EN 4056-001-2015 en Aerospace series - Cable ties for harnesses - Part 001 Technical specification《航空航天系列 导线电缆扎匝 第001部分 技术规范》.pdf

1、BSI Standards PublicationBS EN 4056-001:2015Aerospace series Cable tiesfor harnessesPart 001: Technical specificationBS EN 4056-001:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 4056-001:2015.It supersedes BS EN 4056-001:2006 which is withdrawn.The UK par

2、ticipation in its preparation was entrusted to TechnicalCommittee ACE/6, Aerospace avionic electrical and fibre optictechnology.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of

3、 a contract. Users are responsible for its correctapplication. The British Standards Institution 2015. Published by BSI StandardsLimited 2015ISBN 978 0 580 86331 8ICS 49.060Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the a

4、uthority of theStandards Policy and Strategy Committee on 30 June 2015.Amendments issued since publicationDate Text affectedBS EN 4056-001:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4056-001 June 2015 ICS 49.060 Supersedes EN 4056-001:2006English Version Aerospace series - Cable ties f

5、or harnesses - Part 001: Technical specification Srie arospatiale - Frettes de cblage pour harnais - Partie 001: Spcification technique Luft- und Raumfahrt - Befestigungsbnder fr Leitungsbndel - Teil 001: Technische Lieferbedingungen This European Standard was approved by CEN on 28 June 2014. CEN me

6、mbers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applica

7、tion to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Manag

8、ement Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia

9、, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix

10、 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4056-001:2015 EBS EN 4056-001:2015EN 4056-001:2015 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Conditions

11、of use.5 5 Descriptions and design .5 6 Tests 6 7 Quality assurance 8 8 Designation and marking 9 9 Packaging and storage 10 BS EN 4056-001:2015EN 4056-001:2015 (E) 3 Foreword This document (EN 4056-001:2015) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardi

12、zation (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be

13、given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2015, and conflicting national standards shall be withdrawn at the latest by December 2015. Attention is drawn to the possibility that some of the elements of this documen

14、t may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 4056-001:2006. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bou

15、nd to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portuga

16、l, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 4056-001:2015EN 4056-001:2015 (E) 4 1 Scope This European Standard specifies the characteristics, test methods, qualification and acceptance conditions of plastic cable ties, used for the bundling, fixin

17、g and/or marking of cable harnesses in aircraft. The cable ties should be installed with a qualified application tool, which controls the application force thus avoiding damage to the cable insulation. It defines the aerospace requirements not specified in EN 62275. 2 Normative references The follow

18、ing documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospac

19、e series Marking of aerospace products EN 2825, Aerospace series Burning behaviour of non metallic materials under the influence of radiating heat and flames Determination of smoke densityEN 2826, Aerospace series Burning behaviour of non metallic materials under the influence of radiating heat and

20、flames Determination of gas components in the smokeEN 3475-100, Aerospace series Cables, electrical, aircraft use Test methods Part 100: General EN 4056-002, Aerospace series Cable ties for harnesses Part 002: Index of product standards EN 4057 (all parts), Aerospace series Cable ties for harnesses

21、Test methods EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard parts EN 62275, Cable management systems Cable ties for electrical installations ISO 8815, Aircraft Electrical Cables and Cable Harnesses Vocabulary MS 90387, Tool, hand, adjustable for p

22、lastic and metal tie down straps 1)3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN 3475-100 and ISO 8815 and the following apply. 3.1 cable loom or cable harness any assembly of cables, complete with end terminals, which may be manufactured and formed

23、 on or off the aircraft, with two or more end destinations 3.2 cable bundle any group of cables which are tied together 1) Published by: DoD National (US) Mil. Department of Defense. http:/www.defenselink.mil/ BS EN 4056-001:2015EN 4056-001:2015 (E) 5 4 Conditions of use 4.1 Temperature ratings (typ

24、e) The ties shall be capable of use within the temperature range specified in the product standards. Temperature ratings shall be defined by the material codes specified in EN 4056-002. 4.2 Flammability class Ties shall meet either class 1 or class 2 flammability requirements as defined Table 2 test

25、 EN 4057-302 and in the appropriate product standard: Class 1 has the highest degree of flame retardant properties; Class 2 has a lower degree of flame retardant properties. 5 Descriptions and design 5.1 Description Ties, see Figure 1, shall be designed for installation by a tool providing controlle

26、d tension in accordance with MS 90387. The head design, locking system and strap cross sectional dimensions shall be such that the requirements of the tests given in Clause 6 are met. Ties are available with plastic or metallic locking mechanisms and those with plastic locking mechanisms may have ei

27、ther internal or external serrations on the strap. Figure 1 BS EN 4056-001:2015EN 4056-001:2015 (E) 6 5.2 Design and manufacture The finish shall prevent abrasion to the harness and to adjacent harnesses or breakouts. In completing the joint, no sharp or abrasive edges shall be formed that could dam

28、age the cable insulation of the loom or any adjacent looms, or that could cause injury to an operator. 5.3 Materials Ties shall be made from virgin materials which may be formulated to be UV resistant. The use of in process reground material to a maximum of 25 % by mass is permissible but is limited

29、 to the percentage used in the qualification sample. Materials shall be identified by the codes in EN 4056-002. 5.4 Colour Ties shall be either natural or un-pigmented material finish or a colour according to the codes shown in Table 1. Table 1 Colour codes Code Colour 0 Black 1 Brown 2 Red 3 Orange

30、 4 Yellow 5 Green 6 Blue 7 Violet 8 Grey 9 Natural/un-pigmented The colour shall be uniform throughout any coloured tie. 6 Tests All non-metallic materials used for the manufacture of cable ties shall be tested for their smoke and toxicity properties in accordance with EN 2825 and EN 2826 as defined

31、 in the product standard. Finished products shall be tested as detailed in Table 2 and the product standard. Before commencement of these tests the calibration of the application tools to be used shall be verified in accordance with EN 4057-407. BS EN 4056-001:2015EN 4056-001:2015 (E) 7 Table 2 Test

32、s (1 of 2) EN 4057- Designation of the test Number of specimens Details 201 Visual examination All test specimens to be examined. There shall be no sharp or abrasive edges. 202 Examination of mass and dimensions All test specimens to be tested. The mass and dimensions shall be in accordance with the

33、 product standard. 301 Salt mist test (applicable to ties containing metallic locking barbs) 3 specimens for each cross section grouping (i.e. loop tensile strength group). The minimum loop tensile strength shall be in accordance with the product standard. The locking device shall show no sign of co

34、rrosion. 302 Flammability 3 specimens (see Table 5) of the largest cross-section each material code. (i.e. loop tensile strength group) aAfter removal of the burner from the specimen, any flame shall extinguish within 5 s. If there are no flaming droplets (or particles) during the test, and the flam

35、e extinguishes within 5 s, the specimen will be classified as Class 1. If there are flaming droplets (or particles) but all the flames extinguish within 5 s, the specimen will be classified as Class 2. 303 Resistance to fluids 3 specimens for each material type and or class for each of the test solu

36、tions. The minimum loop tensile strength should be in accordance with the product standard. 304 Loop tensile strength at maximum working temperature 3 specimens for each cross section grouping (see Table 5) (i.e. loop tensile strength group). The minimum loop tensile strength should be in accordance

37、 with the product standard. 305 Colour fastness (applicable only to coloured ties) 1 specimen per colour, material type and material class. The colour fastness of the specimen should be in accordance with the product standard. 306 Heat ageing test 3 specimens for each material code and cross section

38、 group. The tensile strength shall not be lower than that specified in the appropriate product standard 307 Resistance to ultra violet radiation As detailed. The average elongation at break of the exposed samples shall be not less than 60 % of the figure for the unexposed samples. 401 Loop tensile s

39、trength 3 specimens per cross section grouping (see Table 5). The minimum loop tensile strength shall be in accordance with the product standard. BS EN 4056-001:2015EN 4056-001:2015 (E) 8 Table 2 Tests (2 of 2) EN 4057- Designation of the test Number of specimens Details 402 Life cycle Specimens for

40、 each cross section grouping (see Table 5) (i.e. loop tensile strength group). 1. There shall be no damage to the cable insulation when viewed with a 10 times magnification aid. 2. The specimens shall be examined for cracks, breaking and/or release of the locking device during removal from the vibra

41、tion test harness. 3. The minimum loop tensile strength shall be in accordance with the product standard. 404 Low temperature installation 3 specimens for each cross section grouping (see Table 5) (i.e. loop tensile strength group). The minimum loop tensile strength shall be in accordance with the p

42、roduct standard. 405 Compass safe distance (applicable to ties containing metallic locking barbs) 1 specimen The compass safe distance shall not exceed 125 mm. 406 Locking device retention (applicable to ties containing metallic locking barbs) 3 specimens The force to pull out the barb from the tie

43、head shall meet the requirement of the appropriate product standard. 407 Verification of application tool settings 5 specimens a At the appropriate setting the reading for all 5 specimens shall be as detailed in the product standard 100%. aSmall sizes may contain insufficient mass for these tests to

44、 be performed satisfactorily. 7 Quality assurance 7.1 General conditions Quality assurance conditions shall conform to EN 9133. 7.2 Qualification testing All the applicable tests in Table 3 shall be performed on all types, classes and colours of product at the commencement of manufacture, the use of

45、 new manufacturing tooling or change of raw material. These tests shall also be carried out at the re-commencement of production in the event of a stoppage longer than three years. 7.3 Maintenance of qualification For products in continuous production, the tests in Table 3, maintenance of qualificat

46、ion, shall be performed every three years. BS EN 4056-001:2015EN 4056-001:2015 (E) 9 Table 3 Maintenance of qualification EN 4057- Designation of the test Number of specimens 201 Visual examination 6 specimens to be tested 202 Examination of mass and dimensions 3 specimens to be tested 306 Heat agei

47、ng 3 specimens to be tested 401 Loop tensile strength 3 specimens to be tested 406 Locking device retention a3 specimens to be tested aOnly for cable ties with metal locking barbs. 7.4 Acceptance testing Samples should be taken at random in every batch and a test should be carried out as shown in Ta

48、ble 4. Table 4 Acceptance EN 4057- Designation of the test Number of specimens 201 Visual examination 6 specimens to be tested 202 Examination of mass and dimensions 3 specimens to be tested. Dimensions only. 401 Loop tensile strength 3 specimens per batch 8 Designation and marking 8.1 Marking The m

49、anufacturers monogram in accordance with EN 2424, style F shall be marked on the strap of the tie as close to the head as possible such that it is on the outside of the cable bundle after installation. 8.2 Designation EXAMPLE Description block CABLE TIE Identity block EN4056-001A1P1A Number of this standard Material code (see EN 4056-002) Flammability class (see 4.2) Size code (see Table 5) Colour code (see Table 1) Variant code (see Table 6) BS EN 4056-001:2015EN 4056-001:2015 (E) 10 Table 5 Size code Size code Recommend