EN 4531-003-2012 en Aerospace series - Connectors optical circular single and multipin coupled by triple start threaded ring - Flush contacts - Part 003 Square flange receptacle - .pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 4531-003:2012Aerospace series Connectors, optical, circular,single and multipin, coupledby triple start threaded ring Flush contactsPart 003: Square flange receptacle Produ

2、ct standardBS EN 4531-003:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 4531-003:2012.It supersedes BS EN 4531-003:2007 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/6, Aerospace avionic electrical and

3、fibre optictechnology.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2012. Pub

4、lished by BSI StandardsLimited 2012ISBN 978 0 580 75696 2ICS 49.060Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 May 2012.Amendments issued since publicationD

5、ate Text affectedBS EN 4531-003:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4531-003 May 2012 ICS 49.060 Supersedes EN 4531-003:2007English Version Aerospace series - Connectors, optical, circular, single and multipin, coupled by triple start threaded ring - Flush contacts - Part 003: S

6、quare flange receptacle - Product standard Srie arospatiale - Connecteurs optiques circulaires accouplement par bague filete trois filets - Contacts affleurants - Partie 003: Embase fixation par collerette carre - Norme de produit Luft- und Raumfahrt - Optische Rundsteckverbinder mit dreigngiger Sch

7、raubkupplung - Bndige Kontakte - Teil 003: Fester Steckverbinder mit quadratischem Montageflansch - Produktnorm This European Standard was approved by CEN on 10 September 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Eu

8、ropean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versi

9、ons (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria,

10、Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. E

11、UROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4531-003:2012: EBS EN 453

12、1-003:2012EN 4531-003:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Required characteristics .45 Designation 56 Marking .57 Technical specification .5BS EN 4531-003:2012EN 4531-003:2012 (E) 3 Foreword This document (EN 4531-003:2012) has been prepare

13、d by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries

14、 of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2012, and conflicting national standards shall be withdrawn at the latest by November 2012. Atte

15、ntion is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 4531-003:2007. According to the CEN/CENELEC Internal Regulatio

16、ns, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

17、Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 4531-003:2012EN 4531-003:2012 (E) 4 1 Scope This European Standard specifies the characteristics of mounted square flange receptacles in the family of circular connect

18、ors with triple start threaded coupling. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the

19、 referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products EN 3645-003, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 003: Receptacle square fl

20、ange mounting Product standard EN 4531-001, Aerospace series Connectors, optical, circular, single and multipin, coupled by triple start threaded ring Flush contacts Part 001: Technical specification EN 4531-002, Aerospace series Connectors, optical, circular, single and multipin, coupled by triple

21、start threaded ring Flush contacts Part 002: Specification of performance and contact arrangements 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 4531-001 apply. 4 Required characteristics 4.1 Dimensions and masses See EN 3645-003 for dimensions and

22、Table 1 for masses. Table 1 Shell size Mass g Classes F, W, N and Z K and S J, M and X 9 10 25 1011 16 35 13 13 22 45 1915 31 59 27 19 57 98 4521 65 110 51 25 97 148 90BS EN 4531-003:2012EN 4531-003:2012 (E) 5 4.2 Material and surface treatment See EN 4531-002. 4.3 Panel cut-out See EN 3645-003. 4.4

23、 Optical, mechanical and climatic characteristics See EN 4531-002. 5 Designation EXAMPLE Description block CONNECTOR, OPTICAL Identification block EN4531-0XXXXXX Number of the basic standard Square flange receptacle Shell size code (see EN 4531-002) Arrangement code (see EN 4531-002) Sleeve code (se

24、e EN 4531-002) Environmental class (see EN 4531-002) Polarization (see EN 4531-002) 6 Marking The marking shall include the identification defined in Clause 5, the date of manufacture (year, week) and the name or trade mark of the manufacturer or conform to standard EN 2424, code P, if required. 7 T

25、echnical specification See EN 4531-001. This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europ

26、e and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (

27、0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone

28、finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI

29、 offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standard

30、s directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will s

31、upply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 700

32、5Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regard

33、ing online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyr

34、ighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may

35、 be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: