1、BS EN 581-1:2017Outdoor furniture Seatingand tables for camping,domestic and contract usePart 1: General safety requirementsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 581-1:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementatio
2、n of EN 581-1:2017. Itsupersedes BS EN 581-1:2006 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee FW/0/2, Domestic and Contract Furniture.A list of organizations represented on this committee can beobtained on request to its secretary.This publication d
3、oes not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2017. Published by BSI Standards Limited 2017ISBN 978 0 580 90134 8ICS 97.140Compliance with a British Standard cannot confer immunity fromlegal o
4、bligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 March 2017.Amendments/corrigenda issued since publicationDate Text affectedBS EN 581-1:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 581-1 March 2017 ICS 97.140; 97.200.3
5、0 Supersedes EN 581-1:2006English Version Outdoor furniture - Seating and tables for camping, domestic and contract use - Part 1: General safety requirements Mobilier dextrieur - Siges et tables usage domestique, collectif et de camping - Partie 1 : Exigences gnrales de scurit Auenmbel - Sitzmbel un
6、d Tische fr den Camping-, Wohn- und Objektbereich - Teil 1: Allgemeine sicherheitstechnische Anforderungen This European Standard was approved by CEN on 9 January 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European S
7、tandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (Eng
8、lish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium,
9、 Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Sw
10、itzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN nati
11、onal Members. Ref. No. EN 581-1:2017 EBS EN 581-1:2017EN 581-1:2017 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Test probes 5 Figure 1 Measuring probes . 5 5 Safety requirements . 5 5.1 General 5 5.2 Tubular components 5 5.3 Shear and sq
12、ueeze points . 5 5.3.1 Shear and squeeze points when erecting, adjusting and folding away . 5 5.3.2 Shear and squeeze points under the influence of powered mechanisms . 5 5.3.3 Shear and squeeze points during use 6 6 Test report . 6 Annex A (informative) Schematic presentation of requirements and co
13、nditions concerning shear and squeeze points . 7 Figure A.1 Schematic presentation of requirements and conditions concerning shear and squeeze points 7 Annex B (informative) Rationale for injury of fingers 8 BS EN 581-1:2017EN 581-1:2017 (E) 3 European foreword This document (EN 581-1:2017) has been
14、 prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2017, and conflicting national standards
15、 shall be withdrawn at the latest by September 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 581-1:2006. Compared
16、 to EN 581-1:2006, the main modifications are: clarification of the definitions (camping, domestic and contract use) taken from Annex B and put in Clause 3 (so Annex B will be superseded), test method is deleted, edges and corners are modified to take into account accessible part during use (accessi
17、ble parts for seating and tables are defined), tubular components are defined, requirements for gaps and holes removed, addition of an Annex B (informative) as a rationale to explain the risks covered with requirements in Clause 5. According to the CEN-CENELEC Internal Regulations, the national stan
18、dards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, L
19、uxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 581-1:2017EN 581-1:2017 (E) 4 1 Scope This part of EN 581 specifies the general safety requirements for outdoor seating and tables for campin
20、g, domestic and contract for use by adults, without regard to materials, design/construction or manufacturing processes. It does not apply to seating for spectator facilities. It does not include requirements for the durability of upholstery materials, castors, reclining and tilting mechanisms and s
21、eat height adjustment mechanisms. Mechanical safety requirements are covered by EN 581-2 for seating and EN 581-3 for tables. Annex A (informative) is a schematic presentation of requirements and conditions concerning shear and squeeze points. Annex B (informative) is a rationale concerning fingers
22、injury. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including a
23、ny amendments) applies. EN 581-2:2015, Outdoor furniture - Seating and tables for camping, domestic and contract use - Part 2: Mechanical safety requirements and test methods for seating EN 581-3:2007, Outdoor furniture - Seating and tables for camping, domestic and contract use - Part 3: Mechanical
24、 safety requirements and test methods for tables 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 automatic locking mechanism mechanism which engages without guidance by the user and prevents unintended movement 3.2 shear and squeeze point she
25、ar and squeeze points exist if the distance between two accessible parts moving relative to each other can be more or equal than 7 mm and less or equal than 18 mm in any position during movement 3.3 outdoor furniture for contract use outdoor furniture intended for non-private use in places with publ
26、ic access 3.4 outdoor furniture for domestic use outdoor furniture intended for private use in places without public access 3.5 outdoor furniture for camping use outdoor furniture foldable or knock-down and light-weight, intended for use in connection with camping and travelling BS EN 581-1:2017EN 5
27、81-1:2017 (E) 5 4 Test probes There shall be three cylindrical probes with diameters of 00,17+mm, 0,1012 +mm and 0,1018 +mm with hemispherical ends, see Figure 1. Key 1 00,17+mm, 0,1012 +mm and 0,1018 +mm Figure 1 Measuring probes 5 Safety requirements 5.1 General In order to avoid physical injury w
28、hen the product is in its intended position of use, all edges and corners shall be rounded, chamfered or otherwise protected. This applies to: Seating: Edges of the seat, back rest and arm rests and any part of the bottom surface of the seat at a distance less than 120 mm from any edge, where a fing
29、er can commonly access; Tables: Table tops, any part of the underside of the top surface at a distance less than 500 mm from any edge below the table, where a knee and/or an arm can commonly access. All other parts shall be free from burrs, sharp edges and sharp points. Movable and adjustable parts
30、shall be designed so that injuries and inadvertent operation are avoided. It shall not be possible for any load bearing part of the furniture to come loose unintentionally. All parts which are lubricated to assist sliding shall be designed to protect users from lubricant stains when in normal use. 5
31、.2 Tubular components There shall be no accessible holes in the ends of tubular components with a diameter between 7 mm to 12 mm and with a depth more or equal to 10 mm. The bottom of tubular legs in contact with the floor shall be closed or capped, however, holes in them are allowed as long as they
32、 are not between 7 and 12 mm. These requirements shall be assessed using the test probes (Clause 4). 5.3 Shear and squeeze points 5.3.1 Shear and squeeze points when erecting, adjusting and folding away Unless 5.3.2 or 5.3.3 are applicable, shear and squeeze points that are created only during erect
33、ing, adjusting or folding away are acceptable providing the user can be assumed to be in control of his/her movements and to be able to cease applying the force immediately on experiencing pain. 5.3.2 Shear and squeeze points under the influence of powered mechanisms There shall be no accessible she
34、ar and squeeze points created by parts of the furniture operated by powered mechanisms, e.g. mechanical springs and gas lifts. This requirement shall be assessed using the test probes (Clause 4). BS EN 581-1:2017EN 581-1:2017 (E) 6 5.3.3 Shear and squeeze points during use There shall be no accessib
35、le shear and squeeze points created by loads applied during normal use. Shear and squeeze points are not acceptable if there is a risk of injury created by the weight of the user during normal movements and actions, e.g. attempting to move the seating by lifting the seat or by adjusting the backrest
36、. This requirement shall be assessed using the test probes (Clause 4). For loungers, the loads applied during normal use are the loads used for the following mechanical tests in Table 1 of EN 581-2:2015: Test 2: Additional seat and leg rest static load; Test 3: Seat and back durability; Test 4: Addi
37、tional seat durability; Test 5: Durability on back rest mechanism. For other seating, the loads applied during normal use are the loads used for the following mechanical tests in Table 2 of EN 581-2:2015: Test 2: Seat front edge static; Test 3: Combined seat and back durability; Test 4: Durability t
38、est on seating with a multi-position back. For tables, the loads applied during normal use are the loads used for the following mechanical tests in Table 1 of EN 581-3:2007: Test 1: Vertical static load on main surface; Test 4: Vertical static load on ancillary surface; Test 5: Horizontal durability
39、 test. 6 Test report The test report shall include at least the following information: a) reference to this part of the European Standard (EN 581-1:2017); b) details of piece of furniture tested; c) any defects observed before testing; d) the test results according to the applicable clauses; e) comp
40、liance with the requirements; f) the name and address of the test facility; g) the date of test. BS EN 581-1:2017EN 581-1:2017 (E) 7 Annex A (informative) Schematic presentation of requirements and conditions concerning shear and squeeze points Figure A.1 is a Schematic presentation of requirements
41、and conditions concerning shear and squeeze points. Figure A.1 Schematic presentation of requirements and conditions concerning shear and squeeze points BS EN 581-1:2017EN 581-1:2017 (E) 8 Annex B (informative) Rationale for injury of fingers Clause Title Risk cover 5.1 General Risk of cutting a par
42、t of the users body when in contact with the product 5.2 Tubular components Finger entrapment in holes on tubular component and damage on floors 5.3 Shear and squeeze points Shearing and squeezing of fingers, thumbs excluded This page deliberately left blankBSI is the national body responsible for p
43、reparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, indus
44、try, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes
45、 and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Cen
46、tre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organiz
47、ations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international
48、standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly dis
49、play the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may b
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1