EN 3745-516-2012 5000 Aerospace series - Fibres and cables optical aircraft use - Test methods - Part 516 Severe cable bend test《航空航天系列 航空器用光纤与光缆 试验方法 第516部分 严重的电缆弯曲试验》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 3745-516:2012Aerospace series Fibres andcables, optical, aircraft use Test methodsPart 516: Severe cable bend testCopyright European Committee for Standardization Provided

2、by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 3745-516:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 3745-516:2012.The UK participation in its preparation was entrusted to TechnicalCo

3、mmittee ACE/6, Aerospace avionic electrical and fibre optictechnology.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplicat

4、ion. The British Standards Institution 2012. Published by BSI StandardsLimited 2012ISBN 978 0 580 77591 8ICS 49.090Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on

5、31 July 2012.Amendments issued since publicationDate Text affectedCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 3745-516:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE

6、NORM EN 3745-516 July 2012 ICS 49.090 English Version Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 516: Severe cable bend test Srie arospatiale - Fibres et cbles optiques usage aronautique - Mthodes dessais - Partie 516: Essai de courbure svre Luft- und Raumfahrt

7、 - Faseroptische Leitungen fr Luftfahrzeuge - Prfverfahren - Teil 516: Schwere Kabelbiegeprfung This European Standard was approved by CEN on 23 March 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the

8、status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French

9、, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, C

10、roatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey an

11、d United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3745-5

12、16:2012: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 3745-516:2012EN 3745-516:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Preparation of spec

13、imens .44 Apparatus .45 Method 6Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 3745-516:2012EN 3745-516:2012 (E) 3 Foreword This document (EN 3745-516:2012) has been prepa

14、red by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countri

15、es of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2013, and conflicting national standards shall be withdrawn at the latest by January 2013. Atte

16、ntion is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organisations of

17、 the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Neth

18、erlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 3

19、745-516:2012EN 3745-516:2012 (E) 4 1 Scope This European Standard specifies a method of checking the break resistance and attenuation variation recovery of an optical cable subjected to severe bending under load. 2 Normative references The following documents, in whole or in part, are normatively re

20、ferenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591-100, Aerospace series Elements of electrical and optical connec

21、tion Test methods Part 100: General EN 3745-100, Aerospace series Fibres and cables, optical, aircraft use Test methods Part 100: General EN 3745-201, Aerospace series Fibres and cables, optical, aircraft use Test methods Part 201: Visual examination EN 3745-301, Aerospace series Fibres and cables,

22、optical, aircraft use Test methods Part 301: Attenuation 3 Preparation of specimens 3.1 If not yet at standard test conditions, the specimens shall be subjected to standard test conditions and stabilized at these conditions for 24 h as defined in EN 2591-100. Type and length of fibre or cable. Load

23、mass M to be applied to ensure contact between the cable and the edge of the metal bar. Radius(s) R of the bending edge. Number of turns N to rotate the cable 180 after each bend test. 4 Apparatus A Light Launch System (LLS) as defined in EN 2591-100. A Light Detection System (LDS) as defined in EN

24、2591-100. A flat metal bar with radius edge and loads required by the applicable product standard. A typical arrangement is shown in Figure 1. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license

25、from IHS-,-,-BS EN 3745-516:2012EN 3745-516:2012 (E) 5 Key 1 Extra restraining clamp (25,4 1,3) mm 2 Fibre optic cable 3 LLS 4 10 mm to 20 mm thick flat metal bar with radius edge R 5 Typical radius R = (127 25,4) m 6 Clamp 7 Load 8 LDS Figure 1 Copyright European Committee for Standardization Provi

26、ded by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 3745-516:2012EN 3745-516:2012 (E) 6 5 Method 5.1 Procedure a) Connect the specimen to the LLS and LDS. b) Attach the load mass (M) to the specimen as specified in the applicable

27、product standard prior to mounting the specimen on the bend fixture. c) Zero the LDS to establish a reference measurement. d) Mount the specimen on the bend fixture and gently apply the load to the specimen. e) After one (1) minute, measure the attenuation variation (EN 3745-301, method C) to ensure

28、 no fibber breakage. f) Remove the load from the cable and rotate the cable 180. g) Repeat steps d) through f) for the number of rotations required by the applicable product standard. h) Straighten specimen and measure the attenuation variation after one (1) minute. 5.2 Final measurements and requir

29、ements Measure the residual attenuation variation (EN 3745-301, method C) after removing the specimen from the test fixture to ensure no fibber breakage. Perform a visual examination according to EN 3745-201. Copyright European Committee for Standardization Provided by IHS under license with CENNot

30、for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page deliberately left blankCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BSI is the indepen

31、dent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products

32、 are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should

33、make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee respo

34、nsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically rece

35、ive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign stand

36、ards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on

37、standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the pur

38、chase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Stan

39、dards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisatio

40、n bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording

41、or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prio

42、r written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-