EN 4180-2001 en Areospace Series - Circular Tubes for Fluids in Titanium and Titanium Alloys - Wide Tolerances - Diameter 4 mm Less Than or Equal to D Less Than or Equal to 40 mm -.pdf

1、BRITISH STANDARD AEROSPACE SERIES Circular tubes, for fluids in titanium and titanium alloys Wide tolerances Diameter 4mmsDs4Omm Dimensions The European Standard EN 4180:2001 has the status of a British Standard ICs 49.025.30; 49.080 BS EN 41 80:2002 Wk present to the responsible European committee

2、any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this committee can be obtained on request to its secretary. Cr oss-r e fer

3、 enc e s The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Ca

4、talogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document c

5、omprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. O BSI 11 January 2002 ISBN O 580 38842 5 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE

6、NORM EN 4180 December 2001 ICs 49.080 English version Aerospace series - Circular tubes, for fluids in titanium and titanium alloys - Wide tolerances - Diameter 4 mm I D I 40 mm - Dimensions Srie arospatiale - Tubes circulaires, pour canalisations en titane et alliages de titane -Tolrances larges -

7、Diamtres 4 mm s D s 40 mm - Dimensions Luft- und Raumfahrt - Runde Leitungsrohre aus Titan und Titanlegierungen - Weite Toleranzen - Durchmesser 4 mm D40mm-Mae This European Standard was approved by CEN on 2 May 2001 CEN members are bound to comply with the CENKENELEC Internal Regulations which stip

8、ulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exi

9、sts in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodi

10、es of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FR NORMUNG COMIT EUROPEN DE NORMALISATION M

11、anagement Centre: rue de Stassart, 36 B-1050 Brussels O 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4180:2001 E EN 4180:2001 (E) Foreword This European Standard has been prepared by the European Association of Aerospace Ma

12、nufacturers (AECMA) . After inquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shal

13、l be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2002, and conflicting national standards shall be withdrawn at the latest by June 2002. According to the CENKENELEC Internal Regulations, the national standards organizat

14、ions of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 2 EN 4180:2001 (E) O Intr

15、oduction This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. 1 Scope This standard specifies the dimensions and tolerances of: Circular tubes, for fluids in titanium and titanium alloys Wid

16、e tolerances Diameter 4 mm D 40 mm for aerospace applications. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed herea

17、fter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. IS0 2964 Aerospace - Tubing - Outsid

18、e diameters and thicknesses - Metric dimensions EN 3848 Aerospace series - Semi-finished metallic products - Method of measuring form deviations EN 4258 Aerospace series - Metallic materials - General organization of standardization - Links between types of EN standards and their use 3 Form See figu

19、re 1. Figure 1 3 EN 4180:2001 (E) Nominal D 4 Recommended dimensions and mass Linear mass a in kg/m for nominal a in mm: 4.1 Diameter, thickness and mass See table 1. Table 1 I 0,4 mm I 0,6 I 0,7 0,8 I 0,9 I 1 I 1,l 03 0,025 I 4 I 0,020 0,029 10,033* 0,036 I - I - I - I 6 I 0,032 0,039 0,046 10,052

20、0,059 I - I - I - I 8 I 0,043 0,053 0,063 10,072* 0,081 10,090 I 0,099 10,107* 0,104 0,116 0,127 0,138* 0,127 0,141 0,156 0,170* 0,067 0,081 0,149 0,167* 0,184 0,201* 0,172 0,192 0,212 0,232* 0,095 - 0,148 0,171* I 0,195 0,218 0,240 0,263* 0,217 0,243* 0,269 0,294 25 I- 0,274 10,307* I 0,339 10,372*

21、 continued Table 1 (concluded) Nominal ID Linear mass a in kg/m for nominal a in mm: I 0,223 I I 14 0,217 10,233* I 0,249 0,265 0,280 I 0,295* I I 16 0,251 10,270 I 0,289 0,307 0,326 I 0,344* 0,361 10,379* I - I I 18 0,285 10,307* I 0,329 0,350 0,371 I 0,392* 0,412 10,432* I 0,452 I 0,416 0,440* + 0

22、,529 0,560* 0,392 0,498 0,467 0,650 I 0688t028 0,869 0,920* 0,647 0,816 For information, calculated with a density of 43 kg/dm3 D/a combinations not referenced in IS0 2964 I 4 EN 4180:2001 (E) Diameter 4 D 18 18 D 30 30 D 40 4.2 Length The order shall specify if tubes are to be supplied in fixed or

23、in random lengths. In the event of a supply of random lengths the minimum and maximum values for the lengths shall be specified on the order. Tolerances f 0,06 f 0,08 f 0,lO 5 Tolerances Length 5.1 Dimensional tolerances 5.1 .I Diameter See table 2. Tolerances Table 2 5.1.2 Thickness See table 3. Ta

24、ble 3 Dimensions in millimetres Thickness Tolerances f 0,lO f 0,05 5.1.3 Length See table 4, only applicable to tubes supplied in fixed lengths. Table 4 Dimensions in millimetres I O I !IO00 5 EN 4180:2001 (E) 5.2 Geometric tolerances 5.2.1 Straightness 5.2.1.1 See EN 3848. Method of measurement and

25、 symbols 5.2.1.2 Tolerances See table 5. Table 5 Dimensions in millimetres I I Straightness deviation Y, per metre I Diameter I 4D40 I 3 I 5.2.2 Roundness 5.2.2.1 See EN 3848. Method of measurement and symbol 5.2.2.2 Tolerances Roundness deviation shall be contained within the outside diameter toler

26、ances. 5.2.3 Eccentricity 5.2.3.1 See EN 3848. Method of measurement and symbol 5.2.3.2 Tolerances Eccentricity shall be contained within the thickness tolerances. 6 BS EN 4180:2002 BSI 389 Chiswick High Road Lon don w4 4AL BSI is the independent national body responsible for preparing British Stand

27、ards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Re vi si ons British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the co

28、nstant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover.

29、Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be add

30、ressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: orders&-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been publishe

31、d as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available whic

32、h give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 71 11. Fax: +44 (0)20 8996 7048. Email: infomi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For d

33、etails ofthese and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 700 1. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is avail

34、able on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, ofthe publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced

35、, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise -without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, ofnecessary details such as symbols, and size, typ

36、e or grade designations. Ifthese details are to be used for any other purpose than implementation then the prior written permission ofBSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyright&-.