EN 4550-1-2014 en Aerospace series - Pipe coupling 37 Design configuration - Inch series - Part 1 Male sealing ends spherical《航空航天系列 管接头 37 设计组态 寸系列 第1部分 男封端 球形》.pdf

1、BSI Standards PublicationBS EN 4550-1:2014Aerospace series Pipecoupling, 37 Designconfiguration Inch seriesPart 1: Male sealing ends, sphericalBS EN 4550-1:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 4550-1:2014. Itsupersedes BS EN 4550-1:2003 which is

2、withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/69, Aerospace hydraulic systems, fluids andcomponents.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necess

3、aryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 87290 7ICS 49.080Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was publi

4、shed under the authority of theStandards Policy and Strategy Committee on 31 December 2014.Amendments issued since publicationDate Text affectedBS EN 4550-1:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4550-1 December 2014 ICS 49.080 Supersedes EN 4550-1:2003English Version Aerospace ser

5、ies - Pipe coupling, 37 - Design configuration - Inch series - Part 1: Male sealing ends, spherical Srie arospatiale - Systme de raccordement 37 - Configuration gomtrique - Srie inch - Partie 1: Extrmit dtanchit mles, sphriques Luft- und Raumfahrt - Rohrverschraubungen 37 - Konstruktionsblatt - Inch

6、-Reihe - Teil 1: Steckdichtungsenden mit Kugelbuchsen This European Standard was approved by CEN on 11 November 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without a

7、ny alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other langu

8、age made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark

9、, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FO

10、R STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4550-1:2014 EBS EN 4550-1:2014EN

11、4550-1:2014 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Dimensions Tolerances .4 4 Designation 5 Annex A (informative) Standard evolution form .6 BS EN 4550-1:2014EN 4550-1:2014 (E) 3 Foreword This document (EN 4550-1:2014) has been prepared by the Aerospace and Defence Indus

12、tries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation t

13、o CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2015, and conflicting national standards shall be withdrawn at the latest by June 2015. Attention is drawn to the possibility that some

14、of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 4550-1:2003. According to the CEN-CENELEC Internal Regulations, the national standards organizations of th

15、e following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherl

16、ands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 4550-1:2014EN 4550-1:2014 (E) 4 1 Scope This European Standard defines the dimensions and tolerances for the male sealing end of inch series pipe couplings, 37, spherical, fo

17、r aerospace applications. Matched fluid system component shall have a female sealing end in accordance with EN 4550-4. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, onl

18、y the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 4550-4, Aerospace series Pipe coupling, 37 Design configuration Inch series Part 4: Female sealing ends ISO 3161, Aerospace UNJ threads General requirements and l

19、imit dimensions 3 Dimensions Tolerances See Figure 1 and Table 1. Dimensions and tolerances are in millimetres. Key 1 Thread NOTE All outer surfaces shall be concentric with a tolerance of diameter 0,1 mm relative to the inner diameter A. Figure 1 BS EN 4550-1:2014EN 4550-1:2014 (E) 5 Table 1 Dimens

20、ional code a Nominal diameter Thread b A B C D E F G H J K L R S + 0,35 0, 0,10 0,10 0, 0,1 0,50 0,10 0,25 0,13 03 04,763 .375 0-24UNJF-3A 02,65 02,90 4,4 07,00 03,30 04,53 07,90 0,5 1,3 4,06 12,20 5,50 1,80 07,90 0,74 04 06,350 .437 5-20UNJF-3A 04,25 04,50 4,8 09,00 04,80 06,25 09,25 3,20 14,00 5,5

21、5 2,00 0,80 05 07,924 .500 0-20UNJF-3A 05,80 06,10 10,50 06,50 07,77 10,80 2,45 5,50 0,74 06 09,525 .562 5-18UNJF-3A 07,35 07,70 4,9 11,90 08,10 09,61 12,20 1,50 5,65 2,30 0,87 08 12,700 .750 0-16UNJF-3A 09,75 10,10 6,3 16,50 10,80 12,66 16,75 0,8 1,8 3,30 16,50 8,35 2,55 12,05 1,10 10 15,875 .875 0

22、-14UNJF-3A 12,15 12,50 6,6 19,30 13,70 15,50 19,65 1,88 19,00 8,30 3,05 1,05 12 19,050 1.062 5-12UNJ-3A 15,30 15,70 7,8 23,60 16,90 19,34 24,00 3,15 21,80 11,10 3,30 16,05 1,43 16 25,400 1.312 5-12UNJ-3A 21,20 21,70 30,00 23,25 25,64 30,35 0,00 22,90 1,42 aThis two digit quantitative code correspond

23、s to the tube nominal diameter as the number of 1/16 inch increments it contains i.e. divided by 1/16 (.0625) inch. bQuoted in inches in accordance with ISO 3161. 4 Designation EXAMPLE Identity block EN4550-1-08 Number of this standard Dimensional code (see Table 1) BS EN 4550-1:2014EN 4550-1:2014 (

24、E) 6 Annex A (informative) Standard evolution form MODIFICATION REASON AND VALIDATION Figure 1 Before: dimension L (groove width) was represented up to top of thread. After: dimension L (groove width) is represented up to the bottom of thread. Wrong representation of dimension L (groove width). Acco

25、rdance with standard DT45-02. Figure 1 Before: Dimension R was indicated as an absolute dimension (boxed dimension). After: Dimension R is indicated as a dimension with tolerance and tolerance 0,13 is added in Table 1. Incompatibility with another absolute dimension. Accordance with standard DT45-02

26、. Figure 1 Before: Dimension K was indicated as an absolute dimension (boxed dimension). After: Dimension K is indicated as a dimension with tolerance and tolerance 0,10 is added in Table 1. Incompatibility with another absolute dimension. Accordance with standard DT45-02. This page deliberately lef

27、t blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Instituti

28、on (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully

29、assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more

30、 about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies c

31、an also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further informatio

32、n on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards dev

33、elopments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards w

34、hen theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With update

35、s supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business.

36、 If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or en

37、tity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a re

38、trieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW