EN 516-2006 en Prefabricated Accessories for Roofing - Installations for Roof Access - Walkways Treads and Steps《屋面用预制备件 屋顶通路的安装 过道 踏板和台阶》.pdf

1、BRITISH STANDARDBS EN516:2006Prefabricated accessories forroofing Installations for roof access Walkways, treads and stepsThe European Standard EN 516:2006 has the status of a British StandardICS 91.060.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49

2、g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 516:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2006 BSI 2006ISBN 0 580 48298 7National forewordThis British Standar

3、d is the official English language version of EN 516:2006. It supersedes BS EN 516:1995 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee B/208, Stairs and walkways, which has the responsibility to: A list of organizations represented on this committee

4、can be obtained on request to its secretary.Additional standards related to accessThis standard forms one of a group of British Standards covering permanent fittings to give access at height to structures including high buildings and chimneys, and plant. Others in the group are as follows. BS 3572,

5、Specification for access fittings for chimneys and other high structures in concrete or brickwork. BS 3678, Specification for access hooks for chimneys and other high structures in steel. BS 5395-3, Stairs, ladders and walkways Part 3: Code of practice for the design of industrial type stairs, perma

6、nent ladders and walkways.Where access is required to machinery, the requirements in BS EN ISO 14122, Safety of machinery Permanent means of access to machinery will apply.Attention is drawn to the BS 4592 series of standards which provide specifications for industrial type metal flooring, walkways

7、and stair treads.For portable ladders in aluminium and timber, attention is drawn to BS 2037 and BS 1129 respectively.Attention is also drawn to the requirements of the Building Regulations for England and Wales, The Building Regulations (Northern Ireland) and The Building Standards (Scotland) Regul

8、ations.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalo

9、gue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the

10、 text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.Summary of pagesThis document comprises a front cover

11、, an inside front cover, the EN title page,pages 2 to 21 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 516January 2006ICS 91.0

12、60.20 Supersedes EN 516:1995 English VersionPrefabricated accessories for roofing - Installations for roofaccess - Walkways, treads and stepsAccessoires prfabriqus pour couverture - Installationspour accs du tot - Passerelles, plans de marche etescabeauxVorgefertigte Zubehrteile fr Dacheindeckungen

13、-Einrichtungen zum Betreten des Daches - Laufstege,Trittflchen und EinzeltritteThis European Standard was approved by CEN on 7 December 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a natio

14、nal standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any o

15、ther language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, Fr

16、ance,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NO

17、RMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 516:2006: EEN 516:2006 (E) 2 Contents Page Foreword 4 1 Scope .5 2 Normative references .5 3 Terms and definitions.5 4 S

18、ymbols.5 5 Materials 6 6 Dimensions and construction requirements 6 6.1 General 6 6.2 Walkways.6 6.3 Treads 7 6.4 Steps 7 7 Requirements 10 7.1 Static load (test load), Classes 1 and 2 .10 7.2 Fatigue strength10 7.3 Reaction to fire and external fire performance .10 8 Testing .10 8.1 Static test.10

19、8.1.1 Number of specimens.10 8.1.2 Step test.10 8.1.3 Test at the anchorage point .11 8.2 Test of the fatigue strength11 9 Evaluation of conformity 14 9.1 General 14 9.2 Initial type testing14 9.2.1 General 14 9.2.2 Test report .15 9.3 Factory production control 15 9.3.1 General 15 9.3.2 Equipment .

20、15 9.3.3 Raw materials and components 15 9.3.4 Non-conforming products15 9.3.5 Design process .16 10 Instructions for mounting and use 16 11 Designation .16 12 Marking 16 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive .17

21、ZA.1 Scope and relevant characteristics .17 ZA.2 Procedure for attestation of conformity of walkways, treads and steps 18 ZA.2.1 System of attestation of conformity 18 ZA.2.2 EC Declaration of conformity.19 ZA.3 CE marking and labelling .19 Bibliography.21 EN 516:2006 (E) 3 Figure 1 Installation for

22、 roof access (diagrammatic section). 8 Figure 2 Walkway. 8 Figure 3 Tread 9 Figure 4 Step 9 Figure 5 Static test . 12 Figure 6 Dynamic test (fatigue strength). 13 Table ZA.1 Relevant clauses for walkways, treads and steps and intended use 18 Table ZA.2 System of attestation of conformity 18 Table ZA

23、.3 Assignment of evaluation of conformity tasks 19 EN 516:2006 (E) 4 Foreword This document (EN 516:2006) has been prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying and products for wall cladding”, the secretariat of which is held by IBN/BIN. This European S

24、tandard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2006, and conflicting national standards shall be withdrawn at the latest by July 2006. This document supersedes EN 516:1995. This document has been prepared

25、under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal

26、Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherland

27、s, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 516:2006 (E) 5 1 Scope This document applies to installations for roof access (building products) permanently fixed to the load-bearing construction of pitched roofs, to stand or to walk on du

28、ring inspection, maintenance and repair of facilities on the roof. It specifies essential dimensions, materials to be used, requirements with respect to the load-bearing capacity of the installation for roof access fastened to the roof construction including their fastening system, and the extent of

29、 testing. This document does not apply to permanently fixed ladders on pitched roofs. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of

30、the referenced document (including any amendments) applies. EN 364, Personal protective equipment against falls from a height Test methods EN 795, Protection against falls from a height Anchor devices Requirements and testing EN ISO 1140, Fibre ropes Polyamide 3-, 4- and 8-strand ropes (ISO 1140:200

31、4) EN ISO 1461, Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:1999) 3 Terms and definitions For the purpose of this document, the following definitions apply. 3.1 installation for roof access building product with a platform to stand or

32、 to walk on with one or more supports permanently fixed by means of associated fastening systems to the load-bearing construction of a pitched roof Note 1 See figure 1 Note 2 Depending on the size of the platform, installations for roof access are designated as walkways (see Figure 2), treads (see f

33、igure 3) or steps (see figure 4) 3.2 fastening system combination of products which fasten the walkways, treads and steps, to the load-bearing roof construction 3.3 load-bearing roof construction part of the roof construction which is able to carry potential loads and to transmit them to the buildin

34、g structure 4 Symbols b width EN 516:2006 (E) 6 l length R lanyard P test load roof slope 5 Materials Installations for roof access and their fastening systems shall be made of metal or equivalent material and be resistant to corrosion as well as to atmospheric and climatic influences. The material

35、shall be free from faults and inclusions that may impair their performance abilities. The corrosion resistance shall be at least equivalent to that of hot-galvanised steel with a protective layer according to EN ISO 1461. Parts of the fastening system beneath the roof covering may be from timber and

36、 shall then be protected against atmospheric and climatic influences. 6 Dimensions and construction requirements 6.1 General Installations for roof access shall be classified as follows: Class 1: Installations that shall not be used as anchorage points to which personal protective equipment against

37、fall or for restraint are attached; Class 2: Installations that may be used as anchorage points to which personal protective equipment against fall or for restraint are attached. The surfaces of the platforms of walkways, treads and steps shall be designed to avoid slipping of persons and collection

38、 of water and, where necessary, to minimise snow build-up. Constructions with sharp angles or edges have to be avoided. To accommodate roofs with different slopes, the connections between platform and supports shall be adjustable but they shall be designed to be secured against accidental disconnect

39、ion after installation. The type and size of the fastening system(s) shall be specified by the manufacturer. 6.2 Walkways Walkways are distinguished according to the width of their platforms as types A, B or C. The minimum width b of the platform shall be for: Type A: 250 mm, Type B: 350 mm and Type

40、 C: 430 mm. The length l of the platforms of all types shall be at least 500 mm. EN 516:2006 (E) 7 The platforms of walkways of Type B shall be provided with turn-ups or side battens of at least 20 mm on both long sides, measured from the platform surface, to prevent persons from slipping. The suppo

41、rts of walkways shall be designed in such a way that, after mounting on the roof construction, the inclination across the width b as well as across the length l is not greater than 3 from the horizontal. 6.3 Treads The platform of treads shall have a width b of at least 250 mm. The length l shall be

42、 at least 400 mm. The supports of treads shall be designed in such a way that, after mounting on the roof construction, the inclination across the width b as well as across the length l is not greater than 3 from the horizontal. 6.4 Steps The platform of steps shall have a size b l of at least 130 m

43、m 130 mm. On all sides, except the front and rear side, the platform of steps shall be provided with turn-ups or side battens of at least 20 mm, measured from the platform surface, to prevent persons from slipping. Furthermore, steps shall have a handle or a grip hole in the platform. The supports o

44、f steps shall be designed in such a way that, after mounting on the roof construction, the inclination across the width b as well as across the length l is not greater than 3 from the horizontal. EN 516:2006 (E) 8 Key 1 Rafter 2 Fastening system 3 Counter-batten 4 Batten 5 Supporting construction 6

45、Walkway, tread, step 7 Roofing b Width Figure 1 Installation for roof access (diagrammatic section) Key b Width l Length Figure 2 Walkway EN 516:2006 (E) 9 Key b Width l Length Figure 3 Tread Key b Width l Length Figure 4 Step EN 516:2006 (E) 10 7 Requirements 7.1 Static load (test load), Classes 1

46、and 2 Installations for roof access of Classes 1 and 2 including their fastening systems shall be designed for a single vertical static load of P 1,5 kN, applied in the most unfavourable position. Compliance with the requirements shall either be proved by means of a static calculation or, if this is

47、 not possible, the product shall be tested according to Clause 8. NOTE For further calculations see ENV 1993 and ENV 1999. Under this load the vertical deflection of walkways and tread platforms shall not exceed 1/100 of the span. The maximum deflection shall not exceed 15 mm. The vertical deviation

48、 from the original position of treads and steps, measured over the supports, shall not exceed 9 mm. The vertical deflection and/or deviation shall be measured relative to the load-bearing construction. Installations for roof access of Class 2 and their fastening systems shall be designed for a singl

49、e static load of P1 10 kN applied in a possible anchorage point in the usage direction. The test load according to EN 795 shall be increased accordingly if the installation for roof access of Class 2 is used by more than one person. 7.2 Fatigue strength Installations for roof access of Class 2 including their fastening systems shall be designed to withstand the dynamic load of the test according to 8.2 at any point where it is possible to attach personal protective equipment against fall or for restraint.