EN 4807-2017 en Aerospace series - Flange couplings - Weld coupling 90 lbow in heat resisting steel - Inch series.pdf

1、Aerospace series - Flange couplings - Weld coupling, 90 elbow, in heat resisting steel - Inch seriesBS EN 4807:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4807 May 2017 ICS 49.080 English Version Aerospace

2、series - Flange couplings - Weld coupling, 90 elbow, in heat resisting steel - Inch series Srie arospatiale - Raccordement bride - Raccord souder, coude 90, en acier rsistant chaud - Srie en inches Luft- und Raumfahrt - Rohrverschraubung mit Flanschen und Schweistutzen, Winkelstutzen 90, aus hochwar

3、mfestem Stahl - Inch-Reihe This European Standard was approved by CEN on 14 November 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date l

4、ists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation und

5、er the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former

6、Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION C

7、OMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4807:2017 ENational forewordThis British Standard is

8、 the UK implementation of EN 4807:2017.The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to

9、 include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 95338 5ICS 49.080Compliance with a British Standard cannot confer immunity from legal obligations. This

10、 British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2017.Amendments/corrigenda issued since publicationDate Text affected BRITISH STANDARDBS EN 4807:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 4807 May 2017 ICS 49.080 English Ver

11、sion Aerospace series - Flange couplings - Weld coupling, 90 elbow, in heat resisting steel - Inch series Srie arospatiale - Raccordement bride - Raccord souder, coude 90, en acier rsistant chaud - Srie en inches Luft- und Raumfahrt - Rohrverschraubung mit Flanschen und Schweistutzen, Winkelstutzen

12、90, aus hochwarmfestem Stahl - Inch-Reihe This European Standard was approved by CEN on 14 November 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteratio

13、n. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by

14、translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, F

15、inland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR ST

16、ANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4807:2017 EBS EN 4807:2017EN 4807:201

17、7 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Required characteristics . 4 4 Designation . 7 5 Identification marking . 7 6 Technical specification . 7 7 Quality Assurance. 7 BS EN 4807:2017EN 4807:2017 (E) 3 European foreword This document (EN 4807:2017) has b

18、een prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the membe

19、r countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2017, and conflicting national standards shall be withdrawn at the latest by November

20、 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

21、 following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherla

22、nds, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 4807:2017EN 4807:2017 (E) 4 1 Scope This standard specifies the characteristics of straight welded coupling in heat resisting steel for swivel flange couplings for inc

23、h series aerospace applications. Nominal pressure: The parts shall withstand nominal pressures given in Table 1. The nominal pressure of the assembly depends on associated seal, tube material characteristics, tube diameter and tube wall thickness (see EN 4814). NOTE Assembly in accordance with TR 48

24、15. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any a

25、mendments) applies. EN 2424, Aerospace series Marking of aerospace products EN 2516, Aerospace series Passivation of corrosion resistant steels and decontamination of nickel base alloys EN 3363, Aerospace series Steel FE-CM68 Solution treated Rm 485 MPa Sand or investment casting1)EN 3468, Aerospace

26、 series Steel FE-PA13 Softened 500 Rm 700 MPa Forgings De 100 mm1)EN 3487, Aerospace series Steel FE-PA3601 (X6CrNiTi18-10) Air melted Softened Bar for machining a or D 250 mm 500 MPa Rm 700 MPa EN 4814, Aerospace series Flange couplings up to 21 000 kPa Technical specification Inch series EN 9100,

27、Quality Management Systems Requirements for Aviation, Space and Defence Organizations TR 4815, Aerospace series Flange couplings up to 21 000 kPa Design standard Inch series2)3 Required characteristics 3.1 Configuration Dimensions Tolerances Masses See Figure 1 and Table 1. Dimensions and tolerances

28、 are in millimetres, except otherwise specified. 3.2 Material and surface treatment EN 3363 or EN 3468 or EN 3487. Surface finish: Passivation EN 2516. 1)Published as ASD-STAN Prestandard at the date of publication of this standard. (http:/www.asd-stan.org/)2)Published as ASD-STAN Technical Report a

29、t the date of publication of this standard. (http:/www.asd-stan.org/)BS EN 4807:2017EN 4807:2017 (E) 5 Key 1 3D view (for information only) 2 Constant thickness 3 Marking of identity block 4 Marking of manufacturers monogram Figure 1 BS EN 4807:2017EN4807:2017(E)6Table1DimensionalcodeaNominaldiamete

30、rWall thicknessoftubeABDEFGHJLMNR1x1x2VMassbinchmmnull0,05+0,10null0,20null0,10null0,65minmaxminmaxminnull0,20null0,1null0,8null0,125A10.62515,8750,71128,5031,3019,6013,8027,952,803,053,003,9011,6019,601,03,30,6250,200,10EN4549A01067,5B100,889EN4549B010A12.75019,0500,71131,7036,8523,6017,0030,152,80

31、3,053,204,2014,9023,601,03,30,6250,200,10EN4549A01297,1B120,889EN4549B012A161.00025,4000,71138,0540,1529,8023,0033,152,803,053,604,4020,8029,801,03,30,6250,200,10EN4549A016148,5B160,889EN4549B016A201.25031,7500,71146,8051,3036,3028,9038,753,053,204,004,9026,7536,301,03,30,6250,200,10EN4549A020251,4B

32、200,889EN4549B020A241.50038,1000,71153,9054,6542,4034,8543,553,303,454,405,4031,5042,401,03,30,6250,200,10EN4549A024348,2B240,889EN4549B024A281.75044,4500,71160,3059,9549,3040,8047,853,553,704,805,7037,1049,301,03,30,6250,200,10EN4549A028470,7B280,889EN4549B028A322.00050,8000,71169,8065,4055,6046,75

33、52,153,553,705,206,1042,5055,601,03,30,6250,200,10EN4549A032625,1B320,889EN4549B032aThiscode iscomposedwiththe followingelements:Tube wallthicknesscode (A:0,711mm;B:0,889mm);Nominaldiametergiven in 16thofincheswithin2digit.bMass quotedinkg/1000parts.BS EN 4807:2017EN4807:2017(E)6Table1Dimensionalcod

34、eaNominaldiameterWall thicknessoftubeABDEFGHJLMNR1x1x2VMassbinchmmnull0,05+0,10null0,20null0,10null0,65minmaxminmaxminnull0,20null0,1null0,8null0,125A10.62515,8750,71128,5031,3019,6013,8027,952,803,053,003,9011,6019,601,03,30,6250,200,10EN4549A01067,5B100,889EN4549B010A12.75019,0500,71131,7036,8523,

35、6017,0030,152,803,053,204,2014,9023,601,03,30,6250,200,10EN4549A01297,1B120,889EN4549B012A161.00025,4000,71138,0540,1529,8023,0033,152,803,053,604,4020,8029,801,03,30,6250,200,10EN4549A016148,5B160,889EN4549B016A201.25031,7500,71146,8051,3036,3028,9038,753,053,204,004,9026,7536,301,03,30,6250,200,10

36、EN4549A020251,4B200,889EN4549B020A241.50038,1000,71153,9054,6542,4034,8543,553,303,454,405,4031,5042,401,03,30,6250,200,10EN4549A024348,2B240,889EN4549B024A281.75044,4500,71160,3059,9549,3040,8047,853,553,704,805,7037,1049,301,03,30,6250,200,10EN4549A028470,7B280,889EN4549B028A322.00050,8000,71169,8

37、065,4055,6046,7552,153,553,705,206,1042,5055,601,03,30,6250,200,10EN4549A032625,1B320,889EN4549B032aThiscode iscomposedwiththe followingelements:Tube wallthicknesscode (A:0,711mm;B:0,889mm);Nominaldiametergiven in 16thofincheswithin2digit.bMass quotedinkg/1000parts.EN 4807:2017 (E) 7 4 Designation E

38、XAMPLE NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 5 Identification marking EN 2424, category A, as indicated on Figure 1. 6 Technical specification See EN 4814. 7 Quality Assurance Approval of the manufactures. See EN 9100. BS EN 4807:2017

39、This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are pub

40、lished by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully as

41、sembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more a

42、bout British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can

43、 also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrig

44、hted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any porti

45、on of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purc

46、hased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for p

47、ersonal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need

48、 more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.Subscript

49、ionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can kee