EN 4702-04-2017 en Aerospace series - Quick release fastening systems for non-structural and lining applications - Part 04 Spring clamp.pdf

1、Aerospace series - Quick release fastening systems for non-structural and lining applicationsPart 04: Spring clampBS EN 470204:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4702-04 October 2017 ICS 49.035 Eng

2、lish Version Aerospace series - Quick release fastening systems for non-structural and lining applications - Part 04: Spring clamp Srie arospatiale - Fixations rapides filetes applications structurales et non structurales et revtements intrieurs - Partie 04: Collier lyre Luft- und Raumfahrt - Schnel

3、lverschlusssysteme fr nicht-strukturelle und Innenausstattungsanwendungen - Teil 04: Feder-ClipThis European Standard was approved by CEN on 23 July 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the st

4、atus of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French,

5、German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cro

6、atia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Tur

7、key and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.

8、Ref. No. EN 4702-04:2017 ENational forewordThis British Standard is the UK implementation of EN 470204:2017.The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obta

9、ined on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 98238 5ICS 49.035Compliance with a

10、 British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 470204:2017EUROPEAN STANDARD

11、 NORME EUROPENNE EUROPISCHE NORM EN 4702-04 October 2017 ICS 49.035 English Version Aerospace series - Quick release fastening systems for non-structural and lining applications - Part 04: Spring clamp Srie arospatiale - Fixations rapides filetes applications structurales et non structurales et revt

12、ements intrieurs - Partie 04: Collier lyre Luft- und Raumfahrt - Schnellverschlusssysteme fr nicht-strukturelle und Innenausstattungsanwendungen - Teil 04: Feder-ClipThis European Standard was approved by CEN on 23 July 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations

13、which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This

14、 European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN membe

15、rs are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portuga

16、l, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in

17、any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4702-04:2017 EBS EN 470204:2017EN 4702-04:2017 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Representations 4 4 Designation 6 5 Marking . 6 6 Quality assurance 6 7 Technical Specifica

18、tion . 7 Bibliography 8 BS EN 470204:2017EN 4702-04:2017 (E) 3 European foreword This document (EN 4702-04:2017) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this As

19、sociation, this European Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or

20、by endorsement, at the latest by April 2018, and conflicting national standards shall be withdrawn at the latest by April 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any

21、or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republi

22、c of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 470204:2017EN 4702-04:2017 (E) 4 1 Scope This

23、standard describes the dimensions, mass, tolerances and static values of quick-release and locking clamps for use in fuselage interior equipment and non-structural or secondary structural area. 2 Normative references The following documents are referred to in the text in such a way that some or all

24、of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series - Marking of aerospace products EN 4710-01, Aerospace

25、series Quick release fastening systems for non-structural applications Part 01: Technical specification EN 10132-4, Cold-rolled narrow steel strip for heat-treatment Technical delivery conditions Part 4: Spring steels and other applications EN 10151, Stainless steel strip for springs Technical deliv

26、ery conditions EN 22768-1:1993, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:1989) EN 22768-2:1993, General tolerances Part 2: Geometrical tolerances for features without individual tolerance indications (ISO 2768-2:1989

27、) EN ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings (ISO 10683:2014) 3 Representations 3.1 Configuration, dimensions, tolerances and mass The configuration, dimensions, tolerances and mass shall confirm with Figure 1 and Table 2. Tolerances not specified, shall be in accordanc

28、e with ISO 2768-mK (EN 22768-1:1993 and EN 22768-2:1993). Missing dimensions are left to manufacturers option. 3.2 Material and surface treatment See Table 3. 3.3 Mechanical characteristics Ultimate loads see Table 1. The applicable temperature range is 55 C to 85 C. Table 1 Loads Type code Ultimate

29、 loads Material code N 01 600 A, C 02 600 A, C BS EN 470204:2017EN 4702-04:2017 (E) 5 Key L1Length 1 L2Length 2 W Thickness K Height T Grip range A Overall length D1Hole length D2Hole width 1 Marking Figure 1 Configuration “spring clamp” Table 2 Dimension and mass Type Code L1L2W A K D1 D2Installati

30、on hole T Mass mm mm mm mm mm mm mm mm null mm mm g 01 9,4 9,4 0,5 12,0 10,9 8,40,37,2 9,4+0,1null 9,4+0,13,6+0,21,1 02 16,00,213,9 0,5 19,1 10,7 13,7 7,7 140,2null 16,2+0,43,5+0,22,2 BS EN 470204:2017EN 4702-04:2017 (E) 6 3.4 Material Table 3 Material Material code Material Surface treatment A Allo

31、y steel 1.1274 according to EN 10132-4 EN ISO 10683 C Stainless steel 1.4310 according to EN 10151 4 Designation EXAMPLE 5 Marking Marking shall be in accordance with EN 2424, Style F. 6 Quality assurance 6.1 Supplier certification The manufacturers operations shall be an approved production organiz

32、ation for aerospace products and shall demonstrate that it has implemented and is able to maintain a quality system (e. g. according to EN 9100 or another in aerospace accepted and established quality management system). 6.2 Product qualification The technical requirements for the product standard q

33、ualification are listed in EN 4710-01. The product qualification shall be performed to the process as defined in e. g. EN 9133 to achieve a qualification approval from the controlling Certification Authority (CA). BS EN 470204:2017EN 4702-04:2017 (E) 7 7 Technical Specification Required tests for ac

34、ceptance and qualification shall be in accordance to Table 4 and EN 4710-01. Table 4 Requirements, inspections and tests Characteristic Requirements Requirements according to EN 4710-01 Inspections and tests according to EN 4710-01 Aa Qb Materials According to Table 3 4.1 5.4.1 X X Dimensions and ma

35、sses According to Table 2 4.2 5.4.2 X X Surface defects According to EN 4710-01 4.3.1 5.4.3.1 X X Surface treatment According to Table 3 4.3.2 5.4.3.2 X X Ultimate tensile loads According to Table 1 4.4.1 5.4.4.1 X Corrosion resistance According to EN 4710-01 4.5 5.4.5 X Functionality According to E

36、N 4710-01 4.7.1 5.4.7.1 X Endurance 1 500 cycles 4.7.2 5.4.7.2 X Identification marking of the product According to EN 4710-01 4.8.1 5.4.8.1 X X Identification marking of the package According to EN 4710-01 4.8.2 5.4.8.2 X X aAcceptance test. bQualification test. BS EN 470204:2017EN 4702-04:2017 (E)

37、 8 Bibliography 1 EN 9100, Quality Management Systems Requirements for Aviation, Space and Defense Organizations 2 EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard parts BS EN 470204:2017This page deliberately left blankBSI is the national body resp

38、onsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together bu

39、siness, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations

40、 of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or

41、Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Develo

42、pment Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the i

43、nternational standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or

44、 publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use

45、 only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standar

46、d purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network,

47、 you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For

48、 further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch

49、 with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the