EN 508-1-2014 en Roofing and cladding products from metal sheet - Specification for self-supporting of steel aluminium or stainless steel sheet - Part 1 Steel《金属片的屋顶及其覆层产品 钢，铝或不锈钢板.pdf

1、BSI Standards PublicationBS EN 508-1:2014Roofing and claddingproducts from metal sheet Specification for self-supporting of steel, aluminiumor stainless steel sheetPart 1: SteelBS EN 508-1:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 508-1:2014. Itsupers

2、edes BS EN 508-1:2008 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/542/6, Corrugated sheeting materials.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include al

3、l the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 83430 1ICS 91.060.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Sta

4、ndard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2014.Amendments issued since publicationDate Text affectedBS EN 508-1:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 508-1 May 2014 ICS 91.060.20 Supersedes EN 508-1:2008English Version Roofing

5、 and cladding products from metal sheet - Specification for self-supporting of steel, aluminium or stainless steel sheet - Part 1: Steel Produits de couverture et de bardage en tle mtallique - Spcification pour les produits autoportants en tles dacier, daluminium ou dacier inoxydable - Partie 1: Aci

6、er Dachdeckungs- und Wandbekleidungsprodukte aus Metallblech - Spezifikation fr selbsttragende Dachdeckungsprodukte aus Stahlblech, Aluminiumblech oder nichtrostendem Stahlblech - Teil 1: Stahl This European Standard was approved by CEN on 1 March 2014. CEN members are bound to comply with the CEN/C

7、ENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centr

8、e or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the

9、official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherla

10、nds, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights

11、 of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 508-1:2014 EBS EN 508-1:2014EN 508-1:2014 (E) 2 Contents Page Foreword 4 Introduction .5 1 Scope 6 2 Normative references 6 3 Terms, definitions, symbols and abbreviations .7 3.1 General 7 3.2 Mate

12、rials .7 3.3 Profile definitions.8 3.4 Product geometry . 10 3.5 Symbols and abbreviations . 13 4 Requirements 14 4.1 General . 14 4.2 Materials 14 4.2.1 Materials for roll formed and brake pressed profiles 14 4.2.2 Materials for tiles 15 4.2.3 Nominal metallic coating . 15 4.2.4 Organic coatings. 1

13、5 4.3 Products 16 4.3.1 Mechanical resistance 16 4.3.2 Calculation and test of mechanical resistance 16 4.3.3 Dimensions 17 4.3.4 Dimensional tolerances for the profiled sheets 17 4.3.5 Safety in case of fire . 17 5 Test methods . 18 5.1 Material properties 18 5.2 Mechanical properties 18 6 Designat

14、ion . 18 7 Marking, labelling and packaging . 18 7.1 Marking and labelling . 18 7.2 Packaging and special ordering conditions 19 7.3 Transport, storage and handling . 19 Annex A (informative) Aluminium coated steel sheet (type A) . 20 A.1 General . 20 A.2 Specification for roof covering or cladding

15、products . 20 A.2.1 Steel grades . 20 A.2.2 Coating mass 20 A.2.3 Dimensional tolerances . 20 Annex B (normative) Multilayer coated steel sheet . 21 B.1 General . 21 B.2 Substrate material. 21 B.3 Specific requirements 21 B.3.1 Minimum nominal values of thickness . 21 B.3.2 Bituminous coating specif

16、ication . 21 B.3.3 Durability . 22 BS EN 508-1:2014EN 508-1:2014 (E) 3 B.4 Freedom from defects . 22 Annex C (informative) Metallic coatings . 23 Annex D (normative) Dimensional tolerances . 26 D.1 Tolerances for trapezoidal sheets . 26 D.1.1 General . 26 D.1.2 Depth of profile 26 D.1.3 Depth of sti

17、ffeners . 27 D.1.4 Pitch 28 D.1.5 Widths of crown and valley 29 D.1.6 Cover width 30 D.1.7 Radius of bends . 31 D.1.8 Deviation from straightness . 31 D.1.9 Deviation from squareness 32 D.1.10 Length . 33 D.1.11 Deviation of side lap 34 D.1.12 Curve radius and angles . 35 D.2 Tolerances for sinusoid

18、al profiles . 35 D.3 Tolerances on tiles 35 D.3.1 General . 35 D.3.2 Depth of tile 36 D.3.3 Web angular displacement (Figure D.13) 37 D.3.4 Pitch 37 D.3.5 Width of crown and valley (Figure D.15) . 38 D.3.6 Cover width 38 D.3.7 Radius of bends . 39 D.3.8 Deviation from straightness . 39 D.3.9 Deviati

19、on from squareness 40 D.3.10 Length . 40 D.3.11 Contraction or bulging 40 D.4 Methods for measuring profiles . 41 D.4.1 General . 41 D.4.2 Depth of profile 41 D.4.3 Depth of stiffeners . 42 D.4.4 Pitch 42 D.4.5 Width of crown and valley 43 D.4.6 Cover width 43 D.4.7 Radius of bends . 43 D.4.8 Straig

20、htness . 43 D.4.9 Squareness 43 D.4.10 Length . 44 D.4.11 Side laps . 44 Bibliography 45 BS EN 508-1:2014EN 508-1:2014 (E) 4 Foreword This document (EN 508-1:2014) has been prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying and products for wall cladding”, th

21、e secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2014 and conflicting national standards shall be withdrawn at the latest by November 2014. Attention

22、 is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 508-1:2008. EN 508 Roofing products from metal sheet - Specificatio

23、n for self-supporting products of steel, aluminium or stainless steel sheet consists of the following parts: Part 1: Steel Part 2: Aluminium Part 3: Stainless steel According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to impleme

24、nt this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, S

25、lovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 508-1:2014EN 508-1:2014 (E) 5 Introduction Figure 1 indicates the position of this European Standard in the CEN framework of standards concerning roofing products of metal. Figure 1 Framework of standards In this Eur

26、opean Standard, the performance of the product has been defined in terms of calculation and a number of type tests. The performance of a roof constructed with these products depends not only on the properties of the product as required by this European Standard, but also on the design, construction

27、and performance of the roof as a whole in relation to the environment and conditions of use. BS EN 508-1:2014EN 508-1:2014 (E) 6 1 Scope This part of EN 508 specifies requirements for self-supporting roofing, covering, wall cladding, lining, liner trays and tiles products for discontinuous laying ma

28、de from metallic coated steel sheet with or without additional organic coatings. Sheets intended to be used with insulation and membranes are also covered. This European Standard establishes general characteristics, definitions, classifications and labelling for the products, together with requireme

29、nts for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply when purchased before they are despatched from the factory. It specifies

30、 the requirements for products which enable them to meet all normal service conditions. This European Standard applies to all discontinuously laid self-supporting external profiled sheets for roofing covering, wall cladding, lining and liner trays with the exception of tiles with a surface area less

31、 than 1 m2and produced by stamping. These profiled sheets are designed to keep wind, rain and snow out of the building and to transfer any resultant loads and infrequent maintenance loads to the structure. This European Standard does not cover products for structural purposes, i.e. it does cover pro

32、ducts used in constructions of Class III (according to EN 1993-1-3), it does not cover products used in constructions of Classes I and II (according to EN 1993-1-3) intended to contribute to the global or partial stability of the building structure by providing racking resistance or resistance to pe

33、rmanent static loads (excluding self-weight of the metal sheet). No requirements for supporting construction, design of roof, cladding, lining, tile system and execution of connections and flashings are included. 2 Normative references The following documents, in whole or in part, are normatively re

34、ferenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10143, Continuously hot-dip coated steel sheet and strip - Tolerance

35、s on dimensions and shape EN 10169:2010+A1:2012, Continuously organic coated (coil coated) steel flat products - Technical delivery conditions EN 10346, Continuously hot-dip coated steel flat products - Technical delivery conditions EN 14782, Self-supporting metal sheet for roofing, external claddin

36、g and internal lining - Product specification and requirements EN ISO 6270-1, Paints and varnishes - Determination of resistance to humidity - Part 1: Continuous condensation (ISO 6270-1) EN ISO 6988, Metallic and other non-organic coatings - Sulfur dioxide test with general condensation of moisture

37、 (ISO 6988) EN ISO 9227, Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227) BS EN 508-1:2014EN 508-1:2014 (E) 7 3 Terms, definitions, symbols and abbreviations For the purposes of this document, the terms and definitions given in EN 10169:2010+A1:2012 and the following apply. 3.

38、1 General 3.1.1 self-supporting product product which will, by virtue of its material and shape, support all applied loadings (e.g. snow, wind, foot traffic, insulation, membrane) and transmit these loadings to spaced structural supports 3.2 Materials 3.2.1 hot-dip zinc coated steel sheet (type Z) p

39、roduct obtained by continuously hot-dip zinc coating cold reduced strips of either low carbon steel for cold forming or steel of structural quality Note 1 to entry: For steel of structural quality, see EN 10346. 3.2.2 hot-dip 5 % Al-Zn coated steel sheet (type ZA) product obtained by continuously ho

40、t-dip coating cold reduced strips of low carbon steel for cold forming or steel of structural quality on a production line using an alloy consisting of zinc and approximately 5 % aluminium (nominal percentage by mass) Note 1 to entry: For steel of structural quality, see EN 10346. 3.2.3 hot-dip 55 %

41、 Al-Zn coated steel sheet (type AZ) product obtained by continuously hot-dip coating cold reduced strips of low carbon steel for cold forming or steel of structural quality on a production line using an alloy consisting of: 55 % aluminium (nominal percentage by mass); 1,6 % silicon (nominal percenta

42、ge by mass); and the balance zinc Note 1 to entry: For steel of structural quality, see EN 10346. 3.2.4 hot-dip aluminium coated steel sheet (type A) product obtained by continuously hot-dip aluminium coating cold reduced strips of low carbon steel for cold forming steel or steel of structural quali

43、ty on a production line Note 1 to entry: See Annex A. 3.2.5 organic coated steel sheet product obtained by factory application of paint by roller or spray processes, or factory application of laminated organic film, on substrates of type Z, type ZA, type AZ or type A coated steel sheet Note 1 to ent

44、ry: EN 10169 refers to this type of coated steel. BS EN 508-1:2014EN 508-1:2014 (E) 8 3.2.6 multilayer coated steel sheet product obtained by continuously coating on both sides hot-dip zinc coated cold reduced strips of low carbon steel for cold forming or steel of structural quality with one or mul

45、tiple applications of thermoplastic asphalt compounds (minimum thickness 1,5 mm) and subsequent lamination of a metal foil with or without decorative painting Note 1 to entry: See Annex B. 3.3 Profile definitions 3.3.1 trapezoidal profiled sheet self-supporting sheet which is designed to allow it to

46、 be side and end lapped, the crowns of which may be rounded and, in addition, the crowns, webs and valleys may be stiffened Note 1 to entry: See Figures 2 to 5. Figure 2 Part of typical trapezoidal profile Figure 3 Part of typical trapezoidal profile with rounded crowns Figure 4 Part of typical trap

47、ezoidal profile with stiffened crown and web Figure 5 Part of typical trapezoidal profile with stiffened valley BS EN 508-1:2014EN 508-1:2014 (E) 9 3.3.2 sinusoidal profiled sheet self-supporting sheet which is designed to allow it to be side and end lapped, comprising a series of arc shaped crowns

48、and valleys interconnected with tangential webs Note 1 to entry: See Figure 6. Figure 6 Part of typical sinusoidal profiled sheet 3.3.3 standing seam and concealed fix sheet self-supporting sheet profiled in such a way that the fixings are hidden within the construction and are not exposed to the we

49、ather Note 1 to entry: The profile shape is designed to allow the formation of side laps on site. Note 2 to entry: As these types of roof covering products are used in proprietary roofing or cladding systems, no structural requirements are given within this part of EN 508. Note 3 to entry: See Figures 7 and 8. Note 4 to entry: These products are normally designed by testing. Figure 7 Typical standing seam profile BS EN 508-1:2014EN 508-1:2014 (E) 10 Figure 8 Typical concealed fix profile 3.3.4 tile profiles parts of typical tile profiled sheets