1、BS EN 6059-304:2017Aerospace series Electrical cables, installation Protection sleeves Test methodsPart 304: FlammabilityBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 6059-304:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementatio
2、n of EN 6059-304:2017. The UK participation in its preparation was entrusted to TechnicalCommittee ACE/6, Aerospace avionic electrical and fibre optic technology.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to inc
3、lude all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017.Published by BSI Standards Limited 2017ISBN 978 0 580 96071 0 ICS 13.220.40; 49.060 Compliance with a British Standard cannot confer immunity from legal obligati
4、ons.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2017.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 6059-304:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 6059-304 March 2017 ICS 13.220
5、.40; 49.060 English Version Aerospace series - Electrical cables, installation - Protection sleeves - Test methods - Part 304: FlammabilitySrie arospatiale - Cbles lectriques, installation - Gaines de protection - Mthodes dessais - Partie 304: Rsistance au feu Luft- und Raumfahrt - Elektrische Leitu
6、ngen, Installation - Schutzschluche - Prfverfahren - Teil 304: Flammwidrigkeit This European Standard was approved by CEN on 6 February 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nat
7、ional standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A ve
8、rsion in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus,
9、 Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and Unite
10、d Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 6
11、059-304:2017 EBS EN 6059-304:2017EN 6059-304:2017 (E) 2 Contents Page European foreword 3 1 Scope 4 2 Normative references 4 3 Preparation of specimens 4 4 Apparatus. 5 5 Methods 5 6 Requirements . 8 BS EN 6059-304:2017EN 6059-304:2017 (E) 3 European foreword This document (EN 6059-304:2017) has bee
12、n prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member
13、countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2017, and conflicting national standards shall be withdrawn at the latest by September
14、 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organ
15、izations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,
16、Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 6059-304:2017EN 6059-304:2017 (E) 4 1 Scope This European Standard specifies methods for determining the flammability characteristics of protective slee
17、ves, including heat shrink dual wall sleeves, for electric cable and cable bundles. It shall be used together with EN 6059-100. These tests are designed to satisfy the requirements in JAR-25 Section 1, Part 1, Appendix F. There are two methods included in this standard: Method 1 Applicable for texti
18、le fabric sleeves. Method 2 Applicable non-textile sleeves for use on electrical/ optical cables and harness components. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, o
19、nly the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1057, Copper and copper alloys Seamless, round copper tubes for water and gas in sanitary and heating applications EN 3844-1, Aerospace series Flammability of n
20、on-metallic materials Part 1: Small burner test, vertical Determination of the vertical flame propagation EN 6059-100, Aerospace series Electrical cables, installation Protection sleeves Test methods Part 100: General JAR-25, Joint Aviation Requirements for Large Aircraft 3 Preparation of specimens
21、3.1 Method 1 The specimen for fabric sleeves shall be a rectangular shape of at least 75 mm by 305 mm. 3.2 Method 2 A length of sleeving of at least 250 mm is to be mounted on a bundle of 7 AD 8 cables which has been covered in a copper braid 1). If necessary to ensure that the sleeve is correctly f
22、itted it may be secured at either end by ptfe/glass ties. Figure 1. Heat shrinkable sleeves shall be recovered onto a copper tube, Table 1, of diameter approximately one size larger than the specified maximum recovered internal diameter. The copper tube shall have a maximum wall of not greater than
23、1,05 mm. The specimen shall be marked 100-105 mm from the lower end to indicate the central point for flame application. 1) Alternatively a length of thin wall copper tube pipe could be substituted for the cable bundle. BS EN 6059-304:2017EN 6059-304:2017 (E) 5 4 Apparatus 4.1 Test chamber Method 1:
24、 the test chamber and specimen holder is described in EN 3844-1 alternatively the chamber used for Method 2 can be utilised. Method 2: this shall be a chamber measuring not less than 700 mm high 300 mm wide 300 mm deep, open at the top, open at the front and situated in a draught-free environment bu
25、t with sufficient air supply to provide normal combustion. General arrangements are shown in Figures 1 and 2. 4.2 Burner Bunsen type gas burner: the burner shall have a 6 mm inlet, a needle valve in the base for gas adjustment, a nominal bore of 9,5 mm and a barrel of approximately 100 mm above the
26、air inlets. Methane, propane or natural gas may be used provided it meets the temperature requirements of 5.2. WARNING NOTE Care should be exercised in setting up and performing this test as toxic fumes may be given off during combustion. The test chamber shall be placed in a fume cabinet that will
27、allow evacuation of gaseous products of combustion at the end of the test. 5 Methods 5.1 Method 1 Vertical test The specimen shall be hung vertically in the centre of the test cabinet. For fabrics, the direction of weave corresponding to the most critical flammability conditions must be parallel to
28、the longest dimension. Each specimen must be supported vertically. The test shall be carried out in accordance with EN 3844-1 and the flame shall be not less than 1550F (843,33 C) when measured in the centre of the flame Six separate specimens shall be tested, three with application times of 12-14 s
29、 and three with application times of 60-62 s. 5.2 Method 2 60test The specimen shall be placed at an angle of 60 with the horizontal in the test cabinet. The specimen shall be parallel to and 150 mm from the front of the chamber. The lower end of the specimen must be held rigidly. The upper end of t
30、he specimen be retained either by attaching it to a cable which is pass over a pulley to a mass or by means of a spring anchored at the top so that the specimen is held tautly throughout the flammability test. The burner shall be positioned so that hottest part of the flame is applied to the test ma
31、rk. The burner must be mounted underneath the test mark on the specimen, perpendicular to the specimen and at an angle of 30 to the vertical plane of the specimen. See Figure 2. The flame shall be adjusted to provide an overall height of approximately 76 mm with an inner cone approximately one third
32、 of the flame height. The hottest part of the flame, tip of the inner cone, is to be measured with a calibrated thermocouple pyrometer, and shall be between 950 C and 965 C. BS EN 6059-304:2017EN 6059-304:2017 (E) 6 The flame is to be applied to the specimen for 30-32 s and on removal of the flame t
33、he maximum after burn time, burn length and the maximum time of any flaming droplets shall be recorded. Burn length is the distance from the lowest to the highest points where the flame has caused partial or complete consumption and charring. Ignore any areas that are sooted, warped or discoloured a
34、nd areas where material has shrunk or melted away from the heat source. Table 1 Copper tube sizes (EN 1057) Nominal tube OD mm 6 8 10 12 15 22 28 35 42 Wall thickness mm 0,6 - 0,8 0,6 - 0,8 0,6 - 0,80 0,6 - 0,80 0,7 - 1,0 0,9 - 1,2 0,9 - 1,2 1,2 - 1,5 1,2 - 1,5 Figure 1 Method 1 Vertical test BS EN
35、6059-304:2017EN 6059-304:2017 (E) 7 Key 1 Box construction aluminium alloy 3,15 mm 2 Upper datum point 3 Pulley support bracket (lowthermal conductivity) 4 Support frame open at front 5 Weights as required 6 600 mm Distance between reference marks 7 Flame application point (flame centre datum) 8 Bot
36、tom clamp support (lowthermal conductivity) 9 Bunsen burner support (lowthermal conductivity) a approx. Figure 2 Method 2 60test BS EN 6059-304:2017EN 6059-304:2017 (E) 8 6 Requirements A minimum of three specimens per flame application time shall be tested and results be not greater than. 6.1 Metho
37、d 1 Application time 12 s 60 s Maximum burn length 203 mm 152 mm Flame extinction after burner removal 15 s 15 s Droplets maximum flaming after dropping 5 s 3 s 6.2 Method 2 The maximum burn length shall not exceed 76 mm and the maximum flame time after removal of the flame source shall not exceed 3
38、0 s. Droplets from the test specimen shall not continue to flame for more than a maximum of 3 s. Application time 30 s Maximum burn length 76 mm Maximum after burn time 30 s Maximum time of any flaming droplets 3 s This page deliberately left blankBSI is the national body responsible for preparing B
39、ritish Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, gover
40、nment, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and acros
41、s all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying
42、 standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, ha
43、rd copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardiz
44、ation bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the s
45、tandard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may
46、 be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard cop
47、y format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by
48、choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on
49、 our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1