EN 3475-807-2002 en Aerospace Series - Cables Electrical Aircraft Use - Test Methods - Part 807 Transfer Impedance《航空航天系列 飞机用电缆 测试方法 第807部分 传输阻抗》.pdf

1、Cables, electrical, aircraft use Test methods Part 807: Transfer impedance The European Standard EN 3475-807:2002 has the status of a British Standard ICs 49.060 BS EN 3475-80712002 WbN present to the responsible European committee any enquiries on the interpretation, or proposals for change, and ke

2、ep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or Europea

3、n publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessa

4、ry provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not ofitself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages

5、2 to 5 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd.No. I Date I Comments O BSI 25 June 2002 ISBN O 580 39896 X EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3475-807 June 2002 ICs 49.0

6、60 English version Aerospace series - Cables, electrical, aircraft use - Test methods - Part 807: Transfer impedance Srie arospatiale - Cbles lectriques usage aronautique - Mthodes dessais - Partie 807: Impdance de transfert Luft- und Raumfahrt - Elektrischen Leitungen fr Luftfahrt Verwendung - Prfv

7、erfahren -Teil 807: Kupplungswiderstand This European Standard was approved by CEN on 1 March 2002 CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to

8、-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under th

9、e responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg

10、, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FR NORMUNG COMIT EUROPEN DE NORMALISATION Management Centre: rue de Stassart, 36 B-1050 Brussels O 2002 CEN All rights of exploitation in any form and by

11、any means reserved worldwide for CEN national Members. Ref. No. EN 3475-807:2002 E EN 3475-80712002 (E) Foreword This document (EN 3475-807:2002) has been prepared by the European Association of Aerospace Manufacturers (AECMA). After enquiries and votes carried out in accordance with the rules of th

12、is Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by

13、 endorsement, at the latest by December 2002, and conflicting national standards shall be withdrawn at the latest by December 2002. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria

14、, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 2 EN 3475-80712002 (E) 1 Scope This standard specifies methods for measuring the transfer impedance of a

15、 cable. It shall be used together with EN 3475-100. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For d

16、ated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 3475-100 Aerospace series - Cables, electric

17、al, aircraft use - Test methods - Part 100: General 3 Preparation of specimens These shall be stripped and prepared for connection to the measuring device required for the method chosen. 4 Methods 4.1 Simple method valid up to Method A: cable leakage method Q/m and 10 MHz - / I- 4 Matching resic tan

18、ce zo (to 1 %) - Copper box - Insulating supports - Test cable Place the length of test cable (approximately 1 m) in a sealed copper box with two lead-throughs as shown in figure 1 (dimensions 500 mm x 660 mm). The lead-throughs for the generator and microvoltmeter detector are as shown in figure 2.

19、 So that: V, = the generator voltage after the attenuator (input to cable) V = voltage detected Z, = value in ohms of characteristic impedance in common mode L = length of cable in metres; therefore: v. z, z, = - v,. L LGenerotor input L Output to microvol trne t er Figure 1 3 EN 3475-80712002 (E) _

20、-_-_-_ -_ Cable screening Cylindrical terminal end in red copper or foil 7 7,&/A I I m I For multicore cables, the two conductors shall be connected to each other at both ends. For multiscreened cables, these shall be connected to each other at both ends. Wall of the copper box Figure 2 The test cab

21、le shall be connected via its characteristic impedance Z,. Select a generator with the closest possible impedance to Z,. 4.2 Valid up to f = The conductors inside the screening, the transfer impedance of which is specified in the product standard, shall be connected together at both ends (figure 3).

22、 Method B: method of susceptible cable 30 - , where: L f is the frequency, in megahertz L is the cable length, in metres Cylindrical copper tube r Copper disc soldered to tube and to cable screening 7 Figure 3 G is a variable frequency power generator. V is a selective voltmeter (field intensity met

23、er) with input impedance ZI. The value of &A, is obtained either by direct measurement using a clamp-on current tester or by measuring UA, by the formula: R is a power limiting resistor U1 is the generator output voltage 4 EN 3475-80712002 (E) The short circuited elements are considered in the same

24、way as the conductor of a coaxial cable. See figure 4. The length of the cable inside the copper tube is L. The transfer impedance of the cable screening ZT is defined by the following theoretical formula: -66) IV.+. Figure 4 in which Vint. is the interference voltage appearing between the conductor

25、 and the screening. 5 The transfer impedance values ZT shall be below the values specified in the product standard. Req u i remen t 5 BS EN 3475-80712002 B SI 389 Chiswick High Road London w4 4AL BSI -British Standards Institution BSI is the independent national body responsible for preparing Britis

26、h Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is th

27、e constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cov

28、er. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be

29、 addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been pu

30、blished as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also availabl

31、e which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 71 11. Fax: +44 (0)20 8996 7048. Email: infomi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards.

32、 For details ofthese and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 700 1. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is

33、 available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be rep

34、roduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise -without prior written permission from BSI. This does not preclude the free use, in the course ofimplementing the standard, ofnecessary details such as symbols, and siz

35、e, type or grade designations. Ifthese details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.