EN 546-1-2006 en Aluminium and aluminium alloys - Foil - Part 1 Technical conditions for inspection and delivery《铝和铝合金 箔 第1部分 检验和交付用技术条件》.pdf

1、BRITISH STANDARDBS EN 546-1:2006Aluminium and aluminium alloys Foil Part 1: Technical conditions for inspection and deliveryThe European Standard EN 546-1:2006 has the status of a British StandardICS 77.150.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g5

2、0g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 546-1:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2007 BSI 2007ISBN 978 0 580 50136 4National forewordThis

3、British Standard was published by BSI. It is the UK implementation of EN 546-1:2006. It supersedes BS EN 546-1:1997 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys.A list of organizations represented on NFE/35 can

4、 be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd.

5、 No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 546-1December 2006ICS 77.150.10 Supersedes EN 546-1:1996 English VersionAluminium and aluminium alloys - Foil - Part 1: Technicalconditions for inspection and deliveryAluminium et alliages daluminium - Feuille mince - Partie 1: Cond

6、itions techniques de contrle et de livraisonAluminium und Aluminiumlegierungen - Folien - Teil 1:Technische LieferbedingungenThis European Standard was approved by CEN on 25 November 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giv

7、ing this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official version

8、s (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus

9、, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EU

10、ROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 546-1:2006: EEN 546-1:2006 (E) 2 Contents Page Foreword3 1 Scope 4 2 Norm

11、ative references 4 3 Terms and definitions .4 4 Ordering information.5 5 Requirements.5 5.1 Production and manufacturing processes .5 5.2 Quality control6 5.3 Chemical composition 6 5.4 Mechanical properties.6 5.5 Freedom from defects .6 5.6 Tolerances on dimensions .6 5.7 Special properties6 6 Test

12、 procedure.6 6.1 Sampling.6 6.2 Methods of testing.8 6.3 Retests 8 7 Conformity with standards .9 8 Marking of products 9 9 Packaging .9 10 Complaints of non-conformity .9 Bibliography 10 EN 546-1:2006 (E) 3 Foreword This document (EN 546-1:2006) has been prepared by Technical Committee CEN/TC 132 “

13、Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2007, and conflicting national standards shall be withdrawn at the

14、latest by June 2007. This document supersedes EN 546-1:1996. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 6 “Foil and finstock“ to revise EN 546-1:1996. The following modifications have been made: Clause 3: deletion of subclauses 3.1 to 3.6. Reference to EN 12

15、258-1, and definition of converter foil, consumer/household foil and container foil added; Clause 4: title is changed, and wording is clarified; subclauses 5.2, 6.1.1 and 6.2.1: text amended. EN 546 comprises the following parts under the general title “Aluminium and aluminium alloys Foil“: Part 1:

16、Technical conditions for inspection and delivery Part 2: Mechanical properties Part 3: Tolerances on dimensions Part 4: Special property requirements Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsibl

17、e for identifying any or all such patent rights. CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licenses on standardised standard products under reasonable and not discriminatory conditions, then this product shall be removed from the corresponding standard. Ac

18、cording to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lith

19、uania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 546-1:2006 (E) 4 1 Scope This document specifies the technical conditions for inspection and delivery of wrought aluminium and aluminium alloy foil. The gau

20、ge range covered is 6 m to 200 m. It does not apply to lacquered, painted, embossed or laminated products. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, t

21、he latest edition of the referenced document (including any amendments) applies. EN 515, Aluminium and aluminium alloys Wrought products Temper designations EN 546-2, Aluminium and aluminium alloys Foil Part 2: Mechanical properties EN 546-3, Aluminium and aluminium alloys Foil Part 3: Tolerances on

22、 dimensions EN 546-4, Aluminium and aluminium alloys Foil Part 4: Special property requirements EN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: Chemical composition EN 12258-1:1998, Aluminium and aluminium alloys Terms and definitions Part 1: Genera

23、l terms EN 14242, Aluminium and aluminium alloys Chemical analysis Inductively coupled plasma optical emission spectral analysis EN 14361, Aluminium and aluminium alloys Chemical analysis Sampling from metal melts 3 Terms and definitions For the purposes of this document, the terms and definitions g

24、iven in EN 12258-1:1998 and the following apply. 3.1 converter foil rolled aluminium in the gauge range of 6 m to 200 m, produced either by double rolling or single rolling, typically soft annealed and supplied for further processing such as lacquering or laminating 3.2 consumer/household foil foil

25、in the gauge range of 10 m to 24 m, intended for general use, principally for use in culinary applications such as cooking and storage 3.3 container foil single rolled material in the gauge range 35 m to 200 m, produced at soft or intermediate temper and often involving alloys of the 3xxx and 8xxx s

26、eries. The foil can be coloured/printed, and is usually supplied lubricated for press forming into smooth or wrinkled walled containers for foodstuffs and the like EN 546-1:2006 (E) 5 4 Ordering information The order shall specify the product required and shall contain the following information : a)

27、 description of the product: type of converting and intended use; alloy designation; form of the product, i.e. single-rolled or double-rolled; b) temper designation of the material to be delivered as defined in EN 515; c) number of this European Standard EN 546-1, or separate specification, if any;

28、d) dimensions of the product: thickness; width and type of specified tolerance on width as defined in EN 546-3 (symmetrical, only plus, only minus); internal and external diameter of the coil/reel; core size and type; e) quantity (mass); f) type of lubrication, if specific; g) any special requiremen

29、ts agreed between purchaser and supplier, e.g: test certificates and inspection reports; marking of the products, e.g. identification, flagging of joints, etc; reference to drawings, e.g. for packaging, cores, etc; wettability; bright or matt outer surface of coil/reel (if double rolled). If special

30、 requirements are specified, the application shall be stated. 5 Requirements 5.1 Production and manufacturing processes Unless otherwise specified in the order, the production and manufacturing processes shall be left to the discretion of the supplier. Unless it is explicitly stated in the order, no

31、 obligation shall be placed on the supplier to use the same process for subsequent and similar orders. EN 546-1:2006 (E) 6 5.2 Quality control The manufacturer shall establish and maintain a quality management system, which should be at least equivalent to EN ISO 9001. The manufacturer shall establi

32、sh and maintain inspection plans defining all inspections and tests to be performed on the product to fulfil the requirements of this standard and any other requirement agreed according to Clause 6 of the present standard, their frequency and the type of record to be established. The inspection plan

33、 shall specify for each inspection or test whether it is to be performed per cast, per heat treatment batch, per inspection lot as defined in EN 12258-1 or per any other lot of importance. The inspection plan shall conform as a minimum to the test procedures and test requirements stipulated in this

34、standard. The inspection plan shall include additional schemes for appropriate process control. If required the inspection plan shall be submitted to the purchaser for approval before start of production. The manufacturer shall be responsible for carrying out all inspections and tests required by th

35、is standard, prior to the shipment of the product. If the purchaser wishes to inspect the product at the manufacturers site of production, he shall stipulate this at the time of placing the order. The extent of inspections shall be in accordance with Clause 6 of the present standard. Unless explicit

36、ly stated quality controls and inspections shall be performed on inspection lots. Products included in one inspection lot shall be manufactured in the same production unit. 5.3 Chemical composition The chemical composition shall be in conformity with the requirements specified in EN 573-3. 5.4 Mecha

37、nical properties The mechanical properties shall be in conformity with EN 546-2. 5.5 Freedom from defects The product shall be free from defects prejudicial to its suitable and proper use. 5.6 Tolerances on dimensions The tolerances on dimensions shall be in conformity with EN 546-3. 5.7 Special pro

38、perties Special property requirements shall be agreed between purchaser and supplier. 6 Test procedure 6.1 Sampling 6.1.1 Samples for chemical analysis Sampling shall be carried out at the time of casting according to EN 14361. The average content of each sample shall be within the specification for

39、 the chemical composition. NOTE EN 14361 includes criteria how to determine number, volume and shape of samples, about time and location of sampling and about the design and maintenance of the tools, in order to make sure that the average chemical composition of the sample is representative of the a

40、verage chemical composition of the whole melt. EN 546-1:2006 (E) 7 6.1.2 Specimens for mechanical testing 6.1.2.1 Location and size Specimens shall be taken from samples in such a way that it is possible to orientate the test pieces in relation to the product, as specified in 6.1.2.2. The specimens

41、shall be large enough to allow manufacture of the test pieces necessary to carry out the required tests and shall include sufficient metal to allow manufacture of test pieces for any retests required. 6.1.2.2 Orientation Specimens shall be taken in such a manner that the test pieces can be prepared

42、in the longitudinal direction. 6.1.2.3 Identification Each specimen shall be identified in such a way that after removal, it is still possible to identify the product from which it was taken and its location and orientation. If during the course of subsequent operations removal of the markings canno

43、t be avoided, new markings shall be made before the originals are removed. 6.1.2.4 Preparation Specimens shall be taken from the sample after completion of all the mechanical and heat treatment operations that the product has to undergo before delivery and which can influence the mechanical properti

44、es of the metal. In cases where this is not possible, the sample or specimens may be taken at an earlier stage, but they shall be subjected to the same treatment as that to which it is intended to submit the product concerned. Cutting shall be carried out in such a manner that it does not change the

45、 characteristics of the part of the specimen from which the test pieces are to be prepared. Thus, the dimensions of the specimens shall provide an adequate allowance to permit removal of the zone affected by cutting. Specimens shall not be treated in any way that alters their mechanical properties.

46、6.1.2.5 Number The number of specimens taken shall be sufficient to provide statistical evidence of long-term product conformity to the relevant properties specified in EN 546-2. When specific testing has been agreed between purchaser and supplier, the sampling frequency shall be increased to one sp

47、ecimen from each inspection lot of 10 000 kg or part thereof. For single coils weighing more than 10 000 kg each, only one specimen per coil shall be taken. 6.1.3 Test pieces for tensile test 6.1.3.1 Identification Each test piece shall be marked in such a manner that it is possible to identify the

48、inspection lot from which it was taken and, if required, its location and orientation in the product. If a test piece is identified by stamping, this shall not be in a place or manner which can interfere with subsequent testing. Where it is not convenient to mark a test piece, an identification tag

49、may be attached. 6.1.3.2 Number One test piece shall be taken from each specimen. EN 546-1:2006 (E) 8 6.1.3.3 Type Flat test pieces shall be used for all thicknesses covered by EN 546-2. The test piece shall be prepared so that both surfaces are included undisturbed. 6.1.4 Other tests For any other tests the procedures shall be as specified in EN 546-4. 6.2 Methods of testing 6.2.1 Analysis of chemical composition The ranges of application and the accuracy of the test procedure used shall be valid