EN 3733-101-2008 en Aerospace series - Connector optical circular single channel coupled by self-locking ring operating temperature up to 150 Degree C continuous - Part 101 Protect.pdf

1、BS EN3733-101:2008ICS 49.060NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Connector, optical,circular, singlechannel, coupledby self-locking ring,operating temperatureup to 150 C continuousPart 101: Protective cover receptacle Product standard

2、This British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 3 2008 BSI 2008ISBN 978 0 580 60567 3Amendments/corrigenda issued since publicationDate CommentsBS EN 3733-101:2008National forewordThis British Standard is the UK implementation of EN 3733-101:2008

3、.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/6, Aerospace avionic electrical and fibre optictechnology.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary p

4、rovisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.0SeptemberBS EN 3733-101:2008EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3733-101 June 2008 ICS 49.060 English Version Aerospace series -

5、 Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous - Part 101: Protective cover receptacle - Product standard Srie arospatiale - Connecteur optique circulaire monovoie, accouplement par bague filete, tempratures dutilisation 150

6、C continu - Partie 101 : Bouchon de protection pour embase - Norme de produit Luft- und Raumfahrt - Optischer Rundsteckverbinder einpolig Schraubkupplung, Betriebstemperatur 150 C konstant - Teil 101: Schutzkappe fr Steckdose - Produktnorm This European Standard was approved by CEN on 14 March 2008.

7、 CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on

8、application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Cen

9、tre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Pola

10、nd, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by

11、 any means reserved worldwide for CEN national Members. Ref. No. EN 3733-101:2008: EBS EN 3733-101:2008EN 3733-101:2008 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Required characteristics.4 5 Designation 6 6 Marking .6 7 Technical specification .6 B

12、S EN 3733-101:2008EN 3733-101:2008 (E) 3 Foreword This document (EN 3733-101:2008) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has r

13、eceived the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Decemb

14、er 2008, and conflicting national standards shall be withdrawn at the latest by December 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent

15、 rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland

16、, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 3733-101:2008EN 3733-101:2008 (E) 4 1 Scope This standard specifies the characteristics of protective covers for single channel

17、fibre optic receptacle connectors four and two hole fixing, operating temperature up to 150 C. Connector interface dimensions, table of tests and qualification approval requirements, are contained in the Technical Specification EN 3733-001. EN 3733-002, List of product standards, includes the listin

18、gs of product types, codification and applicable combinations of product types. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the re

19、ferenced document (including any amendments) applies. EN 2591-100, Aerospace series Elements of electrical and optical connection Test methods Part 100: General. EN 3733-001, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150

20、C continuous Part 001: Technical specification.1)EN 3733-002, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 002: List of product standards. EN 3733-004, Aerospace series Connector, optical, circular, sin

21、gle channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 004: Receptacle, connector, four hole fixing for cable to EN 4532 Product standard. EN 3733-005, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating tempera

22、ture up to 150 C continuous Part 005: Receptacle, connector, two hole fixing for cable to EN 4532 Product standard. 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 2591-100 apply. 4 Required characteristics 4.1 Dimensions and mass Dimensions (in milli

23、metres) shall be as shown in Figure 1. 1) Published as ASD Prestandard at the date of publication of this standard. BS EN 3733-101:2008EN 3733-101:2008 (E) 5 Key 1 Over knurl 2 Seal 3 Cover rivet 4 3,2 cord 5 Eyelet 6 Cover shell 7 Size of fixing component (screw head or washer) not to exceed 10,0 m

24、m maximum. Figure 1 Mass: 17,9 g max. 4.2 Materials Nickel-copper alloy cover shell and rivet, nylon cord, fluorosilicone seal, cadmium plated copper eyelets. 4.3 Application combinations This protective cover is for use with Product Standards conforming to EN 3733-004 and EN 3733-005. See EN 3733-0

25、02 for applicable combinations of protective covers and connectors. 2 3 5 5 6 7 14,5 max. M111,0-6g1 18,6 max. 7,11 0,38 4 3,68 min. 9,97 max.76 7 BS EN 3733-101:2008EN 3733-101:2008 (E) 6 5 Designation EXAMPLE Description block COVER Identity block EN3733-101B Number of the basic standard Product s

26、tandard (see EN 3733-002) Class (see EN 3733-001, test fluids class B) NOTE 1 Part number spacing as shown is for clarity only. NOTE 2 If necessary, the code I9005 may be placed between the description block and the identity block. 6 Marking See EN 3733-001. 7 Technical specification Protective cove

27、rs are qualified when tested to the applicable qualification requirements of EN 3733-001. BS EN 3733-101:2008This page has been intentionally left blank BS EN3733-101:2008BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards Inst

28、itutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should

29、make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeerespo

30、nsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BS

31、I, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI

32、policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. V

33、arious BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial disc

34、ounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BS

35、I is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced,

36、stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: