EN 4652-211-2015 en Aerospace series - Connectors coaxial radio frequency - Part 211 Type 2 TNC interface - Clamp nut assembly version - Right angle plug - Product standard《航空航天系列 .pdf

1、BSI Standards PublicationBS EN 4652-211:2015Aerospace series Connectors, coaxial, radio frequencyPart 211: Type 2, TNC interface Clamp nut assembly version Right angle plug Product standardBS EN 4652-211:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 4652-

2、211:2015.The UK participation in its preparation was entrusted to Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the

3、necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015ISBN 978 0 580 88571 6 ICS 49.060 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standa

4、rd was published under the authority of the Standards Policy and Strategy Committee on 30 September 2015.Amendments/corrigenda issued since publicationDate Text affectedBS EN 4652-211:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORMEN 4652-211 September 2015 ICS 49.060 English Version Aerospace

5、 series - Connectors, coaxial, radio frequency - Part 211: Type 2, TNC interface - Clamp nut assembly version - Right angle plug - Product standard Srie arospatiale - Connecteurs coaxiaux pour radio frquences - Partie 211 : Type 2, interface TNC - Version presse toupe - Fiche coude - Norme de produi

6、t Luft- und Raumfahrt - Koaxiale Hochfrequenz-Steckverbinder - Teil 211: Typ 2 TNC-Schnittstelle - Klemmkonus - Freier Steckverbinder, 90 abgewinkelt - Produktnorm This European Standard was approved by CEN on 14 February 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulation

7、s which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. Th

8、is European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN mem

9、bers are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portu

10、gal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any for

11、m and by any means reserved worldwide for CEN national Members. Ref. No. EN 4652-211:2015 EBS EN 4652-211:2015EN 4652-211:2015 (E) 2 Contents Page European foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Required characteristics 4 5 Test methods 8 6 Qualification . 11 7 Q

12、uality assurance . 11 8 Designation . 11 9 Marking 11 10 Packaging . 11 11 Storage 11 BS EN 4652-211:2015EN 4652-211:2015 (E) 3 European foreword This document (EN 4652-211:2015) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enqui

13、ries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national

14、 standard, either by publication of an identical text or by endorsement, at the latest by March 2016, and conflicting national standards shall be withdrawn at the latest by March 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent right

15、s. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cy

16、prus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the Unit

17、ed Kingdom. BS EN 4652-211:2015EN 4652-211:2015 (E) 4 1 Scope This European Standard specifies the characteristics of screwed on coupling (TNC interface) coaxial right angle plugs 50 ohms. The cable to connector assembly is a clamp technology. 2 Normative references The following documents, in whole

18、 or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591 1), Aerospace series Elements of

19、 electrical and optical connection Test methods EN 2812, Aerospace series Stripping of electric cables EN 4652-001, Aerospace series Connectors, coaxial, radio frequency Part 001: Technical specification EN 4652-212, Aerospace series Connectors, coaxial, radio frequency Part 212: Type 2, TNC interfa

20、ce Clamp nut assembly version Square flange receptacle Product standard EN 4652-213, Aerospace series Connectors, coaxial, radio frequency Part 213: Type 2, TNC interface Clamp nut assembly version Bulkhead receptacle Product standard2)EN 9133, Aerospace series Quality management systems Qualificati

21、on procedure for aerospace standard parts TR 6058, Aerospace series Cable code identification list 3)3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 4652-001 apply. 4 Required characteristics The connection technology shall comply to required tests de

22、scribed in Clause 5. Interface shall comply to EN 4652-001. A self-locking device on plugs shall be proposed if hole for lockwire does not exist. Water ingress resistance is required in mated conditions for all cable groups. Water ingress resistance is required in unmated condition for cable group A

23、. 1) All parts quoted in this European Standard. 2) Published as ASD-STAN Prestandard at the date of publication of this European Standard. http:/www.asd-stan.org/ 3) Published as ASD-STAN Technical Report at the date of publication of this European Standard. http:/www.asd-stan.org/ BS EN 4652-211:2

24、015EN 4652-211:2015 (E) 5 4.1 Configuration, dimension and mass Mass without heat shrink tubing. See Figure 1 and Table 1. Dimensions in millimetres Key 1 3 holes for lockwire 1 2 Marking 3 HEX. 14 4 Flat 10 5 HEX. F Figure 1 TNC right angle plug Marking: see Clause 9. BS EN 4652-211:2015EN 4652-211

25、:2015 (E) 6 Table 1 TNC right angle plug dimensions and mass Cable group B C D E HEX. F Interface style Mass (cable jacket) (cable conductor) (according to EN 4652-001) g max. max. max. max. A 43,0 7,8 2,3 15 12 Style C 46,9 B 33,8 5,55 1,4 13 8 Style C 35,2 4.2 Materials and finish Centre contact :

26、 Copper alloy gold plated over nickel undercoat Insulators . : PTFE Seals . : Silicone rubber or silicone fluoride Body . : Copper alloy, nickel plated Heat shrink tube . : Polyolefin Coupling nut, rear screw and other parts materials shall have mechanical and electrical characteristics consistent w

27、ith the requirements of this product standard. 4.3 Temperature Operating temperature shall be between 65 C and 165 C. 4.4 Electrical characteristics Maximum operating frequency : 6 GHz VSWR . : 1,15 max. from DC to 3 GHz 1,20 max. from 3 GHz to 6 GHz Impedance . : 50 Insertion loss : 0,07f dB max.,

28、f in GHz Contact resistance (initial centre contact) . : 2,0 m max. Insulation resistance . : 5 000 M min. Withstand voltage : 1 500 Veff (at sea level) 4.5 General characteristics Tightening torque of coupling nut . : 2,6 Nm 0,3 Nm Force to engage or disengage : 0,23 Nm max. Service life . : 500 cy

29、cles Retention of centre contact : 27 N min. Retention of cable . : see Table 2. BS EN 4652-211:2015EN 4652-211:2015 (E) 7 Table 2 Retention of cable Cable group Retention of cable N min. A 180 B 180 4.6 Admissible cables, tools and stripping lengths See Table 3 to Table 5. Table 3 Stripping lengths

30、 Cable group Cable code (see TR 6058) Stripping lengths mm A KW B KX Table 4 Stripping lengths cable group A A B min. mm max. mm min. mm max. mm 4,6 5,4 8,6 9,4 Table 5 Stripping lengths cable group B A B min. mm max. mm min. mm max. mm 3,6 4,4 7,6 8,4 For stripping see EN 2812. BS EN 4652-211:2015E

31、N 4652-211:2015 (E) 8 5 Test methods See Table 6. Table 6 Test methods EN 2591- Designation of the test Details 101 Visual examination Applicable 102 Examination of dimensions and mass TNC interface Style A: see 4.1 and EN 4652-001. TNC interface Style B: see 4.1 and EN 4 652-001. TNC interface Styl

32、e C: see 4.1 and EN 4 652-001. The manufacturer shall precise which style of interface is used. 201 Contact resistance - low level Applicable on centre contact 202 Contact resistance at rated current 2,0 m max. = initial centre contact and 2,5 m max. after test For nickel plated connectors: 0,4 m ma

33、x. = initial external contact and2,0 m max. after test 204 Discontinuity of contacts in the microsecond range Duration of micro discontinuity: 1sMethod B Test time: throughout duration of tests EN 2591-402 and EN 2591-403. 206 Measurement of insulation resistance 5 000 M min. 207 Voltage proof test

34、Method A Pressure Mated aUnmated aSea level 1 500 1 500 12,1 kPa 800 5504,7 kPa 375 3502,7 kPa 250 200aValues in Volts RMS. 212 Surface transfer impedance Applicable (up to 100 MHz) 3 m 1 MHz1 m 10 MHz 3 m 30 MHz5 m 100 MHz 214 Lightning strike, current and voltage pulse 10 kA wave form 5 A, 10 A RM

35、S BS EN 4652-211:2015EN 4652-211:2015 (E) 9 EN 2591- Designation of the test Details 221 Voltage Standing Wave Ratio (VSWR) Method B VSWR 1,15 from DC to 3 GHz VSWR 1,20 from 3 GHz to 6 GHz. 222 Insertion Loss (I.L.) 0,07f dB max., f in GHzMeasurement shall be performed with connector mated with EN

36、4652-212 or EN 4652-213 receptacle from same technology and cable group 223 Measurement of characteristic impedance of a coaxial connector or contact 50 5 at 200 MHz Input impedance 224 RF leakage Measured from 2 GHz to 3 GHz 50 dB for connectors on cable group A 60 dB for connectors on cable group

37、B 225 RF high potential withstanding voltage 1 000 V at 5 MHz 226 Corona level Corona extinction voltage 315 V rms at 4,4 kPa (70000 feet altitude) 303 Cold/low pressure and damp heat Five (5) cycles Minimum temperature 60 C 305 Rapid change of temperature Mated connectors TA= +05165 C; TB= 5065 C.

38、307 Salt mist The connectors shall be suspended in the test chamber with non-metallic cords, so that no accumulation of condensed saline solution can occur. The connectors shall be: subjected to 50 cycles of mating and unmating at a rate 5 cycles/min.; exposed to the salt mist: mated for 240 h not e

39、xposed to the salt mist: unmated for 48 h 308 Sand and dust The mated connectors shall be arranged so that their longitudinal axis is parallel to the wind direction, with the rear of the plug facing the wind. Wind velocity in the duct: (3,5 0,5) m/s Number of cycles: one (1) 311 Low air pressure Ref

40、er to test EN 2591-207. BS EN 4652-211:2015EN 4652-211:2015 (E) 10 EN 2591- Designation of the test Details 314 Immersion at low air pressure Specimen without heat shrinkable tube In unmated condition (applicable only for connectors on cable group A): After the three (3) cycles, remove the specimen

41、from salt water, clean the interface with soft paper. In mated condition (applicable for all connectors): standard procedure.315 Fluid resistance See EN 4652-001. 317 Flammability Method A 402 Shock Method A Half sine Severity 30 g, duration 11 ms Number of shocks: one (1) in each way for each of th

42、e three (3) axis (six (6) shocks in all)403 Sinusoidal and random vibration Method A: sinusoidal vibration with the following individual modalities:Level 2 50 Hz to 70 Hz : 1,5 mm double amplitude 70 Hz to 2 000 Hz : 20 g Three (3) axis or two (2) axis (straight connectors) Duration 4 h per axis at

43、ambient temperature 404 Transverse load Applicable on rear of plug; torque moment = 15 Nm 406 Mechanical endurance 500 cycles408 Mating and unmating forces 0,23 Nm max.409 Contact retention in insert 27 N min., applicable on cabled specimen 417 Tensile strength (crimped connection) See Table 2. 418

44、Gauge insertion/extraction forces (female contacts) Not applicable 422 Locking wire hole strength Applicable 507 Plating porosity Applicable 508 Measurement of thickness of coating on contacts Applicable 509 Adhesion of coating on contacts Applicable 513 Magnetic permeability 2 BS EN 4652-211:2015EN

45、 4652-211:2015 (E) 11 6 Qualification Qualification test programme: see EN 4652-001. 7 Quality assurance See EN 9133. 8 Designation EXAMPLE Description block CONNECTOR, COAXIAL Identity block EN4652-211A50 Number of the basic standard Connector interface type code (see EN 4652-001) 2 = TNC Technolog

46、y of assembly code (see EN 4652-001) 1 = clamp Connector model code (see EN 4652-001) 1 = right angle plug Cable group code (see Table 3) Impedance: 50 = 50 NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 9 Marking See EN 4652-001 10 Packaging

47、See EN 4652-001. 11 Storage See EN 4652-001. This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standar

48、ds and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience a

49、nd expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and ref_ined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about