiries and votes carried out in accordance with the rules of this Association, this Standard

12、has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by

13、July 2002, and conflicting national standards shall be withdrawn at the latest by July 2002. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard : Austria, Belgium, Czech Republic, Denmark, Fi

14、nland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 2 EN 3475-406:2002 (E) 1 Scope This standard specifies a method of determining the behaviour of a finished cable after a cold bend test. It sh

15、all be used together with EN 3475-100. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated referenc

16、es, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 3475-100 Aerospace series - Cables, electrical, aircraft

17、use - Test methods - Part 100: General EN 3475-302 Aerospace series - Cables, electrical, aircraft use - Test methods - Part 302: Voltage proof test 3 Preparation of a specimen Take a length of at least 750 mm from a finished cable. 4 Apparatus The test shall require a cold chamber and a supported h

18、orizontal mandrel. The mandrel diameter and mass shall be given in the technical specification. 5 Method 5.1 Procedure Unless otherwise indicated in the product standard, attach one of the ends of the specimen of at least 750 mm length to a horizontal mandrel and load the other end. Place the unit i

19、n a chamber at a temperature of (- 55 f 2) “C for 1 h. Turn the mandrel at the rate of 2 rpm to 3 rpm until the total length of the specimen is wound around the mandrel. Turn the mandrel in the opposite direction until the total length of the specimen is wound, the compressed part in the first opera

20、tion becoming the stretched part in the second. The cycle shall be performed twice. 5.2 After being returned to ambient temperature the cable insulation shall show no cracking or crazing. After completion of this test the specimen shall pass the voltage test defined in EN 3575-302. Req u i remen ts

21、3 BS EN 3475-406 12002 BSI 389 Chiswick High Road Lon don w4 4AL BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Re vi si ons British Standards are up

22、dated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Briti

23、sh Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically

24、receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: orders&-. Standards are also available from the BSI website at http:/ww

25、w.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international s

26、tandards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 71 11. Fax: +44 (0)20 8996 7048. Email: infomi-. Subscribi

27、ng members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details ofthese and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 700 1. Email: membershipbsi-. Information re

28、garding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, ofthe publications of

29、 the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise -without prior written permission

30、from BSI. This does not preclude the free use, in the course of implementing the standard, ofnecessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then the prior written permission ofBSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyright&-.