EN 3683-2007 en Aerospace series - Test methods - Titanium alloy wrought products - Determination of primary a content - Point count method and line intercept method《航空航天系列的试验方法 钛合.pdf

1、BRITISH STANDARDBS EN 3683:2007Aerospace series Test methods Titanium alloy wrought products Determination of primary ! content Point count method and line intercept methodThe European Standard EN 3683:2007 has the status of a British StandardICS 49.025.30g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g

2、50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 3683:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2007 BSI 2007I

3、SBN 978 0 580 50597 3National forewordThis British Standard was published by BSI. It is the UK implementation of EN 3683:2007.The UK participation in its preparation was entrusted by Technical Committee ACE/61, Metallic materials for aerospace purposes, to Panel ACE/61/-/49, Titanium and its alloys.

4、A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from

5、legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 3683March 2007ICS 49.025.30English VersionAerospace series - Test methods - Titanium alloy wroughtproducts - Determination of primary a content - Point countmethod and line in

6、tercept methodSrie arospatiale - Mthodes dessais - Demi-produitscorroys en alliages de titane - Dtermination de la teneuren a primaire - Mthode par comptage de points etmthode par interception de lignesLuft- und Raumfahrt - Prfverfahren - Kneterzeugnisse ausTitanlegierungen - Bestimmung von Primr-a-

7、Anteilen -Punktzhlverfahren und LinienschnittverfahrenThis European Standard was approved by CEN on 5 October 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any a

8、lteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by tr

9、anslationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany

10、, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagem

11、ent Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3683:2007: E!2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Principle4 5 Sampling and sam

12、ple preparation.4 6 Test methods4 7 Expression of results 7 8 Test report 7 EN 3683:20073 Foreword This document (EN 3683:2007) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the r

13、ules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical te

14、xt or by endorsement, at the latest by September 2007, and conflicting national standards shall be withdrawn at the latest by September 2007. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held res

15、ponsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, Fra

16、nce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 3683:20074 1 Scope This standard specifies two methods, the point count method and t

17、he line intercept method, for optical microscope determination of primary content of titanium alloy wrought products, for aerospace applications. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition c

18、ited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3114-001, Aerospace series Test method Microstructure of ( + ) titanium alloy wrought products Part 001: General requirements. 3 Terms and definitions For the purposes of this s

19、tandard, the terms and definitions given in EN 3114-001 apply. 4 Principle Micrographic examination for determination of the primary content by: Counting the number of points of a specified point grid, enclosed in particles, point count method (Method A); Determining the lengths of lines of a specif

20、ied line grid intercepted by particles, line intercept method (Method B). 5 Sampling and sample preparation The test sample shall have a size such that the section to be examined shall not be less than 10 mm in diameter or square. The surface of the section shall be prepared according to EN 3114-001

21、. 6 Test methods 6.1 Point count method (Method A) Superimpose the specified point grid (see example in Figure 1) on the section to be examined. Adjust magnification so that each primary particle does not coincide with more than one point of the grid: Assessment is carried out as follows: all those

22、points on the grid which are enclosed by a primary particle are counted; a point lying exactly on a phase boundary is counted as 0,5 point; the sum N () of these points divided by the total number N of the grid points equals the amount of primary , Np; EN 3683:20075 Np corresponds to the volume (Vv)

23、 of primary on the surface area covered by the point grid. NpN)(NvV = See Figure 1 for an example of the calculation. Figure 1 Illustration of the point count method The diamonds represent particles. The dots represent points of the grid. The crosses represent points enclosed within particles. EXAMP

24、LE Total number of points in the grid N = 25 The number of points enclosed by an particle N () = 7 Calculation of the content of : 0,28257N)(NNp = The statistical error (Vv) is calculated as follows: NNp)(1Np2=Vv It is recommended that the count be carried out at several locations within the surface

25、 under examination to improve the accuracy of the determination by averaging. EN 3683:20076 6.2 Line intercept method (Method B) Superimpose the specified line grid (see example in Figure 2) on the section to be examined. Adjust magnification so that each primary particle in not intersected by more

26、than one grid line in each direction. Assessment is carried out as follows: the lengths of all portions of the grid lines which lie over an particle are added to produce the total S (); this count shall be carried out in both directions of the grid; the value S () divided by the total length S of al

27、l the grid lines within the surface under examination equals the grid line portion content NLattributable to the primary content and corresponds to the volume (Vv) of primary on the surface area covered by the line grid. VvS)(S = NLSee Figure 2 for an example of the calculation Figure 2 Illustration

28、 of the line intercept method The diamonds represent particles. The square lines represent the grid. a + b = the length of the grid lines S(). EN 3683:20077 EXAMPLE Total length of all grid lines S = 900 mm The total of all a and b lengths S() = 204 mm Calculation of the content of primary : 0,23900

29、204S)(S=The statistical error (Vv) is calculated as follows: Vv= 2 NLN11L)s(S(2+ where: s(S() is the standard deviation of line portion length distribution; L is the mean value of the line portion length; N is the number of intersected particles. It is recommended that the count be carried out at se

30、veral locations within the surface under examination to improve the accuracy of the determination by averaging. 7 Expression of results For each method, the individual or average values of primary content shall be given with the corresponding calculated statistical error. 8 Test report The test repo

31、rt shall refer to this standard and shall include: complete identification of the tested material, including the manufacturers name, designation and batch number; location of test sample; method of test sample preparation; all relevant test sample dimensions; date of test and traceability to individ

32、uals performing the test work; test method used: point count method (Method A) or line intercept method (Method B); equipment used: type of grid; number of locations sampled; test results (see Clause 7); any factor which may have affected the results and any deviation from the test method. EN 3683:2

33、007BS EN 3683:2007BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritis

34、h Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while

35、 using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscriber

36、s automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI web

37、site at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and in

38、ternational standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobs

39、i-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Inf

40、ormation regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications

41、of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission f

42、rom BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.