EN 4644-003-2016 en Aerospace series - Connector electrical and optical rectangular modular rectangular inserts operating temperature 175 (or 125 continuous - Part 003 Rectangular .pdf

1、BSI Standards PublicationBS EN 4644-003:2016Aerospace series Connector,electrical and optical,rectangular, modular,rectangular inserts, operatingtemperature 175 C (or 125 C)continuousPart 003: Rectangular inserts ProductstandardBS EN 4644-003:2016 BRITISH STANDARDNational forewordThis British Standa

2、rd is the UK implementation of EN 4644-003:2016.It supersedes BS EN 4644-003:2011 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/6, Aerospace avionic electrical and fibre optictechnology.A list of organizations represented on this committee can beo

3、btained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016. Published by BSI StandardsLimited 2016ISBN 978 0 580 90783 8ICS 49.060; 49.090Complian

4、ce with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 April 2016.Amendments issued since publicationDate Text affectedBS EN 4644-003:2016EUROPEAN STANDARD NORME EUROPENNE EUR

5、OPISCHE NORM EN 4644-003 April 2016 ICS 49.060; 49.090 Supersedes EN 4644-003:2011English Version Aerospace series - Connector, electrical and optical, rectangular, modular, rectangular inserts, operating temperature 175 C (or 125 C) continuous - Part 003: Rectangular inserts - Product standard Srie

6、 arospatiale - Connecteur, lectrique et optique, rectangulaire, modulaire, inserts rectangulaires, temprature de fonctionnement 175 C (ou 125 C) continu - Partie 003 : Inserts rectangulaires - Norme de produit Luft- und Raumfahrt - Elektrische und optische Rechtecksteckverbinder, modular, rechteckig

7、e Kontakteinstze, Dauerbetriebstemperatur 175 C (oder 125 C) konstant - Teil 003: Rechteckige Kontakteinstze - Produktnorm This European Standard was approved by CEN on 27 September 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giv

8、ing this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three off

9、icial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies o

10、f Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,

11、 Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide fo

12、r CEN national Members. Ref. No. EN 4644-003:2016 EBS EN 4644-003:2016EN 4644-003:2016 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Terms, definitions and abbreviations . 5 4 Requirements . 6 5 Designation 8 6 Marking . 8 7 Technical specification 8 B

13、S EN 4644-003:2016EN 4644-003:2016 (E) 3 European foreword This document (EN 4644-003:2016) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Stand

14、ard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest

15、by October 2016, and conflicting national standards shall be withdrawn at the latest by October 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such

16、 patent rights. This document supersedes EN 4644-003:2011. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

17、Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 4644-003:2016EN 4644-0

18、03:2016 (E) 4 Introduction The rectangular inserts defined by this European Standard are to be used in connectors defined by EN 4644-001. BS EN 4644-003:2016EN 4644-003:2016 (E) 5 1 Scope This European Standard specifies the characteristics of rectangular inserts used in the family of electrical and

19、 optical, rectangular, modular, rectangular inserts, operating temperature 175 C (or 125 C) continuous, coupled by a locking mechanism or rack and panel. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its app

20、lication. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 4644-001, Aerospace series Connector, electrical and optical, rectangular, modular, rectangular inserts, operating temperature

21、175 C (or 125 C) continuous Part 001: Technical specification EN 4644-002, Aerospace series Connector, electrical and optical, rectangular, modular, rectangular inserts, operating temperature 175 C (or 125 C) continuous Part 002: Specification of performance and contact arrangements 3 Terms, definit

22、ions and abbreviations For the purposes of this document, the terms, definitions and abbreviations given in EN 4644-001 apply. BS EN 4644-003:2016EN 4644-003:2016 (E) 6 4 Requirements 4.1 Dimensions and mass See Figure 1, Table 1 and Table 2. or Key 1 Insert retention clip butting position 2 Front i

23、nsert bottoming in the shell 3 Interfacial seal (on insert for pin contacts only) 4 Rear grommet 5 Dimension on ribs 6 For B keying 7 For A keying 8 Marking area Figure 1 BS EN 4644-003:2016EN 4644-003:2016 (E) 7 Table 1 Dimensions in millimetres Insert for female contacts Insert for male contacts A

24、 9,41 9,28 1,61 1,48 B 12,38 12,25 4,58 4,45 C Insert without size 8 contact cavity 28,80 28,10 21,00 20,30 Insert with size 8 contact cavity 29,80 29,10 21,00 20,30 D Insert without size 8 contact cavity 20,05 19,84 12,25 12,04 Insert with size 8 contact cavity 21,05 20,84 12,25 12,04 Table 2 Maxim

25、um masses Environmental insert Semi environmental insert Non environmental insert Non environmental insert (with grommet) g g g g Insert for pin contacts 10 9 8 9 Insert for socket contacts 12 11 10 Not applicable BS EN 4644-003:2016EN 4644-003:2016 (E) 8 5 Designation EXAMPLE Description block INSE

26、RT Identity block EN4644-00306MAEG Standard number Contact arrangement name (see EN 4644-002) Contact type M: male contact. F: female contact. Insert polarization Class E: Environmental: insert with rear grommet for male and socket insert and with interfacial seal for male insert. N: Non environment

27、al: insert without interfacial seal and without rear grommet. T: Semi environmental: male insert with interfacial seal, without grommet. H: Non environmental: male insert with grommet, without interfacial seal. Grounding G: coaxial, triaxial and quadrax contacts, grounded cavities. A: coaxial, triax

28、ial and quadrax contacts, non grounded cavities. 6 Marking Insert identification marking, as specified in Clause 5, shall be applied in the position shown on Figure 1. In addition, marking shall show: Date code of manufacture (year week); Manufacturer name or trademark. 7 Technical specification See

29、 EN 4644-001. This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Stand

30、ards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embod

31、ied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your orga

32、nization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, thr

33、ough our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standard

34、s easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date.

35、You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive

36、the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few o

37、r as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our product

38、s and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and

39、copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no e

40、xtract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW