EN 4811-2017 en Aerospace series - Flange couplings - Gasket seal with fluorocarbon seal on aluminium plate with 4 fastening holes - Inch series.pdf

1、BS EN 4811:2017Aerospace series - Flange couplings - Gasket seal with fluorocarbon seal on aluminium plate with 4 fastening holes - Inch seriesBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National forewordThis British Standard is the UK implementation of EN 4811:2

2、017.The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisio

3、ns of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 95342 2ICS 49.080Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published und

4、er the authority of the Standards Policy and Strategy Committee on 30 June 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 4811:2017EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 4811May 2017ICS 49.080EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN D

5、E NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN Ref. No. EN 4811:2017: EAll rights of exploitation in any form and by any means reserved worldwide for CEN national MembersAerospace series - Flange couplings - Gasket seal with flu

6、orocarbon seal on aluminium plate with 4 fastening holes - Inch seriesSrie arospatiale - Raccordement bride - Joint plaque avec joint en fluorocarbone sur plaque en aluminium avec 4 trous de fixation - Srie en inchesLuft- und Raumfahrt - Rohrverschraubung mit Flanschen - Flachdichtung aus Fluorocarb

7、on-Elastomer, mit Aluminiumarmierung mit 4 Befestigungslchern - Inch-ReiheThis European Standard was approved by CEN on 14 November 2016.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national

8、 standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version

9、in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech

10、Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingd

11、om.English VersionEN 4811:2017 (E)European foreword 31 Scope . 42 Normative references 43 Required characteristics 43.1 Configuration Dimensions Tolerances Masses 43.2 Material . 43.3 Surface treatment . 43.4 Adherence . 54 Designation 65 Identification marking . 66 Technical specification . 67 Qual

12、ity Assurance 62Contents PageBS EN 4811:2017EN 4811:2017 (E)European forewordThis document (EN 4811:2017) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN).After enquiries and votes carried out in accordance with the rules of this Associatio

13、n, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at

14、 the latest by November 2017, and conflicting national standards shall be withdrawn at the latest by November 2017.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such p

15、atent rights.According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia

16、, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.3BS EN 4811:2017EN 4811:2017 (E)1 ScopeThis standard specifies the

17、characteristics of gasket seal with fluorocarbon seal on aluminium plate, 4 holes, for pipe couplings for inch series aerospace applications.Nominal pressure: up to 21 000 kPa; depends on the associated tube material and tube wall thickness in the assembly (see EN 4814).Temperature range: 20 C to 20

18、0 C.NOTE Assembly in accordance with TR 4815.This part should not be reused after disassembling.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited appl

19、ies. For undated references, the latest edition of the referenced document (including any amendments) applies.EN 2284 , Aerospace series Sulphuric acid anodizing of aluminium and wrought aluminium alloysEN 2424 , Aerospace series Marking of aerospace productsEN 2693 , Aerospace series Aluminium allo

20、y AL-P5086-H111 Sheet and strip 0,3 mm a 6 mmEN 2699, Aerospace series Aluminium alloy (5086) Annealed and straightened (H111) Drawn bar 6 D 50 mm1)EN 2798, Aerospace series Fluorocarbon rubber (FPM) Low compression set Hardness 80 IRHDEN 4054 , Aerospace series Pipe couplings, loose flanges and sea

21、ls Seals in fluorocarbon rubber and armature in aluminium alloy Technical specificationEN 4814, Aerospace series Flange couplings up to 21 000 kPa Technical specification Inch seriesEN 9100 , Quality Management Systems Requirements for Aviation, Space and Defense OrganizationsTR 4815, Aerospace seri

22、es Flange couplings up to 21 000 kPa Design standard Inch series2)3 Required characteristics3.1 Configuration Dimensions Tolerances MassesSee Figure 1 and Table 1. Dimensions and tolerances are in millimetres, except otherwise specified.3.2 MaterialPlate: EN 2693 or EN 2699.Seal: EN 2798.3.3 Surface

23、 treatmentPlate: EN 2284 BC Green.1) Published as ASD-STAN Prestandard at the date of publication of this standard. ( http:/www.asd-stan.org/ )2) Published as ASD-STAN Technical Report at the date of publication of this standard. ( http:/www.asd-stan.org/ )4 BS EN 4811:2017EN 4811:2017 (E)3.4 Adhere

24、nceTwo parts of seal shall be adhere to the plate and bonded together through equally spaced holes.Key1 3D view2 Marking3 Surface geometric tolerance applies to F and R14 Form not stated are left to the manufacturers discretion. Design and manufacturing of sealing parts dimensioning shall not allow

25、any bead outside lateral cavities while assembling the coupling.Figure 15BS EN 4811:2017EN 4811:2017 (E)Table 1Dimension-al code aNominal diameterA B C D E F R1 R2 Mass binch mm 0,25 Theo. Theo. 0,1 Theo. Theo. Theo. min max 10A .625 15,875 13,5 26,36 13,18 5,1 21,21 28,45 5,56 5,08 8,13 4,110B .625

26、 15,875 13,5 28,30 14,15 6,6 21,21 31,20 6,76 5,08 8,13 5,312A .750 19,050 17,0 29,36 14,68 5,1 24,38 31,75 5,56 5,08 8,13 4,512B .750 19,050 17,0 30,48 15,24 6,6 24,38 40,23 6,76 5,08 8,13 6,716A 1.000 25,400 23,1 33,32 16,66 5,1 30,58 38,10 5,56 5,08 8,13 5,216B 1.000 25,400 23,1 35,92 17,96 6,6 3

27、0,58 46,84 6,76 6,60 9,91 8,120B 1.250 31,750 28,9 42,06 21,03 6,6 37,90 46,84 6,76 6,60 9,91 8,024B 1.500 38,100 34,9 46,02 23,01 6,6 43,94 53,97 7,14 6,60 9,91 9,428B 1.750 44,450 41,2 52,37 26,06 6,6 51,61 60,32 7,14 6,60 9,91 10,732C 2.000 50,800 46,8 60,32 30,17 8,2 61,01 69,85 7,92 7, 87 11,68

28、 14,4aThis code is composed with the following elements: Nominal diameter given in 16thof inches within 2 digit; Bolt nominal thread diameter A: .1900 in (4,826 mm); B: .2500 in (6,35 mm); C: .3125 in (7,938 mm). bMass quoted in kg/1 000 parts 4 DesignationEXAMPLE NOTE If necessary, the code I9005 s

29、hall be placed between the description block and the identity block.5 Identification markingEN 2424 , category A, as indicated on Figure 1.6 Technical specificationEN 4054 with minimum pressure values for ageing and pressurizing tests.7 Quality AssuranceApproval of the manufactures.See EN 9100 .6 BS

30、 EN 4811:2017This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standa

31、rds Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependa

32、ble format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standar

33、ds by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased.

34、If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some

35、person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard t

36、o any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy f

37、ormat is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal

38、company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of

39、 the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of sub

40、scription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7

41、and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BS

42、I Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publ

43、ications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revis

44、ion. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enqu

45、iries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Group Headquarters389 Chiswick High Road London W4 4AL UKBSI Back Cover.indd 1 27/01/2016 14:20