EN 485-4-1993 en Aluminium and Aluminium Alloys - Sheet Strip and Plate - Part 4 Tolerances on Shape and Dimensions for Cold-Rolled Products《铝和铝合金 片材 带材和板材 第4部分 冷轧制品的形状和尺寸公差》.pdf

1、CEN EN*485-4 93 W 3404.587 0054537 047 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 485-4 October 1993 GDC 669.71-41-122.2 : 669.715.018.26 Descriptors: Iron and steel products, cold-rolled products, rolled products, nietal plates, steel strips, aluniiniuiii, aluminium alloys, dimensional to

2、lerances, form tolerances English version Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products Aluminium et alliages daluniiniiim - mles, bandes et tles paisses - Partie 4: Tolrances sur forme et dimensions des produits lamins

3、froid Aluminium und Aluminiumlegierungen - Bnder, Bleche und Platten - Bi1 4: GrenZabmaBe und Formtoleranzen fr kaltgewalzte Erzeugnisse This European Standard was approved by CEN on 1993-10-08. CEN inenibeis are bound to comply with the CEWCENELEC Internal Regulations which stipulate the conditions

4、 for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three offici

5、al versions (English, French, German). A veision in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the saine status as the official versions. CEN inenibeis are the national standards bodies of Austria,

6、 Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Ketherlands, Norway, Poitugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Conunittee for Standardizat.ion Comit Europen de Normalisation Europisches Komitee fiir Normung Central Secretariat: ru

7、e de Stassart 36, B-1050 Brussels 5 1993 Copyright reserved to CEN inembeis Ref. No. EN 485-4 : 1993 E CEN ENx485-4 93 3404589 0054518 T83 Page 2 EN 485-4 : 1993 Foreword Contents This European Standard has been drawn up by CEN/TC 132 Aluminium and aluminium alloys, whose Secretariat is held by the

8、Association fianaise de Normalisation (AFNOR). Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 7 Sheet, strip and plate to work out the following standard: EN 485-4 Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: lblerances on dimensions and for

9、m for cold-rolled products. This standard is part of a set of four standards. The other standards deal with: EN 485-1 Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: %chnical conditions for inspection and delivery. EN 485-2 Aluminium and aluminium alloys - Sheet, strip and plate -

10、Part 2: Mechanical properties. EN 485-3 Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: lblerances on dimensions and form for hot-rolled products. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement,

11、at the latest by Apiil 1994, and conflicting national standards shall be withdrawn at the latest by Apiil 1994. The Standard was approved and in accordance with the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Fin

12、land, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Noway, Portugal, Spain, Sweden, Switzerland, United Kingdom. Foreword 1 Scope 2 Normative references 3 Dimensional tolerances 3.1 Thickness 3.2 Width 3.3 Length 4 Shape tolerances 4.1 Lateral curvature 4.2 Flatness 4.3

13、Squareness Annex A (normative) Alloy split into Group I and Group II Annex B (noimative) Other thickness tolerances Page 2 3 3 3 3 5 5 6 6 6 6 10 10 1s This Part of EN 485 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy sheet, strip and plate obtained by co

14、ld-rolling, for general engineering applications. It applies to products with a thickness over 0,20 mm up to and including 50 mm. It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, e

15、tc. sheet and strip or to special applications such as aerospace, can stock, etc. which are dealt with in separate European Standards. Technical conditions for inspection and delivery of products covered by this standard are specified in Eh 485- 1. 2 Normative references This European Standard incor

16、porates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this Euro

17、pean Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. 3 Dimensional toleranc 3.1 Thickness Page 3 EN 4854 : 1993 S 3.1.1 For the purpose of this European Standard the alloys are distributed into two grou

18、ps which correspond to varying difficulty when manufacturing the products. Tighter thickness tolerances apply to Group I alloys (soft alloys). The grouping is carried out according to the specified chenucal composition limits of the alloys (see EN 573-3) as follows: - Group I alloys: - 1000 series a

19、lloys; - non heat-treatable 7000 and 8000 series alloys; - 4000 series alloys with less than 2 $6 maximum specified silicon content; - 3000 and 5000 series alloys for which the maximum specified magnesium and manganese contents are each no greater than 1,s % and their sum no greater than 2,3 %. - al

20、l alloys which do not belong to Group I. The split into Group I and Group II of the most commonly used general engineering alloys is given in annex A (see table Al). 3.1.2 Thickness tolerances for sheet, strip and plate are specified in table 1. 3.1.3 Other thickness tolerances may be agreed between

21、 supplier and purchaser. They are specified in annex B. - Group II alloys: CEN EN*485-4 93 E 3404589 0054520 631 = Specified thickness Over Up to and including Page 4 EN 485-4 : 1993 Thickness tolerance for specified width Up to and including 1000 to and to and to and to and to and to and Over 1000

22、up including 1250 including 1600 including Zoo0 including including including Over 1280 up Over 1800 up Over 2000 up Over 2500 up Over 3000 up 2500 3000 3500 Alloy Group Alloy Group Alloy Group Alloy Group Alloy Group Alloy Group Alloy Group I III I III I III I (II and I and II I and II f 0,05 f 0,0

23、6 f 0,07 f 0,08 f 0,07 f 0,08 f 0,09 f 0,07 f 0,08 f 0,11 - - f 0,08 f 0,09 f 0,12 - - f 0,09 f 0,10 f 0,13 - - 0,s 0,8 1,5 1,8 2,5 0,G f 0,03 f 0,04 f 0,05 f 0,06 o,T-r- f 0,03 f 0,04 f 0,06 f 0,07 1,0 f 0,04 f 0,05 f 0,06 f 0,08 f 0,04 If 0,05 If 0,07 If 0,09 If 0,09 f 0,05 f 0:07 f 0,09 f 0,11 f

24、0,10 f 0,06 f 0,08 f 0,10 f 0,12 f 0,11 f 0,06 f 0,09 f 0,11 f 0,13 f 0,12 f 0,07 f 0.10 f 0,12 f 0,14 f 0,13 f 0.12 If 0.11 If 0.14 If 0.16 - - f 0,141f 0,14)* 0,16(f 0,19 140 15,O If 0,18 If 0,22 If 0,24 If 0,26 If 0.29 If 0.36 If oz - - 15,o I6,O If 0,20 If 0,24 If 0,25 If 0,26 (f 0,32 If 0,40 If

25、 0,46 f 0,15 If 0,15 If 0.17 If 0.20 6,O 8,0 If 0,24 (f 0,30 If 0,31 (f 0,32 (f 0,38 (f 0,44 (f 0,50 8,O 110 If 0,27 If 0,33 If 0,36 If 0,38 If 0,44 If 0,50 If 0,56 10 I12 If 0,32 If 0.38 If 0,40 If 0,41 If 0.47 If 0,53 If 0.59 - - ( f 0,51 1 f 0.57 1 f 0,63 12 115 If 0,36 If 0,42 If 0,43 (f 0,45 15

26、 120 If 0,38 If 0,44 If 0,46 If 0,48 (f 0,54 If 0,60 If 0,66 (f 0,40 (f 0,46 If 0,48 If 0,50 If 0,56 If 0,62 If 0,68 20 I25 3,0 13,5 If 0,10 If 0,121f 0,151f 0,171f 0,17(f 0,191f 0,18)f 0,20(f 0,24 (25 (30 If 0,45 If 0,50 (f 0,53 (f 0,55 (f 0,60 (f 0,65 If 0,70 - - 130 140 If 0,50 If 0,55 If 0,58 If

27、 0,60 (f 0,65 If 0,70 If 0,75 40 150 If 0,55 (f 0,60 If 0,63 If 0,65 If 0,70 If 0,75 If 0,80 When measuring the thickness. a zone 10 mm wide from the edges of the product shall be disregarded. CEN ENx485-4 93 = 3404589 0054521 578 Over 500 up to and including 1250 Over 12W up to and to and including

28、 16W including 2600 Over 16W up + 1,5 O f 2.5 t3 O O + O,7 O + 1,2 O -2 O + 2,6 +3 O o Up to and including Up to and including 500 -6 LS o O +8 +8 O O Up to and including lover I Up to and including 1000 +4 o +G O Page 5 EN 485-4 : 1993 3.2 Width 3.2.1 Width tolerances for strip are specified in tab

29、le 2. 3.2.2 Width tolerances for sheet and plate are specified in table 3. 3.3 Length 3.3.1 Length tolerances for strip are not specified. 3.3.2 Length tolerances for sheet and plate are specified in table 4. I ihble 2. Width tolerances for strip Dimensions in niiilinietres 1 I Specified thickness 1

30、 Over Width tolerance for specified width Up to and including Up to and including 100 i_ o,20 O,B + o,3 O + 1,s O I + ;I8 I+: + 0,4 o I j 0,B 1,O - O,3 O + 0,4 o + O,6 O 2,0 3,o -t 1 o tl o I + +2 O I + o 2,6 10 Is,n 5,0 I+; + 1,8 O f3 O I+: 1 able 3. Width tolerances for sheet and plate i niiiiensi

31、oiis in iiiilliiiietres I I Specified thickness I Width tolerance for specified width I I Over I 1250 I+: l- +3 O 1-0 I +8 O +4 O I Itible 4. Length tolerances for sheet and plate Diiiieiisions in inillinietres Specified thickness 1 Length tolerance for specified length Over 5 Over 3 up to and inclu

32、ding 1.3 o + 0,2 % of specified length 1 0,o +G If8 o o I + 10 (1 +8 o I + O CEN EN*485=4 93 3404589 0054522 404 II Page 6 EN 485-4 : 1993 4 Shape tolerances 4.1 Lateral curvature 4.1.1 Lateral curvature tolerances for strip with width up to and including 3500 mm are specified in table 5. Jhble 5. L

33、ateral curvature tolerances for strip (measured on 2000 mm strip length) Dimensions in miimetres 1 Specified width Lateral curvature Over 1 up to and including d, 100 I300 (6 300 I600 I 600 11000 14 1000 I2000 2000 I3500 I ) For widt.hs less than 25 mm the tolerances are to be agreed between purchas

34、er and supplier. The deviation from straightness, d, is measured as indicated in figure 1, for a length L of 2000 mm, from one end of the strip, while the strip is resting on a horizontal base plate. 4.1.2 Lateral curvature tolerances for sheet and plate are specified in table 6. The deviation from

35、straightness, d, is measured as indicated in figure 1, while the sheet or plate is resting on a horizontal base plate. 4.2 Flatness 4.2.1 Flatness tolerances for strip are not specified. 4.2.2 Flatness tolerances for sheet and plate are specified in table 7 and are expressed as a percentage of the l

36、ength L and /or the width W and /or the measured chord length 1. Deviation from flatness, d, resulting from arching, buckling or edge waves, is measured as shown in figures 2 to 5, using a lightweight straightedge and a feeler gauge, dial gauge or scale, while the sheet or plate is resting on a hori

37、zontal base plate concave side upwards. These tolerances do not apply to sheet and plate supplied in the O (annealed) or F (as fabricated) tempers or to blight sheet. These tolerances do not include end or cornei turnup. 4.3 Squareness 4.3.1 Squareness tolerances for strip are not specified. 4.3.2 S

38、quareness tolerances for sheet and plate are specified in table 8. The squaieness tolerance is expressed as the maximum allowable difference in length of diagonals AA and BB as shown in figure 6. Side edge (concave side) I-= Straightedge o / Plate or sheet 4- CI = deviation from straightness L = len

39、gth of the sheet or plate Figure 1. Lateral curvature of plate or sheet of length L (see 4.1.2) - - CEN EN*485-4 93 3404589 0054523 340 U Page 7 EN 485-4 : 1993 Over Up to and Up to and Over loo0 up to Over 2000 up to including including 1000 and including and including 2000 3500 2 loo1) 300 2 4 8 3

40、00 600 3 5 600 1000 1 2 4 1000 2000 - 2 4 4 2000 3500 - - mble 6. Lateral curvature tolerances for sheet and plate Dimensions in miiiinietres Over 3500 up to and including and including 5Ooo 16000 Over up to - - - - 5 0.1 % of 5 5 specified length Specified thickness mm Over Up to and including 0,20

41、 l0,50 A-A Total deviation Partial deviation P, /a, on length on width % (for a chord of at least 300 nim) d“lc1rL (fn1lnidrl wr 4,ld by agreement by agreement by agreement d = deviation from flatness it = width of the sheet or plate Figure 2. Transverse arch (see 4.2.2) CEN EN*485-4 73 3404589 0054

42、524 287 Page 8 EN 485-4 : 1993 A- A al L d = deviation from flatness L = length of the sheet or plate Figure 3. Longitudinal arch (see 4.2.2) 1 I A- A bl d = deviation from flatness I = length of buckle (chord) Figure 4. Buckles (see 4.2.2) CEN ENx485-4 93 3404589 0054525 LI3 Page 9 EN 4854 : 1993 i

43、ncluding 56 6 2000 56 6 1000 2000 3000 56 6 3000 5000 56 6 5000 15000 56 6 I loo0 A- A Up to and including loo0 and including and including Over 1000 up to 1500 2000 Over 1500 up to - - 4 5 4 5 6 6 7 8 5 5 7 7 7 9 6 8 8 8 10 10 10 10 12 12 12 15 - - d = deviation from flatness 1 = length of edge wav

44、e (chord) Figure 5. Edge waves (see 4.2.2) Iable 8. Squareness tolerances for sheet and plate Dimensions in millimetres Soecified length 1 Specified I Squareness tolerance for specified width Over 2000 up to and including 3500 - - 8 10 10 12 12 15 Page 10 EN 485-4 : 1993 - CEN EN*485-4 93 I 3404589

45、O054526 05T I 2, Figure 6. Measurement of squareness (see 4.3.2) Annex A (normative) Alloy split into Group I and Group II lhble Al. All Group I Group II y Groups 1080A 1070A 1050A 1200 3003 3103 3005 3105 4006 4007 5005 5050 8011A 2014 2017A 2024 3004 5040 5049 5251 5052 5154A 5454 5754 5182 5083 5086 6061 6082 7020 7021 7022 7075 Annex B (normative) Other thickness tolerances