EN 4302-2008 en Aerospace series - Open ring insert tool square drive《航空航天系列 方形驱动开环插入工具》.pdf

1、BRITISH STANDARDBS EN 4302:2008Aerospace series Open ring insert tool, square driveICS 49.030.99g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS E

2、N 4302:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2008 BSI 2008ISBN 978 0 580 57073 5National forewordThis British Standard is the UK implementation of EN 4302:2008.The UK participation in its preparation was entrusted to Te

3、chnical Committee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct applica

4、tion.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 4302March 2008ICS 49.030.99English VersionAerospace series - Open ring insert tool, square driveSrie aros

5、patiale - Embouts cannels, tuyauter, carrconducteur axialLuft- und Raumfahrt - Ringeinsteckwerkzeug, offen,verzahntThis European Standard was approved by CEN on 26 August 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Eur

6、opeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English

7、, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cypr

8、us, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT

9、EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 4302:2008: E2 Contents Page Foreword3 1 Scope 4 2 Normative references

10、4 3 Required characteristics.4 3.1 Configuration - Dimensions - Tolerances .4 3.2 Material .4 3.3 Hardness.4 3.4 Surface treatment 4 4 Designation 7 5 Marking .7 6 Technical specification .7 BS EN 4302:20083 Foreword This document (EN 4302:2008) has been prepared by the Aerospace and Defence Industr

11、ies Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to

12、CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2008, and conflicting national standards shall be withdrawn at the latest by September 2008. Attention is drawn to the possibility th

13、at some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound t

14、o implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switz

15、erland and the United Kingdom. BS EN 4302:20084 1 Scope This standard specifies the characteristics of open ring insert tools for splined nuts, metric for aerospace applications. 2 Normative references The following referenced documents are indispensable for the application of this document. For dat

16、ed references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 4156 (all parts), Straigth cylindrical involute splines Metric module, side fit. EN 2424, Aerospace series Marking of aerospace products. EN 41

17、11, Aerospace series Wrenches, splined, sockets for pipe fittings Technical specification. 3 Required characteristics 3.1 Configuration - Dimensions - Tolerances See Figures 1 and 2 and Tables 1 and 2. Dimensions and tolerances are in millimetres. 3.2 Material Material shall be corrosion resistant.

18、The actual material specification shall be the choice of the manufacturer, provided that the spanner meets the requirements of the technical specification, EN 4111. 3.3 Hardness 42 HRC 54 3.4 Surface treatment Nickel-chromium coating Nickel thickness: 5 m Chromium thickness: 0,25 m BS EN 4302:20085

19、Section AB Key 1 Rad. (2 positions) 2 Centre of origin of spline drive. For spline dimensions, see Table 2. 3 Marking 4 Retaining method at manufacturers option Drawing not to scale Dimensions not quoted are at manufacturers discretion. Dimension “A“ to be equidistant about slot centre line. Surface

20、 texture to be unless otherwise specified. Figure 1 Ra3,2 BS EN 4302:20086 Table 1 DN aA B C D E F G H1H2J K L min. max. 0,3 max. 0,01 0,2 0,01 0,2 max. max. max. max. min. h13 04 6,5 22 06 8,5 27 2 08 10,5 31 10 13 33 17,5 12 15 35 19 13 16 36 8 14 17,5 37 20 16 19,5 39 22 9 18 21,5 44 3 25 20 23,5

21、 50 5 30 22 25,5 55,5 6 33 9 12 16 14 22 11,5 4 25 28,5 63 8 35 40 32 35,5 70 9 38 14 18 25 18 10 45 15 5 aDN: Diameter Nominal (outside diameter of the corresponding pipe). Key 1 Circular space width EVEFigure 2 BS EN 4302:20087 Table 2 Splines - 45 pressure angle - side fit - fillet root - 6H tole

22、rance to ISO 4156 Circular space width m Db D Dei DFI Dii Dii Pb E EV radiusDN a Z No. teeth H10 H11 max. min. max. min. min. 04 18 9,5459 13,500 14,52 14,25 12,92 1,253 1,206 1,22506 24 12,7279 18,000 19,02 18,75 17,42 1,256 1,208 08 27 14,3189 20,250 21,28 21,00 19,66 1,257 10 30 15,9099 22,500 23

23、,53 23,25 21,91 1,258 1,209 1,22612 32 16,9706 24,000 25,03 24,75 23,41 1,210 13 34 18,0312 25,500 26,53 26,25 24,91 1,259 14 35 18,5616 26,250 27,28 27,00 25,66 1,260 1,22716 38 0,75 20,1525 28,500 29,53 29,25 27,91 1,66611,261 1,211 1,2281,178 0,19 18 32 22,6274 32,000 33,34 33,00 31,22 1,660 1,60

24、6 20 35 24,7487 35,000 36,34 36,00 34,21 1,661 22 38 26,8701 38,000 39,35 39,00 37,21 1,662 1,607 1,62525 41 1 28,9914 41,000 42,35 42,00 40,212,22141,663 1,608 1,6261,571 0,25 32 37 1,25 45 32,7037 46,2500 47,91 47,50 45,27 2,7768 2,062 2,003 2,023 1,963 0,31 aDN: Diameter Nominal (outside diameter

25、 of the corresponding pipe). Note Missing dimensions in Figure 2, see ISO 4156. 4 Designation EXAMPLE Description block WRENCH Identity block EN430210 Number of this standard DN (tube diameter code, see Tables 1 and 2) NOTE If necessary the code I9005 shall be placed between the description block an

26、d the identity block. 5 Marking EN 2424, style C, as indicated on Figure 1. 6 Technical specification EN 4111 BS EN 4302:2008BS EN 4302:2008BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It prese

27、nts the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to

28、 improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996

29、9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Serv

30、ices. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards

31、, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all it

32、s products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other

33、 benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/w

34、ww.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or t

35、ransmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.