EN 4115-2010 en Aerospace series - Cushion rubber for clamps - Dimensions masses《航空航天系列 夹具橡胶垫 尺寸和重量》.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 4115:2010Aerospace series Cushion,rubber for clamps Dimensions, massesBS EN 4115:2010 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN

2、4115:2010.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovi

3、sions of a contract. Users are responsible for its correctapplication. BSI 2010ISBN 978 0 580 59239 3ICS 49.025.40; 49.030.99Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Com

4、mittee on 31 July 2010Amendments issued since publicationDate Text affectedBS EN 4115:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4115 April 2010 ICS 49.025.40; 49.030.99 Supersedes EN 4115:2001English Version Aerospace series - Cushion, rubber for clamps - Dimensions, masses Srie arosp

5、atiale - Profil en lastomre pour colliers - Dimensions, masses Luft- und Raumfahrt - Profilgummi fr Schellen - Mae, Massen This European Standard was approved by CEN on 16 January 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for givin

6、g this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official vers

7、ions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium

8、, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITT

9、EE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4115:2010: EBS EN 4115:2010EN 4115:2010

10、(E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Required characteristics .54 Designation 75 Marking .86 Quality assurance 87 Technical specification .88 Packaging .8Bibliography 9BS EN 4115:2010EN 4115:2010 (E) 3 Foreword This document (EN 4115:2010) has been prepared by the Aerospa

11、ce and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior t

12、o its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2010, and conflicting national standards shall be withdrawn at the latest by October 2010. This document supersed

13、es EN 4115:2001. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national stand

14、ards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, P

15、oland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 4115:2010EN 4115:2010 (E) 4 1 Scope This standard specifies the required characteristics for rubber cushions used on clamps according to EN 3730, EN 4113, EN 4114. For temperature range and environ

16、mental conditions see Table 1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) appl

17、ies. EN 2261, Aerospace series Silicone rubber (VMQ) Hardness 70 IRHD EN 2566, Aerospace series Fluorocarbon rubber (FPM) Hardness 70 IRHD 1)EN 2693, Aerospace series Aluminium alloy AL-P5086- H111 Sheet and strip 0,3 mm a 6 mm EN 3825, Aerospace series Fluorosilicone rubber (FVMQ) Hardness 60 IRHD

18、1)EN 3826, Aerospace series Fluorosilicone rubber (FVMQ) Hardness 70 IRHD 1)EN 9100, Quality Management Systems - Requirements for Aviation, Space and Defense Organizations 1)Published as ASD Prestandard at the date of publication of this standard.BS EN 4115:2010EN 4115:2010 (E) 5 3 Required charact

19、eristics 3.1 Materials According to Table 1. Clamp: according to EN 2693. Cushion: according to this European Standard. Table 1 Materials MateriaL code Elastomer Colour Hardness(IRHD) Temperaturerange 1 Cushion application notes Mass density g/cm S Silicone VMQ EN 2261 rust 70 55 C to 200 C (260 C)

20、Environment of hot air, phosphate ester based fluids or other synthetic fluids and dielectrical use. Not for use with hydrocarbon based fluids. 1,23 F Fluorosilicone FVMQ EN 3826 2 blue 70 55 C to 180 C (200 C) Environment of hot air, hydrocarbon based fluids. Not for use with phosphate ester based

21、fluids except occasional splash. 1,47 V Fluorocarbon FPM EN 2566 3 brown 70 20 C to 200 C (260 C) Fuels, oils and diester lubricants, synthetic fluids, hot air environment and dielectrical use. Not for use with phosphate ester based fluids except occasional splash. 2,05 1Approximate temperature limi

22、ts (in brackets) are for short excursions only. 2Alternative EN 3825. 3Alternative Fluorocarbon rubber (FPM) Hardness 75 IRHD (Class 60C7). BS EN 4115:2010EN 4115:2010 (E) 6 3.2 Configuration Dimensions Masses See Figure 1 and Table 2. Dimensions are in millimetres. All dimensions without tolerances

23、 are maximum values. Cushions without wedge Cushions with wedge (only moulded) possible forms (at manufacturers option) Length l results from the dimensions given in the corresponding dimensional standards of clamps. Cushion profile 1 Valid deviation of form Cushion profile 2 Valid deviation of form

24、 Figure 1 Configuration BS EN 4115:2010EN 4115:2010 (E) 7 Table 2 Dimensions Cushion profile type Metal bandprofilea Size codeab1 b2 Diameter codeae r t1 t2 t3 Q without wedge with wedgemax. min. max. 0,2 0,2 mm21 9,50,8 1N 1K 10,0 4,4 03 to 13 1,0 2,8 4,2 1,2 2,8 42 2 12,70,8 2N 2K 13,2 6,5 03 to 1

25、8 52 12,70,8 2L 18 to 28 5,0 5,0 12,71,0 3N 3L 13 to 28 1,2 4,5 55 12,70,8 4N 4L 28 to 48 1,0 1,5 61 12,71,0 5N 5L 48 to 86 1,2 4,7 62 12,71,5 6N 6L 28 to 86 1,8 5,2 63 aSee the relevant clamp standard. 3.3 Configuration Dimensions Masses The corresponding unit mass of application of cushion is give

26、n by the formula: M = 0,001 Q l + m where m Wedge mass (negligible, about 0,1 g to 0,3 g); l Required cushion length in millimetres; Q Cushion section in square millimetres (see Table 2); Density in gramme per cubic centimeters; M Cushion unit mass in grammes. 4 Designation EXAMPLE Description block

27、 CUSHION, RUBBER Identity block EN4115F2L0025 Number of this standard Code letter for elastomer (see Table 1) Size code (see Table 2) Cushion length in millimeters without cushion length: code letter N NOTE If necessary, the code I9005 shall be placed between the description block and the identity b

28、lock. BS EN 4115:2010EN 4115:2010 (E) 8 5 Marking See the relevant clamp standard. 6 Quality assurance See EN 9100. 7 Technical specification The technical specification concerning the cushioning material to be used is to be agreed between the manufacturer and the user, pending publication of materi

29、al standards. 8 Packaging The cushion rubber shall be packaged so that they are not damaged in transit. The following information shall appear (on a label attached): name and address of manufacturer; description and identity block; number of order; date of delivery. BS EN 4115:2010EN 4115:2010 (E) 9

30、 Bibliography EN 3730, Aerospace series Clamps, saddle fixed and sliding version in aluminium alloy with rubber cushioning Dimension, masses. EN 4113, Aerospace series Clamps, loop (“P“ type) in corrosion resisting steel, passivated with rubber cushioning Dimensions, masses. EN 4114, Aerospace serie

31、s Clamps, loop (“P“ type) in aluminium alloy with rubber cushioning Dimensions, masses. This page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on stan

32、dards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Us

33、ers of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secre

34、tary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standard

35、s.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Se

36、rvices.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of in

37、formation on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8

38、996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information

39、 regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-c

40、ept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in

41、the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: