EN 40-6-2002 en Lighting Columns - Part 6 Requirements for Aluminium Lighting Columns《灯柱 第6部分 铝灯柱要求》.pdf

1、BRITISH STANDARD BS EN 40-612002 Lighting columns Part 6: Requirements for aluminium lighting columns The European Standard EN 40-6:2002 has the status of a British Standard ICs 77.150.10; 93.080.40 NO COPYING WITHOUT aSI PERMLSSION EXCEPT AS PERMITIED BY COPYRIGHT LAW British Standards BS EN 404:20

2、02 National foreword This British Standard is the official English language version ofEN 40-6:2002. It supersedes BS EN 40-6:2000 which is withdrawn. EN 40-6:2002 is a candidate “harmonized” European Standard and fully takes into account the requirements ofthe European Commission mandate W111, Circu

3、lation fixtures, given under the EU Construction Products Directive (89/106/EEC), and intended to lead to CE marking. The date ofapplicability of EN 40-6:2002 as a “harmonized” European Standard, i.e. the date after which this standard may be used for CE marking purposes, is subject to an announceme

4、nt in the meia1 Journal of the European Communities. EN 40-6:2002 is the subject of transitional arrangements agreed under the European Commission mandate. The Member States have agreed a nominal transition period for the Co-existence of EN 40-6:2002 and their corresponding national standard(s). It

5、is intended that this period will comprise a nominal nine month period during which any required changes to national regulations are to be made, followed by a further nominal twelve month period for the implementation of CE marking. At the end of this Co-existence period, the national standard(s) wi

6、ll be withdrawn. In the UK, there are nocorresponding national standards. The UKparticipation in its preparation was entrusted by Technical Committee B/509, Road equipment, to Subcommittee B/509/50, Road equipment - Street lighting columns, which has the responsibility to: This British Standard, hav

7、ing been prepared under the direction of the Building and Civil Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 17 July 2002 - - aid enquirers to understand the text; present to the responsible international/Europe

8、an committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this subcommittee can be obtained on request to its secretary

9、. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSIElectronic Catalogue o

10、r of British Stan dards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for their correct application. Compliance with a British Standard does not ofitself confer immunity from legal obligations. Summary of pages This document co

11、mprises a front cover, an inside front cover, the EN title page, pages 23 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication OBSI 17 July 2002 ISBN O 580 40083 2 Amd. No. I Date I Comments EUROPEAN STAN

12、DARD NORME EUROPENNE EUROPISCHE NORM EN 40-6 April 2002 ICs 77.150.10; 93.080.40 Supersedes EN 40-6:2000 English version Lighting columns - Part 6: Requirements for aluminium lighting col um ns Candlabres dclairage public - Partie 6: Exigences pour les candlabres dclairage public en aluminium Lichtm

13、aste - Teil 6: Anforderungen fr Lichtmaste aus Aluminium This European Standard was approved by CEN on 25 February 2002. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without

14、 any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made b

15、y translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Irel

16、and, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FR NORMUNG COMIT EUROPEN DE NORMALISATION Management Centre: rue de Stassart, 36 B-1050 Brussels O 2002 CEN All rights of exploitati

17、on in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 40-6:2002 E EN 40-62002 (E) Contents Foreword 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Scope Normative references Terms and definitions Materials Dimensions Design and design verification Welding Joints Protection

18、 against mechanical impact Internal finish and sharp edges Corrosion protection Marking Conformity control Acceptance criteria Re-testing Performance under vehicle impact - Passive safety 4 4 5 6 6 6 6 7 7 8 8 9 9 13 14 15 Annex A (informative) Corrosion protection for aluminium lighting columns 16

19、Annex B (informative) Recommendations for storage and installation 17 Annex C (normative) Initial type tests 18 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive 19 2 EN 40-62002 (E) Foreword This document EN 40-6:2002 has be

20、en prepared by Technical Committee CEN/TC 50 “Lighting columns and spigots“, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2002, and conflicting

21、national standards shall be withdrawn at the latest by January 2004. This document supercedes EN 40-6:2000. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association and supports essential requirements of EU Directive 89/106/EEC.

22、For relationship with EU Directive 89/106/EEC see informative annex ZA which is an integral part of this document. In this standard the annexes A and B are informative and the annex C is normative. Wherever reference is made to classes, they are considered to be technical classes and not classes acc

23、ording to 3(2) of the Construction Products Directive. This European Standard is the sixth in a series relating to specifications for lighting columns. At present the Parts of this standard are as follows: Part 1 : Definitions and terms Part 2: General requirements and dimensions Part 3: Design and

24、verification 3-11 Specification for characteristic loads 3-2: Verification by testing 3-3: Verification by calculation Part 4: Requirements for reinforced and prestressed concrete lighting columns Part 5: Requirements for steel lighting columns Part 6: Requirements for aluminium lighting columns Par

25、t 7: Requirements for fibre reinforced polymer composite lighting columns According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germa

26、ny, Greece, Iceland, Ireland, Italy, 3 EN 40-62002 (E) Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 1 Scope This European Standard specifies requirements for aluminium lighting columns. It includes materials and conformity control. It applies t

27、o post top columns not exceeding 20 m height for post top lanterns and to columns with brackets not exceeding 18 m height for side entry lanterns. This European Standard specifies performance related to the essential requirements of resistance to horizontal (wind) loads and performance under vehicle

28、 impact (passive safety) in support of the Essential Requirement No 4 Safety in use measured according to the corresponding test methods included in this European Standard or available in separate European Standards. It provides for the evaluation of conformity of the products to this European Stand

29、ard. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or

30、 revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 40-1 prEN 40-2: 1999 EN 40-3-1 EN 40-3-2 prEN 40-3-3 EN 288-1 EN

31、288-2 Lighting columns - Part 1 : Definitions and terms. Lighting columns - Part 2: General requirements and dimensions. Lighting columns - Design and verification - Part 3-1: Specification for characteristic loads. Lighting columns - Design and verification - Part 3-2: Verification by testing. Ligh

32、ting columns - Design and verification - Part 3-3: Verification by calculation. Specification and approval of welding procedures for metallic materials - Part 1 : General rules for fusion welding. Specification and approval of welding procedures for metallic materials - Part 2: Welding procedures sp

33、ecification for arc welding. 4 EN 40-62002 (E) EN 288-4 EN 288-8 EN 485-3 EN 485-4 EN 571-1 EN 755-7 EN 755-8 EN 970 EN 1011-1 EN 1011-4 EN 1706 EN 10025 EN 10204 EN 12767 EN 50 102 Specification and approval of welding procedures for metallic materials - Part 4: Welding procedure tests for the arc

34、welding of aluminium and its alloys. Specification and approval of welding procedures for metallic materials - Part 8: Approval by a pre-production welding test. Aluminium and aluminium alloys - Sheet, strip and plates -Part 3: Tolerances on shape and dimensions for hot rolled products. Aluminium an

35、d aluminium alloys - Sheet, strip and plates - Part 4: Tolerances on shape and dimensions for cold rolled products. Non-destructive testing - Penetrant testing - General principles. Aluminium and aluminium alloys - Extruded rodhar, tube and profiles - Part 7: Seamless tubes, tolerances on dimension

36、and form. Aluminium and aluminium alloys - Extruded rodhar, tube and profiles - Part 8: Porthole tubes, tolerances on dimensions and form. Non-destructive examination of fusion welds - Visual examination. Welding - Recommendations for welding of metallic materials - General guidance for arc welding.

37、 Welding - Recommendations for welding of metallic materials - Arc welding of aluminium and aluminium alloys. Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties. Hot rolled products of non-alloy structural steels - Technical delivery conditions. Metallic produ

38、cts - Types of inspection documents. Passive safety of support structures for road equipment - Requirements and test methods. Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code). 3 Terms and definitions For the purposes of this European

39、 Standard, the terms and definitions given in EN 40-1 apply. 5 EN 40-62002 (E) 4 Materials 4.1 Aluminium Materials used shall comply with one of the following standards: EN 485-3, EN 485-4, EN 755-7, EN 755-8 and EN 1706. Electrolytic action between the foundation bolts and the flange plate shall be

40、 prevented by insulation or physical separation. 4.2 Foundation bolts The minimm mechanical properties of the steel used for foundation bolts shall comply with the requirements of EN 10025 grade S 235 JR. 5 Dimensions Dimensions shall be in accordance with prEN 40-2. 6 Design and design verification

41、 The column shall be designed to sustain safely the dead loads and the wind loads specified in EN 40-3-1. The structural design of a lighting column shall be verified either by calculation in accordance with prEN 40-3-3 or by testing in accordance with EN 40-3-2. 7 Welding 7.1 Welding process Arc we

42、lding of aluminium and its alloys shall be in accordance with EN 1 O 1 1 - 1 and prEN 101 1-4. 7.2 Welding procedures Welding procedures shall comply with EN 288-1 and EN 288-2. Written procedures shall be provided for the main structural joints which shall include where relevant the flange plate jo

43、int, the base compartment to shaft joint, the door reinforcement, any intermediate column joint, the column to bracket joint and the column seam weld when this is carried out at the time of column manufacture. 6 EN 40-62002 (E) Welding procedures shall be approved in accordance with EN 288-8. Pre-pr

44、oduction test pieces shall represent the main structural joints. Welding procedures shall be verified by testing to the requirements of EN 288-4. The welding consumables and procedures used shall be such that the mechanical properties of the as- deposited weld metal will not be less than the respect

45、ive minimum values required by the designers specifications for the parent metal to be welded. Verification shall be by a welding Co-ordinator. Procedures shall be reviewed and reapproved where necessary after a period of seven years. 7.3 Welding personnel Welders shall be tested for each approved p

46、rocedure to which they shall be required to work (see 7.2). Test pieces shall be as used in the original procedure tests. The approval range shall be in accordance with that for the original procedure. 8 Joints 8.1 General All joints shall be designed to the requirements specified in clause 6. NOTE

47、Design of joint details should avoid moisture retention and corrosion. 8.2 Friction joints When joints are made by drawing parts together to form a friction joint the additional stresses in the connection shall be included in the design. 8.3 Welded joints Welded joints shall comply with the requirem

48、ents of clause 7. 9 Protection against mechanical impact A type test shall be carried out on each type of column base, or part, provided that each end of the part extends at least 0,3 m above and below the door opening. The test shall comply with an impact protection category of KO8 as specified in

49、EN 50 102 with the door fitted. The test equipment shall be either impact pendulum hammer or vertical free fall hammer. The number of impacts shall be five and shall be applied around the circumference at the mid height of the door. For circular columns these shall be equi-spaced around the remaining circumference excluding the door. For octagonal columns these shall be on each of the adjacent faces excluding the door. 7 EN 40-62002 (E) After testing there shall be no indentation greater than 3 mm in depth when measured with a profile gauge. The test validates those produc