1、BS EN 508-2:2008ICS 91.060.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDRoofing productsfrom metal sheet Specification for selfsupporting productsof steel, aluminium orstainless steel sheetPart 2: AluminiumIncorporating Corrigendum 2009MayThis British Stand
2、ardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 March2009 BSI 2009ISBN 978 0 580 67409 9 Amendments/corrigenda issued since publicationDate CommentsBS EN 508-2:2008National forewordThis British Standard is the UK implementation of . It supersedes BSEN 508-2:200
3、0 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee B/542/5, Sheet roof and wall coverings.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary prov
4、isionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.EN 508-2:20083 2009 Replacement of CEN ratified text 1 May EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 508-2July 2008ICS 91.060.20 Supersedes E
5、N 508-2:2000 English VersionRoofing products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet -Part 2: AluminiumProduits de couverture en tle mtallique - Spcificationpour les plaques de couverture en tle dacier, daluminiumou dacier inoxydable
6、 - Partie 2 : AluminiumDachdeckungsprodukte aus Metallblech - Spezifikation frselbsttragende Bedachungselemente aus Stahlblech,Aluminiumblech oder nichtrostendem Stahlblech - Teil 2:AluminiumThis European Standard was approved by CEN on 30 May 2008.CEN members are bound to comply with the CEN/CENELE
7、C Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN
8、 member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN memb
9、ers are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Sw
10、itzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. E
11、N 508-2:2008: EBS EN 508-2:2008EN 508-2:2008 (E) 2 Contents Page Foreword4 Introduction .5 1 Scope 6 2 Normative references 6 3 Terms and definitions, symbols and abbreviations.6 3.1 General6 3.2 Material definitions 6 3.3 Profile definitions.7 3.4 Product geometry 9 3.5 Symbols and abbreviations 12
12、 4 Requirements.13 4.1 General13 4.2 Materials .13 4.2.1 Aluminium 13 4.2.2 Organic coatings14 4.3 Products .15 4.3.1 Mechanical resistance.15 4.3.2 Calculation and tests of mechanical resistance.15 4.3.3. Dimensions.15 4.3.4 Dimensional tolerances for the profiled sheet .16 4.3.5 Safety in case of
13、fire16 5 Test methods16 5.1 Material properties.16 5.2 Surface properties .16 5.3 Structural properties .16 6 Designation 16 7 Marking, labelling and packaging 17 7.1 Marking and labelling 17 7.2 Packaging and special ordering conditions .17 7.3 Transport, storage and handling17 Annex A (normative)
14、Dimensional tolerances 18 A.1 Tolerances for trapezoidal sheets18 A.1.1 General18 A.1.2 Depth of profile 18 A.1.3 Depth of stiffeners .19 A.1.4 Pitch 19 A.1.5 Widths of crown and valley 20 A.1.6 Cover width 20 A.1.7 Radius of bends.21 A.1.8 Deviation from straightness .22 A.1.9 Deviation from square
15、ness.23 A.1.10 Length .23 A.1.11 Deviation of side lap24 A.1.12 Curve radius and angles .24 A.2 Tolerances for sinusoidal profiles .25 A.3 Tolerances on tiles 25 A.3.1 General25 A.3.2 Depth of tile 26 A.3.3 Web angular displacement (Figure A.12) 27 BS EN 508-2:2008EN 508-2:2008 (E) 3 A.3.4 Pitch27 A
16、.3.5 Width of crown and valley (Figure A.14).27 A.3.6 Cover width 28 A.3.7 Radius of bends.28 A.3.8 Deviation from straightness.29 A.3.9 Deviation from squareness 29 A.3.10 Length.30 A.3.11 Contraction or bulging30 A.4 Methods for measuring profiles.31 A.4.1 General .31 A.4.2 Depth of profile 31 A.4
17、.3 Depth of stiffeners.31 A.4.4 Pitch31 A.4.5 Width of crown and valley 32 A.4.6 Cover width 33 A.4.7 Radius of bends.33 A.4.8 Straightness.33 A.4.9 Squareness 33 A.4.10 Length.33 A.4.11 Side laps.33 A.4.12 Side lap ripple 33 Annex B (informative) Test methods for concentrated load 35 Bibliography36
18、 BS EN 508-2:2008EN 508-2:2008 (E) 4 Foreword This document (EN 508-2:2008) has been prepared by Technical Committee CEN/TC 128 “Roof covering for discontinuous laying and products for wall cladding”, the secretariat of which is held by NBN. This European Standard shall be given the status of a nati
19、onal standard, either by publication of an identical text or by endorsement, at the latest by January 2009, and conflicting national standards shall be withdrawn at the latest by January 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of pate
20、nt rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 508-2:2000. EN 508 Roofing products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet consists of the follow
21、ing parts: Part 1: Steel; Part 2: Aluminium; Part 3: Stainless steel. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia
22、, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 508-2:2008EN 508-2:2008 (E) 5 Introduction Figure 1 indicates the p
23、osition of this standard in the CEN framework of standards concerning roofing products of metal. Roofing products of metal Self-supporting products Fully supported products EN 14782 Copper / Zinc EN 506 Steel EN 508-1 Aluminium EN 508-2 Stainless steel EN 508-3 Figure 1 Framework of standards In thi
24、s standard the performance of the product has been defined in terms of calculation and a number of type tests. The performance of a roof constructed with these products depends not only on the properties of the product as required by this standard, but also on the design, construction and performanc
25、e of the roof as a whole in relation to the environment and conditions of use. BS EN 508-2:2008EN 508-2:2008 (E) 6 1 Scope This part of EN 508 specifies requirements for self-supporting roofing products for discontinuous laying made from aluminium sheet with or without additional organic coatings. T
26、he standard establishes general characteristics, definitions, classifications and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requ
27、irements or by purchasers to verify that the products comply before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions. The standard applies to all discontinuously laid self-supporting external profiled sheets for
28、roofing. These profiled roof sheets are designed to keep wind, rain and snow out of the building, and to transfer any resultant loads and infrequent maintenance loads to the structure. No requirements for supporting construction, design of roof system and execution of connections and flashings are i
29、ncluded. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 485-4, Alumini
30、um and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products. EN 1396, Aluminium and aluminium alloys - Coil-coated sheet and strip for general applications Specifications. 3 Terms and definitions, symbols and abbreviations For the purposes o
31、f this document, the following terms and definitions apply. 3.1 General 3.1.1 self-supporting product Product which will, by virtue of its material and shape, support all applied loadings (e.g. snow, wind, foot traffic), and transmit these loadings to spaced structural supports 3.2 Material definiti
32、ons 3.2.1 aluminium unalloyed aluminium or aluminium 3.2.2 unalloyed aluminium metal with a minimum content of 99,0% by mass of aluminium and with content by mass of any other element within the following limits : a total content of iron and silicon not greater than 1,0% ; BS EN 508-2:2008EN 508-2:2
33、008 (E) 7 a content of any other element not greater than 0,10% except for copper which can have a content of up to 0,20% provided that neither the chromium nor the manganese content exceeds 0,05%. 3.2.3 aluminium alloy alloy in which aluminium predominates by mass overreach of the other elements an
34、d which is not covered by the definition of unalloyed aluminium 3.2.4 temper material conditions after a production stage, for example mechanical treatment and/or heat treatment, intended to give the material physical and/or metallurgical properties 3.2.5 organic coated aluminium sheet painted, post
35、 coated, laminated or coil coated (continuously organic coated) aluminium on one or on both sides 3.3 Profile definitions 3.3.1 trapezoidal profiled sheet self-supporting sheet which is designed to allow it to be side and end lapped, the crowns of which may be rounded and, in addition, the crowns, w
36、eb and valley may be stiffened NOTE See Figures 2, 3, 4 and 5. Figure 2 Part of typical trapezoidal profile Figure 3 Part of typical trapezoidal profile with rounded crowns Figure 4 Part of typical trapezoidal profile with stiffened crown and web BS EN 508-2:2008EN 508-2:2008 (E) 8 Figure 5 Part of
37、typical trapezoidal profile with stiffened valley 3.3.2 sinusoidal profiled sheet self-supporting sheet which is designed to allow it to be side and end lapped, comprising a series of arc shaped crowns and valleys interconnected with tangential webs NOTE See Figure 6. Figure 6 Part of typical sinuso
38、idal profiled sheet. 3.3.3 standing seam and concealed fix sheet self-supporting sheet profiled in such a way that the fixings are hidden within the construction and are not exposed to the weather NOTE 1 See Figures 7 and 8. NOTE 2 The profile shape is designed to allow the formation of side laps on
39、 site. NOTE 3 As these types of roof covering products are used in proprietary roofing systems, no structural requirements are given within this standard. NOTE 4 These products are normally designed by testing. Figure 7 Typical standing seam profile BS EN 508-2:2008EN 508-2:2008 (E) 9 Figure 8 Typic
40、al concealed fix profile 3.3.4 tile profiles parts of typical tile profiled sheets that can allow the sheet to be side and/or end lapped NOTE 1 See figures 9a, 9b and 9c. NOTE 2 The tile profiles may include transverse steps. NOTE 3 As these types of roof covering products are used in proprietary sy
41、stems no structural requirements are given within this part of EN 508. NOTE 4 These products are normally designed by testing. Figure 9 Typical tile profiles 3.4 Product geometry NOTE The names for various parts of typical trapezoidal profiled sheets are given in Figures 10a and 10b, with additional
42、 definitions for sinusoidal profiles in Figure 11 and tile profiles in Figure 12. BS EN 508-2:2008EN 508-2:2008 (E) 10 Key 1 Cover width 7 Depth 2 Valley stiffener 8 Valley 3 Rib 9 Pitch 4 Web stiffener 10 Crown 5 Trough 11 Drainage groove 6 Web 12 Crown stiffener a) Definitions of the parts of typi
43、cal trapezoidal profiled sheets BS EN 508-2:2008EN 508-2:2008 (E) 11 Key 1 Bend radius 2 End lap 3 Web angle 4 Overlap 5 Underlap 6 Side lap in principle the same on tiles b) Definitions of the parts of typical trapezoidal profiled sheets Figure 10: Definitions of the parts of typical profiled sheet
44、s BS EN 508-2:2008EN 508-2:2008 (E) 12 Key 1 Depth 2 Pitch Figure 10 Definitions of the parts of typical sinusoidal profiled sheets Key 1 Height of the step 2 Length of the step 3 Number of steps 4 End lap Figure 11 Definitions of the parts of typical tile 3.5 Symbols and abbreviations AA The symbol
45、s for aluminium sheets are the alloy symbols as in 4.2.1 H Aluminium temper symbol AY Acrylic paint coating SP Polyester paint coating SP-SI Silicone-modified polyester paint coating BS EN 508-2:2008EN 508-2:2008 (E) 13 PVDF Polyvinylidenefluoride paint coating PVF(F) Polyvinylfluoride film coating
46、SP-PA Polyamid-modified polyester paint coating PUR Polyurethane paint coating PUR-PA Polyamide-modified polyurethane paint coating AK Alkyd paint coating EP Epoxy paint coating for use within a building 4 Requirements 4.1 General The product shall be manufactured from materials complying with claus
47、e 4.2. NOTE 1 The supplier of the materials is responsible for carrying out the tests necessary to verify that the materials supplied to the manufacturer comply with the requirements and should provide appropriate inspection documents (according to EN 10204) on request. NOTE 2 The symbols and abbrev
48、iations to be used to designate the aluminium alloy, the type and thickness of the organic coating are those of the standards referred to in clause 2. Product testing shall be provided to a defined schedule and carried out by the manufacturer or by an approved body. A permanent quality system shall
49、be adopted by the manufacturer1). 4.2 Materials 4.2.1 Aluminium Aluminium alloys given in Table 1 are suitable provided that their properties conform to the values given in the relevant material standards (e.g. EN 485-2, EN 573-3). 1).E.g. quality management system based on EN ISO 9001. BS EN 508-2:2008EN 508-2:2008 (E) 14 Table 1 Alloys of aluminium Numerical designation Designation based on chemical symbol EN AW-3003 EN AW-Al Mn1Cu EN AW-3004 EN AW-Al Mn1Mg1 EN AW-3005 EN AW-Al Mn1Mg0,5 EN AW-3103 EN AW-Al Mn1 EN AW-3105 EN A
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1